SPB57T 57kg Tow Behind Broadcast Spreader
Product Information:
Product Name: 57KG Tow Behind Broadcast Spreader
Model No: SPB57T
Capacity (Volume): 60L
Capacity (Weight): 57kg
Dimensions (W x D x H): 680 x 980 x 790mm
Spread: 3-3.6m
Product Usage Instructions:
- Ensure that the spreader is in sound condition and good working
order before use. - Ensure that the operator is fully trained and competent to
operate the prime mover before attaching and using the
spreader. - Adhere to all chemical safety instructions when handling
products for use in the spreader. Personal safety equipment is
available from your Sealey stockist. - Always distribute the load evenly.
- Keep all non-essential personnel at a safe distance when the
spreader is in use. - Replace or repair damaged parts using recommended parts only.
Unauthorised parts may be dangerous and will invalidate the
warranty. - Avoid placing hands and feet near moving parts.
- Do not overload the spreader. Refer to the specification for
weight capacity. - Do not leave the spreader unattended, especially when loaded,
unless the wheels are chocked or the spreader is otherwise
secured. - Do not allow others to ride on the spreader.
- Do not allow untrained personnel to use the spreader.
- Use the spreader only for its intended purpose.
- Do not operate the spreader when you are tired or under the
influence of alcohol, drugs, or intoxicating medicines. - When loaded, avoid operating the spreader over edges or rough
surfaces where it may overturn.
WARNING: Failure to comply with these
instructions may result in damage to the spreader or other property
and/or personal injury.
57KG TOW BEHIND BROADCAST SPREADER MODEL NO: SPB57T
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction
manual
1. SAFETY
9
Ensure that the spreader is in sound condition and good working order before use.
9
Ensure that the operator is fully trained and competent to operate the prime mover before attaching and using the spreader.
9
Ensure that all chemical safety instructions are adhered to when handling products for use in the spreader. A full range of personal
safety equipment is available from your Sealey stockist.
9
Always distribute the load evenly.
9
Ensure all non essential personnel keep a safe distance when the spreader is in use.
9
Replace or repair damaged parts. Use only recommended parts. Unauthorised parts may be dangerous and will invalidate the
warranty.
9
Keep hands and feet away from moving parts.
8
DO NOT overload the spreader – see Specification.
8
DO NOT leave unattended, especially when loaded, unless the wheels are chocked or the spreader is otherwise secured.
8
DO NOT allow others to ride on the spreader.
8
DO NOT allow untrained personnel to use the spreader.
8
DO NOT use the spreader for purposes other than for which it is designed.
8
DO NOT operate the spreader when you are tired or under the influence of alcohol, drugs or intoxicating medicines.
8
When loaded, DO NOT operate the spreader over edges, rough surfaces etc. where the spreader is at risk of overturning.
WARNING! Failure to comply with these instructions may result in damage to spreader or other property and/or personal injury.
2. INTRODUCTION
Manufactured with a strong tubular steel frame and polypropylene dispensing hopper. Pin hitch design attaches to ride-on lawnmowers, can be converted to ball hitch using Model No. TB36*. Fitted with aluminium gear, rain cover, pneumatic tyres and adjustable feed system. Includes hopper screen to ease spreader flow and filter out unwanted contaminants. Sprays in 360° motion to cover a large area. Suitable for a variety of horticultural agents including grit, seed, salt, fertilizer and weedkiller.
fig.1
3. SPECIFICATION
Model No:………………………………………………………..SPB57T Capacity (Volume):………………………………………………….. 60L Capacity (Weight):…………………………………………………. 57kg Dimensions (W x D x H): …………………….680 x 980 x 790mm Spread: ……………………………………………………………..3-3.6m
© Jack Sealey Limited
Original Language Version
SPB57T Issue 5 14/04/23
4. ASSEMBLY & INSTALLATION
4.1.
Check contents against fig.1. If anything is missing or damaged, contact your local Sealey stockist.
4.2.
Referring to fig.2, place an axle bush (18) onto the axle of the frame tube assembly(1).
4.3.
Attach the pneumatic wheel (5) then a Ø16 flat washer (17) to the mounting tube axle. Secure with split pin (11) and repeat procedure for the
other side. Additional Ø16 flat washers (17) are provided to adjust the spacing between the axle bushing (18) and the pneumatic wheel (5).
4.4.
Rotate one pneumatic wheel (5) so that the hole on the inside of the wheel boss aligns with the corresponding hole in the axle tube. Insert
inner hex bolt M5x45 (10) through the axle tube and secure with lock nut M5 (12) as shown in figure 2.
4.5.
Attach the hitch tube (2) to the frame tube assembly tube (1) using hex bolt M6x40 (9), big flat washer M6 (15) and M6 lock nut (13) as
shown in figure 3. At this stage do not fully tighten the nut and bolt.
4.6.
Attach one brace (3) to either side of the hitch tube (2) using hex bolt M6x35 (8) and M6 lock nut (13) as shown in figure 4. Do not fully
tighten the nut at this stage.
fig.2
fig.3
fig.4
fig.5
4.7. 4.8. 4.9.
4.10.
4.11. 4.12.
4.13. 4.14.
4.15. 4.16. 4.17. 4.18. 4.19. 4.20. 4.21. 4.22. 4.23. 4.24. 4.25. 4.26.
