N301078-2 Natural Cordless Roller Shade
N301078-2 Cordless Roller Shade
The N301078-2 Cordless Roller Shade is a window shade that can
be easily installed without the need for cords or chains. It comes
with a raceway system that allows for both inside and outside
mounting options. The product comes with the necessary hardware and
tools for installation.
Recommended Tools
- Screw gun / Drill
- Tape Measure
- Screwdriver
- Level
- Pencil
Shade Bracket Installation
The space between each mounting bracket should be divided
evenly. Use a level to ensure that the tube of shade is horizontal.
Adjust the position of shade brackets if necessary to keep the tube
level.
Shade Installation and Removal
- Insert the Clutch end into the tongue of the clutch
bracket. - Press the end plug and insert the End Plug end into the hole of
bracket of the other side. - Attach bracket covers to brackets and locate the pin.
- Remove the paper band from the shade by hand.
Shade Installation Tips:
After shade is installed into shade brackets, use a Level to
check if the tube of shade is horizontal; if not, please adjust the
position of shade brackets to keep the tube level.
Hardware Included
- 1 1/4 Hexagon screw – To install bracket
- Shade bracket (for flush inside mount) – To install shade (on
Clutch end) - Shade bracket (for flush inside mount) – To install shade (on
End Plug end) - Mounting bracket (for outside mount) – To install shade (on
Clutch end) - Mounting bracket (for outside mount) – To install shade (on End
Plug end) - Mid Mounting Bracket (for outside mount) – As support for
Raceway when needed. 1 Mid mounting bracket should be attached to
the shade when width > 40 - Shade bracket cover – To install Valance (mounted on
raceway) - Valance bracket – To install Valance (placed on Valance)
- Valance clip – To install Valance (placed on Valance)
Installation of Roller Shade with Raceway System(Outside
Mount)
Attach the end brackets and extensions into the two ends of the
raceway. Make sure the extension bolt locks into the raceway’s
dedicated hole. For shade with width > 40, make sure the top
groove of the mid mounting bracket hook onto the top of the raceway
while the bracket’s bottom groove clips into the bottom rib of the
raceway. Middle brackets should be installed before shade brackets
on raceway ends. When installing the raceway onto the window
opening, the top of each mounting bracket needs to be parallel with
the edge of the window frame. The distance from the shade bracket’s
mounting holes to the front edge of the window frame should be at
least 3/4. Make sure all the shade brackets are level and aligned
with each other. Each shade bracket will require two 1 1/4 hexagon
screws for the installation.
Fabric Valance Installation
Valance Bracket Installation
Insert the handle into the valance bracket. For Cordless Shades,
make sure the handle is inserted into the correct slot. Before
installing the bracket, make sure the pin is located on the
bracket. After installation, attach the valance to the bracket by
sliding it into place.
Valance Clip Installation
Insert the valance clip into the dedicated groove on the
aluminum strip, paying special attention to the direction of the
valance clip. For a valance, the valance clip should face
downwards. For valance, it should face up. The valance clip
location should align with the valance bracket.
Removal of Roller Shade with Raceway System
- Use a tool to push the lock pin on end plug bracket
upward. - Use a tool to draw back the end plug from bracket.
- Finally remove shade from mounting bracket.
N301078-2 Cordless Roller Shade Installation Instruction
With Raceway Recommended Tools Screw gun / Drill Tape Measure Screwdriver Level Pencil
Shade Bracket Installation
Installation of Roller Shade with Raceway System (Inside Mount) Attach the shade brackets and extensions into the two ends of the raceway. Make sure the extension bolt locks into the raceway’s dedicated hole. Install the shade and raceway system into the window opening. It is better to screw the middle holes on raceway to make sure the raceway location can be adjusted to left or right, after the raceway has been located at proper position, and then screw other screw holes. Taking care that the distance between the 1st screw and the window edge is at least 3/4″.
The space between each mounting bracket should be divided evenly as pictured.
Shade Installation and Removal
First, insert the Clutch end into the tongue of clutch bracket Second, press the end plug and insert the End Plug end into the
hole of bracket of the other side. And then attach bracket covers to brackets and locate the pin. As
shown below:
4 Finally, remove the paper band from the shade by hand.
Shade Installation Tips: After shade is installed into shade brackets, use a Level to check if the tube of shade is horizontal; if not, please adjust the position of shade brackets to keep the tube level.
