W0434 Sloane 3 Light Vanity Satin Brass Light
Product Information
The product in question is a light fixture with a glass shade
and a socket that supports a maximum of 10W G9 LED bulbs (not
included). The package includes a mounting plate unit, mounting
screws, wire connector, bolt nut, and spare parts. The fixture is
covered under a 1-year warranty from the date of shipment.
Product Usage Instructions
- Before starting the installation process, consult local
electrical codes for wiring and grounding requirements. - Read and save the instructions for future reference.
- Turn off the power at the fuse or circuit box.
- Unscrew the two bolt nuts (D) to remove the mounting plate unit
(A) from the backplate. - Attach the mounting plate unit (A) to the outlet box using two
mounting screws (B). Make sure that two set holes are lined up
horizontally to make the fixture level. - Attach the backplate of the fixture to the mounting plate unit
(A) by aligning and inserting the two fixture mounting screws into
set holes on the backplate, then secure it with two bolt nuts
(D). - Install 3 x 10W Max. G9 LED bulb (not included). Check
relamping label at socket area or packaging for maximum wattage
allowed. - Attach the glass shade to the fixture and secure them.
- Turn on the power at the fuse or circuit box.
Note: The product comes with spare parts that can be reordered
if damaged or missing. The warranty covers all defects in
workmanship and finishes for one year following the date of
shipment. However, it does not include failures due to extreme acts
of nature, usage with improper power supply, or operation in
temperatures outside of the range specified in the instruction
manual. For coastal locations, some corrosion is considered normal
for the environment. To obtain warranty service, contact Vaxcel
through email or phone.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
W0434
WARNING: TTOOAAVVOOIIDDRRIISSKKOOFF EELLEECTRICAL SHOCK, BE SURE TOO SSHHUUTTOOFFFF PPOOWWEERRBWEHFIOLREEININSTSATLALLILNIGNGORORSESREVRIVCICNIGNGTHTIHSIFSIXFTIXUTRUER. E.
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions.
Hardware Package (included):
Mounting Plate Unit (A)
Mounting Screw (B)
Wire Connector (C)
Bolt Nut (D)
Outlet Box
House Ground Wire Green Ground Screw Wire Connector (C) Mounting Plate Unit (A) Fixture Mounting Screw Mounting Screw (B) Fixture Ground Wire Fixture Wire
Installation Steps
Turn off the power at fuse or circuit box
1. Unscrew the two bolt nuts (D), remove the mounting plate unit (A) from the backplate.
2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Note: Make sure that two set holes are lined up horizontally to make the fixture level.
Backplate Bolt Nut (D)
Socket Max.10W G9 LED Bulb (not included)
Glass Shade
Page 1 / 2
230213
3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows: · Connect the hot wire (black insulation) from the fixture to the black wire from the power source. · Connect the neutral wire (white insulation) from the fixture to the white wire from the power source. · Attach the fixture ground wire (bare wire) to the mounting plate unit (A) with the green ground screw, then connect it to the house ground wire with the wire connector (C). Carefully put all of the wires back into the outlet box.
4. Attach the backplate of the fixture to the mounting plate unit (A) by aligning and inserting the two fixture mounting screws into set holes on backplate, then secure it with two bolt nuts (D).
5. Install 3 x 10W Max. G9 LED bulb (not included). Check relamping label at socket area or packaging for maximum wattage allowed.
6. Attach the glass shade to the fixture, and secure them.
Turn on the power at fuse or circuit box
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Mounting Hardware 6642MM (1SET)
Mounting Plate Unit (A) Mounting Screw (B) Wire Connector (C) Bolt Nut (D)
Glass Shade 10354FG
A B
A: 7-3/4″ B: 24″ C: 8-3/4″
C
1 Year Warranty
Vaxcel warrants all of our products against defects in workmanship and finishes for one year following the date of shipment.
Exclusions: This warranty does not include the failure of products from extreme acts of nature; environmental conditions not suited for the products intended use; operation in temperatures outside of the range specified in the instruction manual; usage with improper power supply, power surges or dips. For coastal locations, some corrosion is considered normal for the environment.
Vaxcel reserves the right to repair, replace or issue a credit for any properly installed product, provided it is returned per RMA instruction. This warranty is limited to the cost of the product only and does not extend to transportation, installation or replacement costs.
How can warranty service be obtained? [email protected] 1-800-482-9235
Page 2 / 2
230213
