P6300 Trac Adapter
Product Information
The Juno Trac Adapter is a component used for installing
fixtures onto Juno Trac tracks. It is important to read and follow
the installation instructions provided in this manual to ensure
proper installation and usage.
Installation Instructions
- Step 1: Find the latch and the polarity line. Align the parts
as shown in Fig. 1 and insert the adapter box into the track.
LATCH
POLARITY LINE
- Step 2: Pull down the latch while rotating the adapter box 90
degrees clockwise, as shown in Fig. 2.
- Step 3: Final Position – The latch snaps into place between the
extrusion rails. The arrows on the latch should point towards the
polarity line, as shown in Fig. 3.
- SECOND CIRCUIT POSITIONING
- Step 1: Raise the contact marked P (on switch side) by
inserting a thin screwdriver blade under the contact. Pull it up
into position as shown in Fig. 4.
(INSERT)
(PULL)
(ROTATE)
P CONTACT
(LIFT)
- Step 2: Insert the contact support (supplied with 2-circuit
Trac section) by tilting and snapping it into position under the P
contact, as shown in Fig. 5.
- Step 3: Ensure the contact support is snapped and locked into
position, as shown in Fig. 6. Follow the instructions for inserting
into the track.
CONTACT SUPPORT
Troubleshooting
Problem: Fixture doesn’t turn on
- Cause: Track not energized
- Remedy: Ensure track has power
- Cause: Adapter switch is in the Off position
- Remedy: Ensure the power switch on the track fixture adapter is
in the On position, see Fig. 9 - Cause: Fixture installed incorrectly
- Remedy: Ensure fixture is installed correctly, with the arrows
on the latch pointing towards the polarity line as shown in Fig.
3 - Cause: Bent contacts from installing the fixture
incorrectly - Remedy: Ensure contacts aren’t bent from installing the fixture
incorrectly, see Fig. 7
P Contact adjusted incorrectly
Ensure P contact isn’t bent from adjusting incorrectly, see Fig.
8
Switch Positions
Correct Single Circuit Position: Used with T,
TU, and R Series Track
Correct Two Circuit Position: Used with TU
Series Track
Move Switch To On Position:
* Juno Trac adapter size and style may vary.
P6300 Rev 10/2022
INSTALLATION INSTRUCTIONS
For Juno Trac Adapter*
WARNING Read all of these installation instructions before installing.
SAVE THESE INSTRUCTIONS
FIXTURE INSTALLATION Step 1 Find the latch and the polarity line. Align parts as shown and insert the adapter box into the track. (Fig. 1)
Fig. 1
LATCH
POLARITY LINE
Fig. 2
Coming Soon
Step 2 Pull down the latch while rotating the adapter box 90 degrees clockwise. (Fig. 2)
Step 3 Final Position: Latch snaps into place between extrusion rails. Arrows on latch point toward the polarity line. (Fig. 3)
Fig. 3
SECOND CIRCUIT POSITIONING
Step 1 Raise the contact marked “P” (on switch side) by inserting a thin screwdriver blade under contact. Pull up into position as shown. (Fig. 4)
(INSERT)
(PULL)
(ROTATE)
Fig. 4
“P” CONTACT
(LIFT)
Step 2 Insert contact support (supplied with 2-circuit Trac section) by tilting and snapping into position under the “P” contact as shown. (Fig. 5)
Fig. 5
Step 3 Ensure contact support is snapped and locked into position. (Fig. 6) Follow instructions for inserting into track.
CONTACT SUPPORT
Fig. 6
FINAL POSITION OF CONTACT SUPPORT
*Juno Trac adapter size and style may vary.
One Lithonia Way · Conyers, GA 30012 · 1-800-705-SERV (7378) · www.acuitybrands.com
©2020 Acuity Brands Lighting, Inc.
P6300 Rev 10/2022
1 of 2
Coming Soon
INSTALLATION INSTRUCTIONS
For Juno Trac Adapter*
TROUBLESHOOTING
Problem
Fixture doesn’t turn on
Cause Track not energized Adapter switch is in the
“Off” position
Fixture installed incorrectly
Remedy Ensure track has power
Ensure the power switch on the track fixture adapter is in the “On” position, see Fig. 9
Ensure fixture is installed correctly, with the arrows on the latch pointing towards the polarity line as shown in Fig. 3
Ensure contacts aren’t bent from installing the fixture incorrectly, see Fig. 7
Fig. 7
“P” Contact adjusted incorrectly
Ensure “P” contact isn’t bent from adjusting incorrectly, see Fig. 8
Bent contact from adjusting the wrong contact, see Fig. 4, 5, & 6 for proper adjustment method
Correct
Single Circuit Position
Used with T, TU, and R Series Track
Incorrect
Bent Contact
Raised Contact
Fig. 8
Correct
Two Circuit Position
Used with TU Series Track
Incorrect
Bent Contact
Raised Contact
Fig. 9
Move Switch To “On” Position
Off
On
One Lithonia Way · Conyers, GA 30012 · 1-800-705-SERV (7378) · www.acuitybrands.com
©2020 Acuity Brands Lighting, Inc.
P6300 Rev 10/2022
2 of 2
Acuity Brands | Lighting, Controls, and Building Management Solutions
