AR7102401 Stainless Steel High Arc Kitchen Faucet
Product Information
The product is a faucet that is designed for easy installation
and has a durable finish. It complies with California water
efficiency regulations, California Proposition 65, and the Federal
Safe Drinking Water Act. The faucet has a water flow rate of 1.8
gallons per minute (6.8 liters per minute) and comes with a
screened washer pre-installed in the conical nut. The maximum deck
thickness for installation is 2 inches (50mm), and it has a
standard 3/8 inch pipe connection with a G1/2 adapter included. The
product is available in both single-hole and 3-hole
configurations.
Product Usage Instructions
- Before beginning installation, read all instructions and
warnings thoroughly. - Clean the water pipe thoroughly to remove any dirt or
deposits. - Remove the brass lock nut, washer, and washer from the thread
rod counter-clockwise. - Attach the O-ring to the faucet body.
- If the sink is uneven, use silicone under the gasket for a
secure fit. - Fasten the thread pipe to the base of the faucet body
clockwise. - Slide the tubes down through the mounting hole and place the
faucet on the sink. - If the sink is uneven, use silicone under the gasket for a
secure fit. - Apply Teflon tape to the quick connect installation, if
necessary. - Use the triangle fastener when the thickness of the sink
requires it.
Installation instructions
15.4″(390)
You may need
For easy installation of your faucet you will need: To READ ALL the instructions completely before beginning. To READ ALL warnings, care, and maintenanceinformation.
Cleaning and Care Care should be given to the cleaning of this product. Although its finish is extremely durable, It can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
With 1.8 gpm are compliant with California water effi ciency regulations,Complies with California Proposition 65 and with the Federal Safe Drinking Water Act.
Water Use Information: 1.8 gpm 6.8L/min, You can choose to replace the current limiting device and face the water pipe square.
screened washer (pre-installed in the conical nut)
1.8gpm water face on faucet
or
8″(200)
8.5″(215)
9.6″x2.4″x0.4″ (245x62x10)
Ø2″(50)
3″(75)
Ø1.26″(32)
2″(50mm) Max. deck Thickness
3/8″
3/8″ standard pipe connection G1/2″ adapter included
single-hole
Ø1.4″(35)
unit:inch(mm)
3-hole
Before installing the valves, clean the water pipe thoroughly to avoid dirt and deposits.
3.A
1 1
2
1
1
3 4 5 6 7
1.Remove the brass lock nut (6) from the thread rod counter-clockwise, remove the washer (5) and washer (3)
2
1. Make sure attach the O-ring(2) to the faucet body. 2.Slide tubes down through mounting hole andfaucet on sink. Option: If sink is uneven, use silicone under the gasket.
3.B
Option: If sink is uneven, use 1 silicone 2 under the 3 gasket.
1 3
1.Make sure fasten the thread pipe(3) to the base of the faucet body clock-wise.
1. Make sure
attach the
O-ring(2) to the
faucet body.
2.Slide 9.6″
decorated
plate with gasket(3) up over tubes
and mounting stud.
Slide tubes down through mounting
hole and faucet, 9.6″decorated
plate with gasket on sink.
4
5
ca. c1a.01000mm
3
4
15
5
6
7
NOT WITH apply
9
teflon tape to the quick connect
installation.
1.Use the triangle fastener(15) when the thickness of sink <5mm. 2.Place Triangle fastener15 and washer(4) and metal plate(5) over mounting stud(3) under sink. Secure with mounting nut(6), tighten the screws(7) to fix the faucet body
6
1 model 1:Stop 2
3 model 2:Standard Flow Aerator
model 3:Spray
water flow pattern unchanged when the water is turned off.
8 16
10 or 12
11
1.Attach pull-out hose (11) on quick connects (9). Press the quick connects firmly. 2. Attach weight ball(16) to pull-out hose (11) Make sure the pull-out hose is not blocking by other objects and not touching the ground. The appropriate height for gravity ball installation is 100mm. 3.Attach supply hot(8)and cool lines(9) . 4. If the anglve is G1/2”, please use G3/8” standard pipe connection G1/2” adapter included (12) . Do not overtighten. Turn water back on.
Check for Leaks Turn on water and check all connections at arrows for leaks. Refer back to the appropriate installation instructions and retighten if necessary.
The sprayer can be removed by pulling directly out from the spout.