Hardware Included
1Screws needed for installing
Hardware
Drawing
1 1/4″ Hexagon screw
Usage To install bracket
2Hardware for Roller shade with Raceway System
Hardware
Drawing
Usage
Shade bracket (for flush
inside mount)
To install shade (on Clutch end)
To install shade (on End Plug end)
Mounting bracket
(for outside mount)
Mid Mounting Bracket
(for outside mount)
Shade bracket cover
Valance bracket
To install Raceway (on Clutch end)
To install shade (on End Plug end)
As support for Raceway when needed. 1 Mid mounting bracket should be attached to the shade when width > 40″
Bracket cover
To install Valance (mounted on raceway)
Valance clip
To install Valance (placed on Valance)
Installation of Roller Shade with Raceway System(Outside Mount) Like inside mount, firstly attach the end brackets and extensions into the two ends of the raceway. Make sure the extension bolt locks into the raceway’s dedicated hole.
For shade with width>40″, make sure the top groove of the mid mounting bracket hook onto the top of the raceway while the bracket’s bottom groove clips into the bottom rib of the raceway, as shown below. Middle brackets should be installed before shade brackets on raceway ends.
Middle Mounting Bracket
When installing the raceway onto the window opening, the top of each mounting bracket needs to be parallel with the edge of the window frame. The distance from the shade bracket’s mounting holes to the front edge of the window frame should be at least 3/4″. Make sure all the shade brackets are level and aligned with each other. Each shade bracket will require two 1 1/4″ hexagon screws for the installation.
Align Clutch end and Tension Dial end of the shade with the tongue of the clutch bracket
The bracket covers must be attached to the bracket to prevent the shade from falling. Locate the pin, which can be found on the bracket cover, and use it to join the bracket pieces and the shade.
Removal of Roller Shade with Raceway System Use a tool to push the lock pin on end plug bracket upward Use tool to draw back the end plug from bracket Finally remove shade from mounting bracket. As shown drawing
Fabric Valance Installation
Valance Bracket Installation
After installing the shade and raceway, the brackets for the valance come next. When installing the valance brackets, the mounting brackets must be avoided. Align the valance bracket with the raceway first and then push the bracket onto the raceway. The top groove of the valance bracket should hook onto the top of the raceway while the bracket’s bottom groove clips into the bottom rib of the raceway, as shown below. The drawing below shows the valance brackets installed in an ideal position. They are placed far enough apart so that the space is divided evenly, and without interference from the mounting brackets. If the mounting bracket’s location conflicts with that of the valance bracket, the valance bracket location should have an offset of 50mm to avoid interference.
Handle
For Cordless Shades
3/4″
Before the pin is located
After the pin is located
1
Valance Clip Installation Insert the valance clip into the dedicated groove on the aluminum strip, paying special attention to the direction the valance clip. For a valance, the valance clip should face downwards. For valance, it should face up. The valance clip location should align with the valance bracket as pictured below.
The direction of this valance clip is facing downward
How to install or remove Handle for Cordless Shade
Attach Handle to Hem Bar
Turn over hem bar and you can see a label attached at the center of hem bar. Align the center of the bottom of handle with the label and hook the handle to the hem bar from top to bottom.
Press the handle from top to bottom to make the top of handle clip into the hem bar.
Finally tear off the label from hem bar.
Label
Roller Shade Operation
Cordless Operation
The tension in our cordless roller shades can be adjusted to provide optimal light control and to ensure easy and dependable operation on a variety of window types and sizes. If a cordless shade has been tending to slide down on its own or it fails to roll up, the issue can be easily fixed by turning the adjustment dial towards “+” to increase the tension. Conversely, if the cordless shade cannot stop at the desired height and tends to roll up by itself, the tension can be decreased by turning the adjustment dial towards the “-“.
Attach Valance to Raceway
Slide the valance clips to a position on the valance so that they are each aligned with a valance bracket on the raceway, and then push the valance clips into the valance bracket.
Valance Removal
First, remove Valance together with valance clip from valance bracket.
Take down shade from mounting bracket before removing valance Bracket from raceway Turn the valance bracket 90 degree then take off valance bracket from raceway, as shown below
The center of handle should be aligned with the label.
Pull the handle downwards or upwards and the shade will be lowered or raised.
*The blind must be installed on the brackets when adjusting.
Note: The installation & removal for all valances are the same.
Remove handle from hem bar
Use straight screwdriver to pry the bottom of Handle from hem bar and then handle can be removed.
N301078-2 2
