P6300 Trac Adapter
Product Information: Juno Trac Adapter
Installation Instructions
Before installing the Juno Trac Adapter, please read all of the
following installation instructions carefully. Remember to save
these instructions for future reference.
Fixture Installation
Step 1: Find the latch and the polarity line.
Align the parts as shown in Figure 1 and insert the
adapter box into the track.
Step 2: Pull down the latch while rotating the
adapter box 90 degrees clockwise, as shown in Figure
2.
Step 3: The final position should have the
latch snapped into place between the extrusion rails. The arrows on
the latch should be pointing toward the polarity line, as shown in
Figure 3.
Second Circuit Positioning
Step 1: Raise the contact marked P (on switch
side) by inserting a thin screwdriver blade under the contact. Pull
it up into position as shown in Figure 4.
Step 2: Insert the contact support (supplied
with the 2-circuit Trac section) by tilting and snapping it into
position under the P contact, as shown in Figure 5.
Step 3: Ensure that the contact support is
snapped and locked into position, as shown in Figure 6.
Follow the instructions for inserting it into the track.
Troubleshooting
Problem: Fixture doesn’t turn on
Cause: Track not energized
Remedy: Ensure the track has power.
Problem: Adapter switch is in the Off
position
Remedy: Ensure the power switch on the track
fixture adapter is in the On position, as shown in Figure
9.
Problem: Fixture installed incorrectly
Remedy: Ensure the fixture is installed
correctly, with the arrows on the latch pointing towards the
polarity line as shown in Figure 3.
Problem: Contacts aren’t bent from installing
the fixture incorrectly
Remedy: Ensure contacts aren’t bent from
adjusting incorrectly, as shown in Figure 7.
Problem: P contact adjusted incorrectly
Remedy: Ensure the P contact isn’t bent from
adjusting incorrectly, as shown in Figure 8.
Note: The Juno Trac adapter size and style may
vary.
INSTALLATION INSTRUCTIONS
For Juno Trac Adapter*
WARNING Read all of these installation instructions before installing.
SAVE THESE INSTRUCTIONS
FIXTURE INSTALLATION Step 1 Find the latch and the polarity line. Align parts as shown and insert the adapter box into the track. (Fig. 1)
Fig. 1
LATCH
POLARITY LINE
Fig. 2
Coming Soon
Step 2 Pull down the latch while rotating the adapter box 90 degrees clockwise. (Fig. 2)
Step 3 Final Position: Latch snaps into place between extrusion rails. Arrows on latch point toward the polarity line. (Fig. 3)
Fig. 3
SECOND CIRCUIT POSITIONING
Step 1 Raise the contact marked “P” (on switch side) by inserting a thin screwdriver blade under contact. Pull up into position as shown. (Fig. 4)
(INSERT)
(PULL)
(ROTATE)
Fig. 4
“P” CONTACT
(LIFT)
Step 2 Insert contact support (supplied with 2-circuit Trac section) by tilting and snapping into position under the “P” contact as shown. (Fig. 5)
Fig. 5
Step 3 Ensure contact support is snapped and locked into position. (Fig. 6) Follow instructions for inserting into track.
CONTACT SUPPORT
Fig. 6
FINAL POSITION OF CONTACT SUPPORT
*Juno Trac adapter size and style may vary.
One Lithonia Way · Conyers, GA 30012 · 1-800-705-SERV (7378) · www.acuitybrands.com
©2020 Acuity Brands Lighting, Inc.
P6300 Rev 10/2022
1 of 2
Coming Soon
INSTALLATION INSTRUCTIONS
For Juno Trac Adapter*
TROUBLESHOOTING
Problem
Fixture doesn’t turn on
Cause Track not energized Adapter switch is in the
“Off” position
Fixture installed incorrectly
Remedy Ensure track has power
Ensure the power switch on the track fixture adapter is in the “On” position, see Fig. 9
Ensure fixture is installed correctly, with the arrows on the latch pointing towards the polarity line as shown in Fig. 3
Ensure contacts aren’t bent from installing the fixture incorrectly, see Fig. 7
Fig. 7
“P” Contact adjusted incorrectly
Ensure “P” contact isn’t bent from adjusting incorrectly, see Fig. 8
Bent contact from adjusting the wrong contact, see Fig. 4, 5, & 6 for proper adjustment method
Correct
Single Circuit Position
Used with T, TU, and R Series Track
Incorrect
Bent Contact
Raised Contact
Fig. 8
Correct
Two Circuit Position
Used with TU Series Track
Incorrect
Bent Contact
Raised Contact
Fig. 9
Move Switch To “On” Position
Off
On
One Lithonia Way · Conyers, GA 30012 · 1-800-705-SERV (7378) · www.acuitybrands.com
©2020 Acuity Brands Lighting, Inc.
P6300 Rev 10/2022
2 of 2
Acuity Brands | Lighting, Controls, and Building Management Solutions
