Trac Adapter
Product Information:
The Juno Trac Adapter is a versatile accessory that allows for
easy installation of fixtures onto Juno track systems. It is
compatible with various sizes and styles of Juno Trac adapters.
Key Features:
- Easy installation
- Compatible with Juno track systems
- Versatile design
Product Usage Instructions:
Fixture Installation:
- Find the latch and the polarity line on the adapter box.
- Align the parts as shown in Fig. 1.
- Insert the adapter box into the track.
- Pull down the latch while rotating the adapter box 90 degrees
clockwise.
- The latch should snap into place between the extrusion rails.
Ensure that the arrows on the latch point toward the polarity
line.
Second Circuit Positioning:
- Raise the contact marked P (on switch side) by inserting a thin
screwdriver blade under the contact. Pull it up into position as
shown in Fig. 4.
- Insert the contact support (supplied with the 2-circuit Trac
section) by tilting and snapping it into position under the P
contact as shown in Fig. 5.
- Ensure that the contact support is snapped and locked into
position as shown in Fig. 6.
Troubleshooting:
If you encounter any issues with the fixture, refer to the
following troubleshooting steps:
| Problem | Cause | Remedy |
|---|---|---|
| Fixture doesn’t turn on | Track not energized Adapter switch is in the Off position Fixture installed incorrectly | Ensure track has power Ensure the power switch on the track fixture adapter is in the On position, see Fig. 9 Ensure fixture is installed correctly, with the arrows on the latch pointing towards the polarity line as shown in Fig. 3 |
| P Contact adjusted incorrectly | Ensure P contact isn’t bent from adjusting incorrectly, see Fig. 8 Bent contact from adjusting the wrong contact, see Fig. 4, 5, & 6 for proper adjustment method | Adjust the P contact correctly as shown in Fig. 8 |
Note: The correct single circuit and two circuit positions are
shown in Fig. 8 and Fig. 9
respectively.
Always make sure the switch on the adapter is in the On position
for proper functionality.
For further assistance, refer to the complete user manual or
contact customer support.
INSTALLATION INSTRUCTIONS
For Juno Trac Adapter*
WARNING Read all of these installation instructions before installing.
SAVE THESE INSTRUCTIONS
FIXTURE INSTALLATION Step 1 Find the latch and the polarity line. Align parts as shown and insert the adapter box into the track. (Fig. 1)
Fig. 1
LATCH
POLARITY LINE
Fig. 2
Coming Soon
Step 2 Pull down the latch while rotating the adapter box 90 degrees clockwise. (Fig. 2)
Step 3 Final Position: Latch snaps into place between extrusion rails. Arrows on latch point toward the polarity line. (Fig. 3)
Fig. 3
SECOND CIRCUIT POSITIONING
Step 1 Raise the contact marked “P” (on switch side) by inserting a thin screwdriver blade under contact. Pull up into position as shown. (Fig. 4)
(INSERT)
(PULL)
(ROTATE)
Fig. 4
“P” CONTACT
(LIFT)
Step 2 Insert contact support (supplied with 2-circuit Trac section) by tilting and snapping into position under the “P” contact as shown. (Fig. 5)
Fig. 5
Step 3 Ensure contact support is snapped and locked into position. (Fig. 6) Follow instructions for inserting into track.
CONTACT SUPPORT
Fig. 6
FINAL POSITION OF CONTACT SUPPORT
*Juno Trac adapter size and style may vary.
One Lithonia Way · Conyers, GA 30012 · 1-800-705-SERV (7378) · www.acuitybrands.com
©2020 Acuity Brands Lighting, Inc.
P6300 Rev 10/2022
1 of 2
Coming Soon
INSTALLATION INSTRUCTIONS
For Juno Trac Adapter*
TROUBLESHOOTING
Problem
Fixture doesn’t turn on
Cause Track not energized Adapter switch is in the
“Off” position
Fixture installed incorrectly
Remedy Ensure track has power
Ensure the power switch on the track fixture adapter is in the “On” position, see Fig. 9
Ensure fixture is installed correctly, with the arrows on the latch pointing towards the polarity line as shown in Fig. 3
Ensure contacts aren’t bent from installing the fixture incorrectly, see Fig. 7
Fig. 7
“P” Contact adjusted incorrectly
Ensure “P” contact isn’t bent from adjusting incorrectly, see Fig. 8
Bent contact from adjusting the wrong contact, see Fig. 4, 5, & 6 for proper adjustment method
Correct
Single Circuit Position
Used with T, TU, and R Series Track
Incorrect
Bent Contact
Raised Contact
Fig. 8
Correct
Two Circuit Position
Used with TU Series Track
Incorrect
Bent Contact
Raised Contact
Fig. 9
Move Switch To “On” Position
Off
On
One Lithonia Way · Conyers, GA 30012 · 1-800-705-SERV (7378) · www.acuitybrands.com
©2020 Acuity Brands Lighting, Inc.
P6300 Rev 10/2022
2 of 2
Acuity Brands | Lighting, Controls, and Building Management Solutions
