900017 Modern Crystal Design 3-Light Oil Rubbed Bronze Circle Chandelier
Product Information
The product is a lighting fixture that comes in two models,
900017 and 900018. It requires a supply circuit of 120V and 60Hz
with a maximum wattage of 3*E26*60W. It is compatible with 11W LED
A19 bulbs that are not included in the package. The package
includes components such as Arm, Ring, Light Cluster, Crystal,
Chain & Loops, Cup, Canopy, and Bracket with Nipple. Parts bag
includes parts such as Junction Box, Leading Wires, Wire Nut,
Mounting Bracket with Nipple, Mounting Screw, Canopy Hanging Loop
Collar, Chain Locker, Chain, Fixture Wire Loop, Small Ring, Cap Hex
Nut, Ribbed Nut, Plastic Washer, Screw, Central Rod, Arm Light
Bulb, Light Cluster with Socket, Cup Large Ring, Crystal Clip and
Crystal.
Product Usage Instructions
- Open the box carefully and take out all the components, parts
bag and manual from the box. - Check all the components against the parts list and make sure
to get each part on the list. If any parts are missing or damaged,
contact the manufacturer at [email protected] to get a
replacement. Parts are not included for which is shown as 0 under
QTY. - Refer to the illustration provided in the manual while doing
assembly and follow the steps as below:- Assemble 3 arms(T) which ends with a tab onto the large ring(X)
using screws(R) and plastic washers(Q) from the inside and fix with
ribbed nuts(P) from the outside. Make sure the holes to hang the
crystals are facing down. - Assemble the top ends of 3 arms(T) onto the cup(W) using
screws(R) from the inside, fix with plastic washers(Q) and ribbed
nuts(P). The washers(Q) are used between the arm tops and cup to
prevent scratches during assembly. - Thread the bottom of central rod(S) onto the light cluster(V),
the top of rod(S) goes through the central hole of cup(W). - Assemble the components F, G, H, I, J onto L.
- Connect D and E to A.
- Connect B to K.
- Connect H, G, F to D.
- Connect Z and Y to X. Connect U to V. Connect GND to W.
- Assemble 3 arms(T) which ends with a tab onto the large ring(X)
Assembly & Installation Instructions
MODEL: 900017 900018
IMPORTANT SAFETY INSTRUCTIONS: · Warning: If any special control devices are used with this fixture, follow the instructions carefully to assure
full compliance with N.E.C. requirements. If there are any questions, please contact a qualified electric contractor. · Warning: This product can expose you to chemicals including lead, which is known to the State of California, to cause cancer or birth defects or other reproductive harm. For more information, please go to www.P65Warnings.ca.gov · Caution: Electrician installation is highly recommended. All glass is fragile, use care when handling glass component(s) and or lamp(s). Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.
Important Notice: This is a generic instruction sheet used for various fixtures. The shape and style of fixture / glass / shade / diffuser may vary.
(Required Supply Circuit: 120V, 60Hz. Watt: 3*E26*60W Max)
Compatible Bulb Type (NOT Included)
The mostly suggested bulb type is 11W LED A19 bulb
COMPONENTS INCLUDED IN THE PACKAGE Arm / Ring / Light Cluster / Crystal / Chain & Loops / Cup /
Canopy / Bracket with Nipple
Parts included in parts bag
ASSEMBLY & INSTALLATION STEPS: 1. Open the box from top, take out all the components, parts bag and manual from the box carefully.
2. Check all the components against the parts list. Make sure get each parts on list. If any parts missing or glass damage, please contact manufacturer at: [email protected] to get a replacement.
Parts are NOT included for which is shown as 0 under QTY.
Part Name Junction Box Leading Wires Wire Nut Mounting Bracket with Nipple Mounting Screw Canopy Hanging Loop Collar Chain Locker Chain Fixture Wire Loop Small Ring
QTY 0 0 3 1 3 1 1 1 2 1 2 1 1
Code A B C D E F G H I J K L M
PARTS LIST Part Name
Cap Hex Nut Ribbed Nut Plastic Washer Screw Central Rod Arm Light Bulb Light Cluster with Socket Cup Large Ring Crystal Clip Crystal
QTY 1 1 6 6 6 1 3 0 1 1 1 56 56
Code N O P Q R S T U V W X Y Z
3. Refer to the illustration while doing assembly and follow the steps as below: I Assemble 3 arms(T) which ends with a tab onto the large ring(X) using screws(R) and plastic washers(Q) from the
inside and fix with ribbed nuts(P) from the outside. Make sure the holes to hang the crystals are facing down. II Assemble the top ends of 3 arms(T) onto the cup(W) using screws(R) from the inside, fix with plastic washers (Q) and
ribbed nuts(P). The washers(Q) are used between the arm tops and cup to prevent scratches during assembly. III Thread the bottom of central rod(S) onto the light cluster(V), the top of rod(S) goes through the central hole of cup(W),
fix the rod with the hex nut(O). Slide on the cap(N), small ring(M), and fasten with the loop(L). Fixture wires(K) go through these parts at this step. IV Adjust the length of the chain to your desired hanging height. Thread to open the chain lockers (I) on the ends of the chain (J). Connect one end with loop (L) and fixture, connect the other end with canopy (F), then close the chain lockers. Wires (K) go through the hanging loop (G), collar (H) and canopy (F) for later wiring. V Install the mounting bracket with nipple (D) to the junction box (A) by the mounting screws (E). VI Connect wires according to the wiring diagram on the right. VII Thread the hanging loop (G) onto the nipple of mounting bracket (D) to hang the fixture. Thread the collar (H) to fix the canopy (F) onto the junction box. VIII Insert the crystal clips(Y) into the holes on the crystals(Z), and clip them to hold the crystals onto the large ring(X) tightly. Screw on the bulbs(U) to the socket(V).
Illustration of assembly and wiring:
I. R, Q, X
T, P
II. R, W, Q
T, P
III. L, M, N, O, X
S, V
IV. F, G, H, I, J
L
V. D, E
A
VI. B, K
C
VII. H, G, F
D
VIII.Z, Y
X; U
V
GND
W
A
B C D E F G H I JK I
L
M N O P
Q
R S
T
P
Q
X Y
R
U
Z V
P65Warnings.ca.gov
