T0686 Matte Black Malmo 16 Inch Tall Wall Sconce
Product Information:
The T0686 fixture is a wall-mounted light with a glass shade
that uses a Type T10 bulb (not included) with a maximum wattage of
60W. The fixture features a photocell function that automatically
turns the light on at dusk and off at dawn. The fixture comes with
a mounting plate unit, mounting screws, wire connectors, bolt nut,
rubber pads, and a hardware package.
Product Usage Instructions:
- Before installing, consult local electrical codes for wiring
and grounding requirements. - Turn off the main power at the circuit breaker before
installing the fixture. - Unscrew the two bolt nuts (D) and remove the two rubber pads
(E) and the mounting plate unit (A) from the backplate. - Attach the mounting plate unit (A) to the outlet box using two
mounting screws (B). Adjust the length of the preinstalled fixture
mounting screws if necessary. Make sure that two fixture mounting
screws are lined up horizontally to make the fixture level. - Attach the backplate of the fixture to the mounting plate unit
(A) by aligning and inserting the two fixture mounting screws into
set holes on the backplate, then secure it with two rubber pads (E)
and two bolt nuts (D). With silicone caulk compound, caulk
completely around where the backplate meets with the wall surface
to prevent water from seeping into the outlet box. - Install the bulb (not included). See relamping label at socket
area or packaging for maximum wattage allowed. - Attach the glass shade to the fixture by aligning studs and
slots, then rotate it carefully until it is locked in place. - To disconnect the dusk-to-dawn photocell, turn off the power at
the fuse or circuit box. Loosen the wire connector connected with
the wires from the photocell. Do not remove the photocell to
prevent water from seeping into the outlet box. - Take a white pigtail and black pigtail and make wire
connections using wire connector (C):- The black wire from the fixture to one end of the black
pigtail. - The white wire from the fixture to one end of the white
pigtail. - The other end of the black pigtail to the black wire from the
power source. - The other end of the white pigtail to the white wire from the
power source. - Put all wires back into the backplate of the fixture.
- The black wire from the fixture to one end of the black
- Turn on the power at the fuse or circuit box.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
T0686
WWARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Plate Unit (A)
Mounting Screw (B)
Wire Connector (C) Photocell
Bolt Nut (D)
Rubber Pad (E)
Fixture
Rubber Pad (E) Bolt Nut (D)
Outlet Box House Ground Wire Fixture Mounting Screw Green Ground Screw Mounting Plate Unit (A) Mounting Screw (B) Fixture Ground Wire Wire Connector (C)
Fixture Wire Backplate
Max.60W Type T10 Bulb (not included)
IMPORTANT: The sensor has an excellent photocell function to enable the light to turn on at dusk and off at dawn automatically.
Glass Shade
Installation Steps
Turn off the power at fuse or circuit box.
1. Unscrew the two bolt nuts (D)
remove the two rubber pads (E) and the mounting plate unit (A) from the backplate.
2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled fixture mounting screws if necessary. Note: Make sure that two fixture mounting screws are lined up horizontally to make the fixture level.
Page 1 / 3
221025
T
3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows: · Connect the hot wire (black insulation) from the fixture to the black wire from the power source. · Connect the neutral wire (white insulation) from the fixture to the white wire from the power source. · Attach the fixture ground wire (bare wire) to the mounting plate unit (A) with green ground screw. Then, depending on local code, connect it to the house ground wire with the wire connector (C). Carefully put all of the wires back into the outlet box.
4. Attach the backplate of the fixture to the mounting plate unit (A) by aligning and inserting the two fixture mounting screws into set holes on backplate, then secure it with two rubber pads (E) and two bolt nuts (D). Note: With silicone caulk compound, caulk completely around where the backplate meets with the wall surface to prevent water from seeping into the outlet box.
5. Install the bulb (not included). See relamping label at socket area or packaging for maximum wattage allowed.
6. Attach the glass shade to the fixture by aligning studs and slots, then rotate it carefully until it is locked in place.
Turn on the power at fuse or circuit box.
Optional Installation: Disconnect Dusk-to-Dawn Photocell
IMPORTANT: Compatible with dimmer when photocell is disconnected. * Requires dimmable bulb and compatible dimmer switch.
Photocell Black Wires From Photocell White Wires From Photocell Red Wires From Photocell
Wire Connector
Wires From Fixture
Wires From Main Power
Pigtail
Wires From Fixture
White Pigtail
Fig.1
Wire Connector (C)
Fig.2
1. Turn off the power at the fuse or circuit box before starting installation.
2. Loosen the wire connector connected with the wires from photocell. (See Fig.1) Note: Do not remove the photocell to prevent water from seeping into the outlet box.
3. Take a white pigtail and black pigtail and make wire connections using wire connector (C): (See Fig.2) a. The black wire from the fixture to one end of the black pigtail. b. The white wire from the fixture to one end of the white pigtail. c. The other end of the black pigtail to the black wire from the power source. d. The other end of the white pigtail to the white wire from the power source. Put all wires back into the backplate of the fixture.
Turn on the power at fuse or circuit box.
Page 2 / 3
221025
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Assembly Kit 6590MM (1 SET)
Mounting Plate Unit (A) Mounting Screw (B) Wire Connector (C) Bolt Nut (D) Rubber Pad (E)
Glass Shade 10333CS
A B
A: 15-3/4″ B: 6-1/2″ C: 5-1/4″
C
Page 3 / 3
221025