Attach the other ends of the braces (3) to the frame tube assembly (1) using hex bolt M6x35 (8) and M6 lock nuts (13) as shown in figure 5. All nuts and bolts used for the braces (3) can now be fully tightened. Place the hopper (6) over the frame tube assembly (1) so that the shaft protruding from the impeller on the frame tube assembly locates into the swivel bush on the base of the hopper. Align the six bolt holes in the hopper assembly with the six bolt holes on the frame tube assembly and fit the Hex Bolts M6x40 (9) with the big flat washers M6 (15) at the bolt heads. Loosely attach the M6 lock nuts (13) as shown in figure 6. Adjust the hopper assembly over the frame tube assembly until the impeller is free to rotate without any resistance. Fully tighten the nuts and bolts securing the hopper assembly to the frame tube assembly. Attach the R-pin (19) to the shaft protruding above the impeller as shown in figure 7. Attach a Ø8 flat washer (16) over the loose end of the adjustable connection rod and insert the rod through the hole in the fixing plate at the base of the hopper and secure with a M8 lock nut (14) as shown in figure 8. Place the hopper screen (4) into the hopper (6) so that it sits squarely on the base. The spreader is now fully assembled and ready for use.
fig.6
fig.7
fig.8
5. OPERATION
5.1.
Read the Safety Instructions in Section 1 before operating the spreader.
5.2.
Secure the spreader onto the prime mover using the towing pin on the hitch tube (2). Secure the towing pin with the R-pin provided.
The spreader can be converted to use a ball hitch by fitting a Sealey Ø50mm Towing Hitch, Model No. TB36, available from your Sealey
stockist.
5.3.
Load the product into the hopper, ensuring that it is evenly distributed and the maximum capacity of the spreader is not exceeded. When
handling hazardous products it is important to first read the safety data sheet and take necessary safety precautions. A full range of
personal safety equipment is available from your Sealey stockist.
5.4.
The towing speed will affect the rate of flow from the spreader. It is advisable to operate the spreader at lower speeds for a more effective
flow of the product.
5.5.
The adjustable feed system is controlled by movement of the handle on the hitch tube (2). Operate the spreader at the desired speed and
adjust the handle either forwards or backwards until a satisfactory rate of flow is achieved. A locking device is provided on the gauge to
allow the optimum flow required to be maintained.
5.6.
Clean the spreader thoroughly after use, paying particular attention to the area around the adjustable feed system and the impeller.
6. MAINTENANCE.
6.1.
After each use clean material out of hopper.
6.2.
Rinse/dry inside and outside of spreader after each use.
6.3.
Before operating make sure that the tyres are inflated to the correct pressure.
6.4.
Periodically check all fastenings are tight.
6.5.
Annually clean and lightly lubricate parts.
© Jack Sealey Limited
Original Language Version
SPB57T Issue 5 14/04/23
6.6.
To avoid damaging the spreader never exceed the rated load capacity of 57kg.
6.7.
Before storing ensure that the spreader is clean and dry.
6.8.
Store indoors or in a protected area during severe weather and in the winter months.
6.9.
Never allow material to stay in the hopper for extended periods of time.
WEIGHT OF BAG (LBS) 5 10 15 20 25 30 35 40 45 50 55
(CHART ‘A’) SQUARE FOOT COVERAGE PER BAG (LBS/1000 SQ.FT)
5000 SQ.FT COVERAGE
10000 SQ.FT COVERAGE
1.0lb
0.5lb
2.0lb
1.0lb
3.0lb
1.5lb
4.0lb
2.0lb
5.0lb
2.5lb
6.0lb
3.0lb
7.0lb
3.5lb
8.0lb
4.0lb
9.0lb
4.5lb
10.0lb
5.0lb
11.0lb
5.5lb
15000 SQ.FT COVERAGE 0.3lb 0.7lb 1.0lb 1.3lb 1.7lb 2.0lb 2.3lb 2.3lb 3.0lb 3.3lb 3.7lb
MATERIALS TO BE USED
GRIT SEED FERTILISER WEED KILLER E.T.C.
LBS/1000 SQ.FT
1 2 3 4 5 6 7 8 9 10 11
(CHART ‘B’) SPREADER SETTINGS/SPREADER WIDTHS
G/M²
SPREADER SETTING
SMALL PARTICLE SPREAD
5
5
5-6 ft
10
8
5-6 ft
15
10
5-6 ft
20
13
5-6 ft
25
15
5-6 ft
30
18
5-6 ft
35
20
5-6 ft
40
23
5-6 ft
45
25
5-6 ft
50
28
5-6 ft
55
30
5-6 ft
MEDIUM PARTICLE SPREAD
6-9 ft
6-9 ft 6-9 ft 6-9 ft 6-9 ft 6-9 ft 6-9 ft 6-9 ft 6-9 ft 6-9 ft 6-9 ft
LARGE PARTICLE SPREAD
9-12 ft
9-12 ft 9-12 ft 9-12 ft 9-12 ft 9-12 ft 9-12 ft 9-12 ft 9-12 ft 9-12 ft 9-12 ft
.
ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
REGISTER YOUR PURCHASE HERE
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on [email protected] or 01284 757505. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
SPB57T Issue 5 14/04/23
Sealey - Leading Professional Tool & Workshop Equipment Supplier
