Surenoo Srg1010a-1024600 Series Rgb Interface Tft Lcd Module User Manual (+ PDF)

The SRG1010AA3-1024600 series RGB Interface TFT LCD Module can
be used for various applications that require a high-quality
display with a large viewing area. The module comes with a 24bit
Parallel RGB interface and supports up to 16.7M colors.

Before using the module, please refer to the Reference
Controller Datasheet and RGB Interface LCD Module Selection Guide
available on the manufacturer’s website.

When using the module, make sure to follow the Power On/Off
Sequence provided in the user manual to prevent any damage to the
product. The module has a digital operating voltage of 3.0 to 3.6V
and an Analog Supply Voltage of 9.4 to 9.8V. The backlight has a
forward voltage of 8.4 to 9.6V and a forward current of 260mA.

Please note that the module has Absolute Maximum Ratings, which
means that it can withstand short-term usage, not exceeding 120
hours. Long-term usage under these conditions may lead to a shorter
lifespan of the product.

View Fullscreen

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

SRG1010A-1024600 Series
RGB Interface TFT LCD Module USER MANUAL
Please click the following image to buy the sample

6KHQ¼KHQ6XUHQRR7HFKQR¹RJ»&R/WG ºººVXUHQRRFRP 6¸»SH·6X UHQRR

Reference Controller Datasheet

RGB Interface LCD Module Selection Guide

www.surenoo.com

P 01

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

CONTENTS
1GENERAL INFORMATION 2EXTERNAL DIMENSIONS 3ABSOLUTE MAXIMUM RATINGS 4ELECTRICAL CHARACTERISTICS 5BACKLIGHT CHARACTERISTICS 6CTP CHARACTERISTICS 7ELECTRO-OPTICAL CHARACTERISTICS 8INTERFACE DESCRIPTION 9INPUT TIMING 10POWER ON/OFF SEQUENCE 11RELIABILITY TEST CONDITIONS 12INSPECTION CRITERION

www.surenoo.com

P 02

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

1GENERAL INFORMATION
Item of general information LCD Display Size (Diagonal)
LCD Display Type LCD Display Mode Recommended Viewing Direction Gray inversion Direction Module size (W×H×T) Active area (W×H) Number of pixels (Resolution) Pixel pitch (W×H) Color Pixel Arrangement
CTP Driver IC Interface Type Power consumption Color Numbers Backlight Type

Contents 10.1
TFT/TRANSMISSIVE Normally White 12 6
235.00×143.00×5.15 222.72×125.28 1024RGB×600 0.2175×0.2088 RGB Stripe GT9271
24bit Parallel RGB interface –
16.7M White LED

Unit inch
o’clock o’clock mm mm pixel mm mA –

www.surenoo.com

P 03

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

2EXTERNAL DIMENSIONS

Model No.: SRG1010AA3-1024600

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

www.surenoo.com

P 04

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

3ABSOLUTE MAXIMUM RATINGS

Parameter of absolute

Symbol

Min

maximum ratings

Max

Unit

VDD

-0.3

AVDD

-0.5

Power voltage

VGH

-0.3

VGL

-20

0.3

VGH-VGL

-0.3

Operating temperature

Top

-20

Storage temperature

Tst

-30

Humidity

–

90%(Max 60) RH

Note: Absolute maximum ratings means the product can withstand short-term, not more than

120 hours. If it is a long time to withstand these conditions, the life time would be shorter.

www.surenoo.com

P 05

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

4ELECTRICAL CHARACTERISTICS(DC CHARACTERISTICS)

Parameter of DC characteristics

Symbol

Min.

Typ.

Max. Unit

Digital operating voltage

VDD

3.0

3.3

3.6

Analog Supply Voltage

AVDD

9.4

9.6

9.8

Gate On Voltage

VGH

Gate Off Voltage

VGL

-6.6

-6

-5.4

Common Voltage

VCOM

3.5

3.6

3.7

Input voltage `H’ level

VIH 0.8*VDD

–

VDD

Input voltage `L’ level

VIL

VSS

–

0.2*VDD V

Output voltage `H’ level

VOH VDD-0.4

–

VDD

Output voltage `L’ level

VOL

VSS

–

VSS+0.4 V

Digital current

I VDD

—

Analog current

I AVDD

—

Gate On current

I VGH

—

0.5

Gate Off current

I VGL

—

0.5

Note 1: Please adjust VCOM voltage to make the flicker level be minimum.

www.surenoo.com

P 06

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

5BACKLIGHT CHARACTERISTICS

Item of backlight characteristics

Symbol Min.

