W0433 Sloane 2 Light Vanity Satin Brass
Product Information
The product is a light fixture that requires assembly and
installation. It comes with a mounting plate unit, mounting screw,
wire connector, bolt nut, glass shade, and spare parts. The fixture
can hold two 10W Max. G9 LED bulbs (not included) and is covered
under a 1-year warranty.
Hardware Package (included)
- Mounting Plate Unit (A)
- Mounting Screw (B)
- Wire Connector (C)
- Bolt Nut (D)
- Outlet Box
- House Ground Wire
- Green Ground Screw
- Fixture Mounting Screw
- Fixture Ground Wire
- Fixture Wire
Spare Parts List
- Mounting Hardware 6642MM (1SET)
- Mounting Plate Unit (A)
- Mounting Screw (B)
- Wire Connector (C)
- Bolt Nut (D)
- Glass Shade 10354FG
Product Usage Instructions
- Before installing, consult local electrical codes for wiring
and grounding requirements. - Read and save the instructions.
- Turn off the power at the fuse or circuit box.
- Unscrew the two bolt nuts (D), remove the mounting plate unit
(A) from the backplate. - Attach the mounting plate unit (A) to the outlet box by using
two mounting screws (B). Make sure that two set holes are lined up
horizontally to make the fixture level. - Attach the backplate of the fixture to the mounting plate unit
(A) by aligning and inserting the two fixture mounting screws into
set holes on backplate, then secure it with two bolt nuts (D). - Install 2 x 10W Max. G9 LED bulbs (not included). Check
relamping label at socket area or packaging for maximum wattage
allowed. - Attach the glass shade to the fixture and secure them.
- Turn on the power at fuse or circuit box.
Note: The warranty does not cover damages caused by extreme acts
of nature, environmental conditions not suited for the product’s
intended use, operation in temperatures outside of the range
specified in the instruction manual, or usage with improper power
supply, power surges or dips. For coastal locations, some corrosion
is considered normal for the environment. If warranty service is
needed, contact Vaxcel at [email protected] or 1-800-482-9235.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
W0433
WARNING: TTOOAAVVOOIIDDRRIISSKKOOFF EELLEECTRICAL SHOCK, BE SURE TOO SSHHUUTTOOFFFF PPOOWWEERRBWEHFIOLREEININSTSATLALLILNIGNGORORSESREVRIVCICNIGNGTHTIHSIFSIXFTIXUTRUER. E.
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions.
Hardware Package (included):
Mounting Plate Unit (A)
Mounting Screw (B)
Wire Connector (C)
Bolt Nut (D)
Outlet Box
House Ground Wire Green Ground Screw Wire Connector (C) Mounting Plate Unit (A) Fixture Mounting Screw Mounting Screw (B) Fixture Ground Wire Fixture Wire Bolt Nut (D)
Installation Steps
Turn off the power at fuse or circuit box
1. Unscrew the two bolt nuts (D), remove the mounting plate unit (A) from the backplate.
2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Note: Make sure that two set holes are lined up horizontally to make the fixture level.
Backplate Bolt Nut (D)
Socket Max. 10W G9 LED bulb (not included)
Glass Shade
Page 1 / 2
230213
3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows: · Connect the hot wire (black insulation) from the fixture to the black wire from the power source. · Connect the neutral wire (white insulation) from the fixture to the white wire from the power source. · Attach the fixture ground wire (bare wire) to the mounting plate unit (A) with the green ground screw, then connect it to the house ground wire with the wire connector (C). Carefully put all of the wires back into the outlet box.
4. Attach the backplate of the fixture to the mounting plate unit (A) by aligning and inserting the two fixture mounting screws into set holes on backplate, then secure it with two bolt nuts (D).
5. Install 2 x 10W Max. G9 LED bulbs (not included). Check relamping label at socket area or packaging for maximum wattage allowed.
6. Attach the glass shade to the fixture, and secure them.
Turn on the power at fuse or circuit box
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Mounting Hardware 6642MM (1SET)
Mounting Plate Unit (A) Mounting Screw (B) Wire Connector (C) Bolt Nut (D)
Glass Shade 10354FG
A B
A: 7-3/4″ B: 16″ C: 8-3/4″ C
1 Year Warranty
Vaxcel warrants all of our products against defects in workmanship and finishes for one year following the date of shipment.
Exclusions: This warranty does not include the failure of products from extreme acts of nature; environmental conditions not suited for the products intended use; operation in temperatures outside of the range specified in the instruction manual; usage with improper power supply, power surges or dips. For coastal locations, some corrosion is considered normal for the environment.
Vaxcel reserves the right to repair, replace or issue a credit for any properly installed product, provided it is returned per RMA instruction. This warranty is limited to the cost of the product only and does not extend to transportation, installation or replacement costs.
How can warranty service be obtained? [email protected] 1-800-482-9235
Page 2 / 2
230213
