Vaxcel T0653 Chiasso 2 Light 14 Tall Outdoor Wall Sconce Instruction Manual

T0653 Chiasso 2 Light 14 Tall Outdoor Wall Sconce

Product Information

The product is a light fixture with a photocell backplate that
turns on the light at dusk and off at dawn automatically. It comes
with a hardware package that includes a mounting plate unit,
mounting screws, wire connector, bolt nut, rubber pad, and a cover.
The product is compatible with a maximum 60W Type A bulb (not
included) and can be used with a dimmer switch if the photocell is
disconnected.

Product Usage Instructions

1. Before installation, turn off the power at the circuit breaker
   or fuse box.
2. Consult local electrical codes for wiring and grounding
   requirements.
3. Read and save the instructions.
4. Assembly and installation:
   1. Unscrew the two bolt nuts (D), remove the two rubber pads (E),
      and the mounting plate unit (A) from the backplate.
   2. Attach the mounting plate unit (A) to the outlet box using two
      mounting screws (B). Adjust the length of the preinstalled fixture
      mounting screws if necessary. Make sure that the fixture mounting
      screws are lined up horizontally to make the fixture level.
   3. Attach the backplate of the fixture to the mounting plate unit
      (A) by inserting fixture mounting screws into set holes on the
      backplate, then secure it with two rubber pads (E) and two bolt
      nuts (D). Use silicone caulking compound to caulk completely around
      where the backplate meets with the wall surface to prevent water
      from seeping into the outlet box.
   4. Remove the cover from the fixture.
   5. Install bulbs (not included). See relamping label at socket
      area or packaging for maximum wattage allowed.
   6. Attach the cover back to the top of the fixture carefully.
5. Turn on the power at the fuse or circuit box.
6. Optional installation: Disconnect Dusk-to-Dawn Photocell
   1. Turn off the power at the fuse or circuit box.
   2. Loosen the wire connectors connected with the wires from
      photocell. Do not remove the photocell to prevent water from
      seeping into the outlet box.
   3. Take a white pigtail and black pigtail and make wire
      connections using wire connectors (C):
      1. The black wire from the fixture to one end of the black
         pigtail.
      2. The white wire from the fixture to one end of the white
         pigtail.
      3. The other end of the black pigtail to the black wire from the
         power source.
      4. The other end of the white pigtail to the white wire from the
         power source. Put all wires back into the back plate of the
         fixture.

Re-Order Parts

The following parts are available for re-order if damaged or
missing:

• Mounting Plate Unit (A)
• Mounting Screw (B)
• Wire Connector (C)
• Bolt Nut (D)
• Rubber Pad (E)

ASSEMBLY AND INSTALLATION INSTRUCTIONS
T0653
WWARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):

Mounting Plate Unit (A)

Mounting Screw (B)

Wire Connector (C)

Bolt Nut (D)

Rubber Pad (E)

Max. 60W Type A Bulb (not included)

Cover

IMPORTANT: The sensor has an excellent photocell function to enable the light to turn on at dusk and off at dawn automatically.

Photocell Backplate

Outlet Box House Ground Wire Fixture Mounting Screw Green Ground Screw Mounting Plate Unit (A) Mounting Screw (B) Fixture Ground Wire
Wire Connector (C) Fixture Wire
Rubber Pad (E) Bolt Nut (D)
T

Page 1 / 3

Max. 60W Type A Bulb (not included)
220527

Installation Steps
Turn off the power at fuse or circuit box.
1. Unscrew the two bolt nuts (D), remove the two rubber pads (E) and the mounting plate unit (A) from the backplate.
2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled fixture mounting screws if necessary. Note: Make sure that the fixture mounting screws are lined up horizontally to make the fixture level.
3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows: · Connect the hot wire (usually black insulation) from the fixture to the black wire from the power source. · Connect the neutral wire (usually white insulation) from the fixture to the white wire from the power source. · Attach the fixture ground wire (usually green insulation or bare wire) to the mounting plate unit (A) with the green ground screw. Then, depending on local code, connect it to the house ground wire with the wire connector (C). Carefully put all of the wires back into the outlet box.
4. Attach the backplate of the fixture to the mounting plate unit (A) by inserting fixture mounting screws into set holes on the backplate, then secure it with two rubber pads (E) and two bolt nuts (D). Note: With silicone caulking compound, caulk completely around where the backplate meets with the wall surface to prevent water from seeping into the outlet box.
5. Remove the cover from the fixture.
6. Install the bulbs (not included). See relamping label at socket area or packaging for maximum wattage allowed.
7. Attach the cover back to the top of the fixture carefully.
Turn on the power at fuse or circuit box.

Optional Installation: Disconnect Dusk-to-Dawn Photocell
IMPORTANT: Compatible with dimmer when photocell is disconnected. * Requires dimmable bulb and compatible dimmer switch.

Photocell Black Wires From Photocell White Wires From Photocell Red Wires From Photocell
Wire Connector

Wires From Fixture
Wires From Main Power

Pigtail

Wires From Fixture

White Pigtail
Fig.1

Wire Connector (C)
Fig.2

Page 2 / 3

220527

1. Turn off the power at the fuse or circuit box before starting installation.
2. Loosen the wire connectors connected with the wires from photocell. (See Fig.1) Note: Do not remove the photocell to prevent water from seeping into the outlet box.
3. Take a white pigtail and black pigtail and make wire connections using wire connectors (C): (See Fig.2) a. The black wire from the fixture to one end of the black pigtail. b. The white wire from the fixture to one end of the white pigtail. c. The other end of the black pigtail to the black wire from the power source. d. The other end of the white pigtail to the white wire from the power source. Put all wires back into the back plate of the fixture.
The following parts are available for re-order if damaged or missing.
Spare Parts List:

Mounting Plate Unit (A)

Mounting Screw (B)

Cover 10307CG

Wire Connector (C)
Assembly Kit 6531MM (1 SET)

Bolt Nut (D)

Rubber Pad (E)

A B

A: 14-1/4″ B: 5″ C: 7-1/2″
C

Page 3 / 3

220527