Typ.

Max. Unit Remark

Forward Voltage

Vf 8.4

9.0

9.6

Note1

Forward Current

–

260

–

Number of LED

–

3*13=39

–

Piece

–

LED Connection mode P/S

– Serial/Parallel –

–

Lifetime of LED

–

10000

–

hour Note2

Note: Note1: The LED Supply Voltage is defined by the number of LED at Ta=25 and

If=260mA. Note2: The LED lifetime define as the estimated time to 50% degradation of initial

luminous. The LED lifetime could be decreased if operating If is larger than 260mA. Backlight circuit:

www.surenoo.com

P 07

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

6CTP CHARACTERISTICS

Item of CTP characteristics

Specification

Panel Type

Glass Cover + Glass Sensor

Resolution

1024 × 600

Surface Hardness

Transparency

82%

Driver IC

GT9271

Interface Type

I2C

Support Points

Sampling Rate

20~100

Supply voltage

3.3

Model No.: SRG1010AA3-1024600

Unit

Remark

–

pixel

–

www.surenoo.com

P 08

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

7ELECTRO-OPTICAL CHARACTERISTICS

Item of

electro-optical Symbol Condition Min. Typ. Max. Unit Remark Note

characteristics

Response time Contrast Ratio

Tr+Tf CR

=0 =0

–

20 40 ms FIG 1.

–

350

–

FIG 2.

Luminance uniformity WHITE Ta=25

–

FIG 2.

Surface Luminance

–

300

– cd/m2 FIG 2.

CIE (x, y) chromaticity

White

White x White y

=0 =0
Ta=25

0.273 0.313 0.353 0.289 0.329 0.369

–

FIG 2.

=90(12 o’clock)

50 60

–

deg

Viewing =270(6 o’clock) angle range =0(3 o’clock)

CR 10

50 60

60 70

–

deg FIG 3.
deg

=180(9 o’clock)

60 70

–

deg

NTSC ratio

–

Note 1. Contrast Ratio(CR) is defined mathematically by the following formula. For more

information see FIG 2.:

Note 2. Surface luminance is the LCD surface from the surface with all pixels displaying white. For more information see FIG 2.
Lv=Average Surface Luminance with all white pixels (P1,P2,P3,P4,P5,P6,P7,P8,P9) Note 3. The uniformity in surface luminanceWHITEis determined by measuring luminance at each test position 1 through 9, and then dividing the maximum luminance of 9points luminance by minimum luminance of 9 points luminance. For more information see FIG 2.

www.surenoo.com

P 09

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

Note 4. Response time is the time required for the display to transition from White to black(Rise Time, Tr) and from black to white(Decay Time, Tf). For additional information see FIG 1. Note 5. CIE (x, y) chromaticity ,The x,y value is determined by screen active area position 5. For more information see FIG 2. Note 6. Viewing angle is the angle at which the contrast ratio is greater than a specific value. For TFT module, the specific value of contrast ratio is 10.The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG 3. Note 7. For Viewing angle and response time testing, the testing data is base on Autronic-Melchers’s ConoScope. Series Instruments. For contrast ratio, Surface Luminance, Luminance uniformity and CIEthe testing data is base on BM-7 photo detector. Note 8. For TN type TFT transmissive module, Gray scale reverse occurs in the direction of panel viewing angle. FIG.1. The definition of Response Time

www.surenoo.com

P 10

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

FIG.2. Measuring method for Contrast ratio, surface luminance, Luminance
uniformity, CIE (x , y) chromaticity
A : H/6 ; B : V/6 ; H,V : Active Area(AA) size Measurement instrument: BM-7; Light spot size=5mm, 350mm distance from the LCD surface to detector lens.

FIG.3. The definition of viewing angle

www.surenoo.com

P 11

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

8INTERFACE DESCRIPTION

NO. Symbol

I/O

DESCRIPTION

1~2 VCC5V Power supply

Module Power supply(5V Typ.)

3~10 R0~R7

8bit digital Red data input(R0:LSB; R7:MSB)

GND

Power supply

Power ground

12~19 G0~G7

8bit digital Green data input(G0:LSB; G7:MSB)

GND

Power supply

Power ground

21~28 B0~B7

8bit digital Blue data input(B0:LSB; B7:MSB)

GND

Power supply

Power ground

DCLK

Clock signal. Latching data at the rising edge.

31 HSYNC

Horizontal Sync input. Negative polarity.

32 VSYNC

Vertical Sync input. Negative polarity.

