Jonathan Y Jyl9916 Chloe 14 Inch Tall Led Wall Sconce Instruction Manual

JYL9916 Chloe 14 Inch Tall LED Wall Sconce

Product Information

Model: JYL9916

Product Dimensions: 4.75”W X 14H X 4.625E

Product Usage Instructions

WARNING: We recommend installation of this
lighting fixture be done by a licensed electrician. Switch off the
main electrical supply from the main fuse box/circuit breaker
before installation. Inspect the item carefully before attempting
to install. If there is any damage or obvious defect, do not
install. The item may not be returned once it has been
installed.

NOTICE & IMPORTANT SAFETY INSTRUCTIONS:

• Please make sure that you have all parts indicated before you
  begin assembly of this item.
• This item should be assembled on a soft surface to prevent
  scratching the finish during assembly.
• To reduce the risk of fire, electrical shock, or injury to
  persons or property, please follow the guidelines below for safe
  use and installation.
• The external flexible cable or cord of this lamp cannot be
  replaced. If the cord is damaged, the lamp shall be destroyed.

Part List and Hardware List

Estimated Assembly Time: 20 minutes.

1. Hit the anchor screw to the ceiling.
2. Fix the Mounting Bracket (C) onto the outlet box and ceiling
   with Machine Screw (D) and Tapping Screw (E).
3. Make the wire connected with Wire Connectors (B), following the
   reference chart listed below.
4. Fix Back Plate (F) onto the Mounting Bracket (C) with Machine
   Screw (G).
5. Connect Hot, Black or Red Outlet Supply Wire to:
   • Black * Parallel Cord (round & smooth)
6. Connect Neutral, White Outlet Supply Wire to:
   • White * Parallel Cord (square & ridged)
   • Clear, Brown, Gold, or Black without Tracer (colored
     stripes)
   • Clear, Brown, Gold, or Black with Tracer (colored stripes)
   • Insulated Wire (not green) with copper metal conductor
   • Insulated Wire (not green) with Silver metal conductor
7. Note: When parallel wire (SPT I & SPT II) is used,
   the neutral wire is square shaped and ridged, and the hot wire will
   be round in shape and smooth. (See Illustration on left.)
8. Grounding Instructions:
   • a) For installation in the United States: Wrap ground wire from
     outlet box around green ground screw on mounting bracket, no less
     than 2 from wire end. Tighten ground screw. If fixture is supplied
     with a ground wire, connect to outlet ground wire with a wire
     connector.
   • b) For installation in Canada: If fixture is supplied with
     ground wire, wrap ground wire around green grounding screw on
     mounting bracket. Tighten ground screw.
9. Install Bulb (H). Be sure to use light Bulb (H) with wattage no
   greater than specified on this fixture. Always make sure that
   electrical current is turned off before changing bulbs.

Please use Type A bulb max 40-watt or CFL bulb max 13-watt or
LED max 9-watt. There are 1 x 4W LED bulbs in the box.

Enjoy your lamp!

WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slighly damperned clean clorth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS * Please make sure that you have all parts indicated before you begin assembly of this item * This item should be assembled on a soft surface to prevent scratching the finish during assembly * To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation *The external flexible cable or cord of this lamp cannot be replaced If the cord is damaged, the lamp shall be destroyed
Part List and Hardware List

Model#: JYL9916 Product Dimensions: 4.75”W X 14″H X 4.625″E

1/2

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes.
1. Hit the anchor screw to the ceiling

2. Fix the Mounting Bracket(C) onto the outlet box and ceiling with machine Screw(D) and Tapping Screw (E).

3. Make the wire connected with Wire Connectors(B), following the reference chart listed below.

4. Fix Back Plate(F) onto the Mounting Bracket(C) with the Machine Screw (G)

Connect, Hot, Black or Red Outlet Supply Wire to:
Black * Parallel Cord (round & smooth)

Connect, Neutral, White Outlet Supply Wire to:
White * Parallel Cord (square & ridged)

Clear, Brown, Gold or Black without Tracer (colored stripes)

Clear, Brown, Gold or Black with Tracer (colored stripes)

Insulated Wire (not green) with copper metal conductor

Insulated Wire (not green) with Silver metal conductor.

*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )

Grounding Instructions: a) For installation in the United States: Wrap ground wire from outlet box around green ground screw on mounting bracket, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector. b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bracket. Tighten ground screw.

5. Install Bulb( H ). Be sure to use light Bulb( H ) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.

PLEASUE USE TYPE”A” BULB MAX 40-WATT OR CFL BULB MAX 13-WATT OR LED MAX 9-WATT THERE ARE 1 X 4W LED BULBS IN THE BOX.
ENJOY YOUR LAMP

2/2