Veneta N301246 Cordless Roller Shade Instruction Manual

N301246 Cordless Roller Shade

Product Information: N301246 Cordless Roller Shade

The N301246 Cordless Roller Shade is a window treatment solution
that offers ease of installation and removal. It comes with shade
brackets, mounting brackets, mid-mounting brackets, and hardware
for installing the shade with a raceway system. The product also
includes a handle for cordless shades for easy operation.

The recommended tools for installation are a screw gun/drill,
tape measure, screwdriver, level, and pencil. The package includes
1 1/4 hexagon screws needed for installing the hardware.

Product Usage Instructions:

Shade Bracket Installation:

Before installing the shade bracket, ensure that the space
between each mounting bracket is divided evenly. Use the
recommended tools to install the shade bracket.

Shade Installation and Removal:

1. Insert the Clutch end into the tongue of the clutch
   bracket.
2. Press the end plug and insert the End Plug end into the hole of
   the bracket of the other side.
3. Attach bracket covers to brackets and locate the pin to join
   the bracket pieces and the shade.
4. To remove the shade, push the lock pin on the end plug bracket
   upward and draw back the end plug from the bracket.

Installation of Roller Shade with Raceway System (Outside
Mount):

1. Attach the end brackets and extensions into the two ends of the
   raceway.
2. Ensure that the extension bolt locks into the raceway’s
   dedicated hole.
3. For shade with width > 40, attach the mid-mounting bracket
   to the shade before installing shade brackets on raceway ends.
4. Install the raceway onto the window opening, ensuring that the
   top of each mounting bracket is parallel with the edge of the
   window frame.
5. The distance from the shade bracket’s mounting holes to the
   front edge of the window frame should be at least 3/4.
6. Ensure that all the shade brackets are level and aligned with
   each other.
7. Each shade bracket will require two 1 1/4 hexagon screws for
   installation.

Shade Installation Tips:

After installing the shade into the shade brackets, use a level
to check if the tube of the shade is horizontal. If not, adjust the
position of the shade brackets to keep the tube level.

Handle Installation:

1. Attach the handle to the hem bar by aligning the center of the
   bottom of the handle with the label attached at the center of the
   hem bar.
2. Hook the handle to the hem bar from top to bottom.
3. Press the handle from top to bottom to make the top of the
   handle clip into the hem bar.

N301246 Cordless Roller Shade Installation Instruction
With Raceway Recommended Tools Screw gun / Drill Tape Measure Screwdriver Level Pencil

Shade Bracket Installation
Installation of Roller Shade with Raceway System (Inside Mount) Attach the shade brackets and extensions into the two ends of the raceway. Make sure the extension bolt locks into the raceway’s dedicated hole. Install the shade and raceway system into the window opening. It is better to screw the middle holes on raceway to make sure the raceway location can be adjusted to left or right, after the raceway has been located at proper position, and then screw other screw holes. Taking care that the distance between the 1st screw and the window edge is at least 3/4″.

The space between each mounting bracket should be divided evenly as pictured.
Shade Installation and Removal
First, insert the Clutch end into the tongue of clutch bracket Second, press the end plug and insert the End Plug end into the
hole of bracket of the other side. And then attach bracket covers to brackets and locate the pin. As
shown below:

Hardware Included

1Screws needed for installing

Hardware

Drawing

1 1/4″ Hexagon screw

Usage To install bracket

2Hardware for Roller shade with Raceway System

Hardware

Drawing

Usage

Shade bracket (for flush
inside mount)

To install shade (on Clutch end)
To install shade (on End Plug end)

Mounting bracket
(for outside mount)
Mid Mounting Bracket
(for outside mount)
Shade bracket cover

To install Raceway (on Clutch end)
To install shade (on End Plug end)
As support for Raceway when needed. 1 Mid mounting bracket should be attached to the shade when width > 40″
Bracket cover

Handle

For Cordless Shades

Installation of Roller Shade with Raceway System(Outside Mount) Like inside mount, firstly attach the end brackets and extensions into the two ends of the raceway. Make sure the extension bolt locks into the raceway’s dedicated hole.
For shade with width>40″, make sure the top groove of the mid mounting bracket hook onto the top of the raceway while the bracket’s bottom groove clips into the bottom rib of the raceway, as shown below. Middle brackets should be installed before shade brackets on raceway ends.
Middle Mounting Bracket
When installing the raceway onto the window opening, the top of each mounting bracket needs to be parallel with the edge of the window frame. The distance from the shade bracket’s mounting holes to the front edge of the window frame should be at least 3/4″. Make sure all the shade brackets are level and aligned with each other. Each shade bracket will require two 1 1/4″ hexagon screws for the installation.

Align Clutch end and Tension Dial end of the shade with the tongue of the clutch bracket

The bracket covers must be attached to the bracket to prevent the shade from falling. Locate the pin, which can be found on the bracket cover, and use it to join the bracket pieces and the shade.

Finally, remove the paper band from the shade by hand.
Shade Installation Tips: After shade is installed into shade brackets, use a Level to check if the tube of shade is horizontal; if not, please adjust the position of shade brackets to keep the tube level.

Removal of Roller Shade with Raceway System Use a tool to push the lock pin on end plug bracket upward Use tool to draw back the end plug from bracket Finally remove shade from mounting bracket. As shown drawing

How to install or remove Handle for Cordless Shade
Attach Handle to Hem Bar
Turn over hem bar and you can see a label attached at the center of hem bar. Align the center of the bottom of handle with the label and hook the handle to the hem bar from top to bottom.
Press the handle from top to bottom to make the top of handle clip into the hem bar.
Finally tear off the label from hem bar.
Label

3/4″

Before the pin is located

After the pin is located

The center of handle should be aligned with the label.
1

Roller Shade Operation

Cordless Operation

The tension in our cordless roller shades can be adjusted to provide optimal light control and to ensure easy and dependable operation on a variety of window types and sizes. If a cordless shade has been tending to slide down on its own or it fails to roll up, the issue can be easily fixed by turning the adjustment dial towards “+” to increase the tension. Conversely, if the cordless shade cannot stop at the desired height and tends to roll up by itself, the tension can be decreased by turning the adjustment dial towards the “-“.

Remove handle from hem bar
Use straight screwdriver to pry the bottom of Handle from hem bar and then handle can be removed.

Pull the handle downwards or upwards and the shade will be lowered or raised.

*The blind must be installed on the brackets when adjusting.

N301246
2