DEN

Data input Enable. Active high to enable the data input Bus.

34 BL_CTRL

Backlight control pin

35 CTP_RST

CTP external reset signal, Low is active

36 CTP_SDA

I/O

CTP I2C data input and output

–

No connection

38 CTP_SCL

CTP I2C clock input

39 CTP_INT

CTP External interrupt to the host

40 LCD_RST

LCD RESET signal, Low is active

www.surenoo.com

P 12

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

9INPUT TIMING
Parameter
DCLK frequency@ Frame rate=60Hz Horizontal display area 1 Horizontal Line HSYNC pulse width
HSYNC Back Porch(Blanking) HSYNC Front Porch Vertical display area VSYNC period time VSYNC pulse width
VSYNC Back Porch(Blanking) VSYNC Front Porch

Symbol
DCLK thd th thpw thb thfp tvd tv tvpw tvb tvfp

Min.
45
1324 1
160 16
624 1 23 1

Value Typ.
51.2 1024 1344
160 160 600 635
23 12

Max.
57
1364 140 160 216
750 20 23 127

Unit
MHz DCLK
DCLK DCLK DCLK DCLK
H
H H H H

www.surenoo.com

P 13

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

10POWER ON/OFF SEQUENCE
Power On: VDDAVDD/VGLVGHVideo & Logic Signal Power Off: Video & Logic SignalVGHAVDD/VGLVDD

www.surenoo.com

P 14

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

11RELIABILITY TEST CONDITIONS

No.

Test Item

Test Condition

1 High Temperature Storage

80/120 hours

Low Temperature Storage

-30/120 hours

3 High Temperature Operating

70/120 hours

4 Low Temperature Operating

-20/120 hours

5 Temperature Cycle Storage -20(30min.)~25(5min.)~70(30min.)×10cycles

AInspection after test:

Inspection after 2~4 hours storage at room temperature, the sample shall be free from

defects: Air bubble in the LCD;

Sealleak;

Non-display; Missing segments;

Glass crack;

Current is twice higher than initial value.

BRemark:

The test samples should be applied to only one test item.

Sample size for each test item is 5~10pcs. Failure Judgment Criterion: Basic Specification, Electrical Characteristic, Mechanical

Characteristic, Optical Characteristic.

www.surenoo.com

P 15

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

12INSPECTION CRITERION
This specification is made to be used as the standard of acceptance/rejection criteria for TFT-LCD/IPS TFT-LCD module product, and this specification is applicable only in the case that the size of module equal to or exceed than 3.5 inch. 12.1 Sample plan Sampling plan according to GB/T2828.1-2003/ISO 2859-11999 and ANSI/ASQC Z1.4-1993,normal level 2 and based on: Major defect: AQL 0.65 Minor defect: AQL 1.5 12.2 Inspection condition Viewing distance for cosmetic inspection is about 30cm with bare eyes, and under an environment of 20~40W light intensity, all directions for inspecting the sample should be within 45°against perpendicular line. (Normal temperature 20~25and normal humidity 60 ±15%RH ) 12.3 Definition of Inspection Item. ADefinition of inspection zone in LCD.

Zone A: character/Digit area

www.surenoo.com

P 16

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

Zone B: viewing area except Zone A (Zone A + Zone B=minimum Viewing area)

Zone C: Outside viewing area (invisible area after assembly in customer’s product)

Fig.1 Inspection zones in an LCD

Note: As a general rule, visual defects in Zone C are permissible, when it is no trouble for

quality and assembly of customer’s product. BDefinition of some visual defect

Because of losing all or part function, bad pixel dots appear bright and the

Bright dot size is more than 50% of one dot in which LCD panel is displaying under

black pattern.

Dark dot

Dots appear dark and unchanged in size in which LCD panel is displaying under pure red, green, blue picture, or pure whiter picture.

12.4 Major Defect

Item No.

Items to be inspected

Inspection standard

Classification of defects

1) No display

2) Display abnormally

3) Missing vertical, horizontal segment

Functional defects 4) Short circuit

5) Excess power consumption 6)Backlight no lighting, flickering and abnormal

major

lighting

Missing

Missing component

Overall outline dimension beyond the drawing is not

Outline dimension

allowed

www.surenoo.com

P 17

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

12.5 Minor Defect

Item Items to be No. inspected

Inspection standard

Classification of defects

Zone

Acceptable Qty

A+B

3.57″ 710.1″ 10.1″

Bright pixel dot

Acceptable

Bright dot

Dark pixel dot

/dark dot

2bright dots adjacent

defect

2dark dots adjacent

Minor

Total bright and dark dots 5

Note: Minimum distance between defective dots is more than 5mm;

Pixel dots’ function is normal, but bright dots caused by foreign

material and other reasons are judged by the dot defect of 5.2.

Zone

Acceptable Qty

A+B

Size(mm)
0.2

3.5″7″

710.1″

10.1″

Acceptable Acceptable Acceptable

Acceptable

0.20.5

Minor

0.5

Note: 1. Minimum distance between defective dots is more than 5 mm; 2. The quantity of defect is zero in operating condition.

Zone

Acceptable Qty

Size (mm)

A+B

Linear

Length Width 3.5″7″

710.1″

10.1″

Minor

defect

Ignore W0.05 Acceptable Acceptable Acceptable

Acceptable

L5.0 0.05

W0.1

L5.0 W0.1

www.surenoo.com

P 18

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

5.4.1 Polarizer Position

( i) Shifting in position should not exceed the glass outline

dimension.

( ii ) Incomplete covering of the viewing area due to shifting is not

allowed.

5.4.2 Dirt on polarizer

Dirt which can be wiped easily should be acceptable.

5.4.3 Polarizer Dent & Air bubble

Zone

Acceptable Qty

A+B

Size(mm)

3.5″7″

710.1″

10.1″

0.2

Acceptable Acceptable Acceptable

Acceptable

0.20.5

Polarizer

0.5

defect

5.4.4 Polarizer scratch

Minor

(i) If the polarizer scratch can be seen after cover assembling

or in the operating condition, judge by the linear defect of 5.3.

( ii )If the polarizer scratch can be seen only in non-operating

condition or some special angle, judge by the following:

Zone

Acceptable Qty

Size (mm)
Length Width

3.5″7″

A+B
710.1″

10.1″

Acceptable

Ignore W0.05 Acceptable Acceptable Acceptable

1.0L 0.05

5.0 W0.20

L5.0 W0.2

MURA

Using 3% ND filter, it’s NG if it can be seen in R,G,B picture.

White/Black dotMURA

Visible underND3%D0.15mm, Acceptable 0.15mm<D0.5mm, N4D>0.5mm, Not allowable.

Minor

www.surenoo.com

P 19

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

(i) Crack Cracks are not allowed.
(ii) TFT chips on corner

Model No.: SRG1010AA3-1024600 Minor

Minor

Glass 6

Acceptable

defect

3.0

Not more than the

thickness of glass

Chips on the corner of terminal shall not be allowed to extend

into the ITO pad or expose perimeter seal.

(iii) Usual surface crack

Acceptable

1.5

Not more than the thickness of glass

It is only applicable to the upper glass of LCD.

Minor

www.surenoo.com

P 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

Model No.: SRG1010AA3-1024600

12.6 Module Cosmetic Criteria

Item No.
1 2
3
4 5 6
7
8 9 10

Items to be inspected
Difference in Spec. Pattern peeling
Soldering defects
Resist flaw on PCB FPC gold finger Backlight plastic frame
Marking printing effect Accretion of metallic Foreign matter Stain Plate discoloring

Inspection Standard
Not allowable No substrate pattern peeling and floating No soldering missing No soldering bridge No cold soldering Visible copper foil (0.5 mm or more) on substrate pattern is not allowed No dirt, breaking, oxidation lead to black No deformation, crack, breaking, backlight positioning column breaking, obvious nick. No dark marking, incomplete, deformation lead to unable to judge
No accretion of metallic foreign matter (Not exceed 0.2mm)
No stain to spoil cosmetic badly No plate fading, rusting and discoloring

Classification of defects
Major Major Major Major Minor
Minor
Major
Minor
Minor
Minor
Minor Minor

1. Lead parts

a. Soldering side of PCB Solder to form a `Filet’ all around the lead. Solder should not hide the lead form perfectly.
b. Components side(In case of `Through Hole PCB’) Solder to reach the Components side of PCB.

Minor Minor

2. Flat packages

Either `Toe'(A) or `Seal'(B)of the lead to be covered by “Filet”. Lead form to be assume over Solder.

Minor

11 3. Chips

(3/2) H h (1/2) H

Minor

4. Solder ball/Solder splash

a. The spacing between solder ball and the conductor or solder pad h 0.13 mm. The diameter of solder ball d0.15 mm.
b. The quantity of solder balls or solder splashes isn’t beyond 5 in 600 mm2. c. Solder balls/Solder splashes do not violate minimum electrical clearance.

Minor Minor Major

www.surenoo.com

P 21