RS26 Rider Auto Scrubber
Rider Auto Scrubber
www.icecompanies.com
Operator & Parts Manual
RS26 RS28-OB RS32
8300004 REV.06 (11-2022)
INTELLIGENT CLEANING EQUIPMENT
OPERATOR MANUAL
READ OPERATOR MANUAL CAREFULLY!
IMPORTANT: To ensure full warranty protection, please fill out & return your warranty card.
Please fill out at time of installation for future reference. Model No. Serial No. Machine Options Sales Rep. Sales Rep. Phone No. Customer ID Number Installation Date
HOW TO ORDER PARTS Only use ICE Company supplied or equivalent parts. Parts and supplies may be ordered online,by phone, by fax or by mail. 1. Identify the machine model. 2. Identify the machine serial number from the data label. 3. Ensure the proper serial number is used from the parts list. 4. Identify the part number and quantity.
Do not order by page or reference numbers. 5. Provide your name, company name, customer ID number,billing and shipping address,
phone number and purchase order number.
PROTECT THE ENVIRONMENT Please dispose of packaging materials,old machine components such as batteries, hazardous fluids, including antifreeze and oil, in an environmentally safe way according to local waste disposal regulations.
Always remember to recycle.
ICE Company Limited XiangShi Road LiaoBu DongGuan GuangDong China Tel: 0769 – 81869000 Fax:0769 – 81863000
Specifications and parts are subject to change without notice.
2
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
TABLE OF CONTENTS
SAFETY PRECAUTIONS…………………………………………………………………………………………4 MACHINE COMPONENTS……………………………………………………………………………………5-6 MACHINE SETUP & INSTALLATION…………………………………………………………………………7 MACHINE OPERATION…………………………………………………………………………………………..8 WHILE OPERATING MACHINE………………………………………………………………………………..9 TANK DRAINING…………………………………………………………………………………………………..10 BATTERY CHARGING…………………………………………………………………………………………..10 PREVENTATIVE MAINTENANCE……………………………………………………………………………11 FAULT CODE AND ELIMINATE………………………………………………………………………………12 TECHNICAL SPECIFICATION………………………………………………………………………………..13 PARTS LIST……………………………………………………………………………………………………14-45 WEAR AND TEAR PARTS…………………………………………………………………………………..46 WIRING DIAGRAM……………………………………………………………………………………………….47
ICE RS26 / RS28-OB / RS32
3
OPERATOR MANUAL
SAFETY PRECAUTIONS
This machine is intended for commercial use. It is designed exclusively to scrub hard floors in an indoor environment and is not constructed for any other use. Only use recommended accessories.
All operators shall read, understand and exercise the following safety precautions:
1. Do not operate machine: – Unless trained and authorized. – Unless you have read and understand the operators manual. – In flammable or explosive areas. – With brake disabled. – If not in proper operating condition.
2. Before starting machine: – Make sure all safety devices are in place and operate properly. – Check brakes and steering for proper operation.
3. When using machine: – Go slow on inclines and slippery surfaces. – Follow all safety guidelines. – Be very careful when using the machine in reverse. – Reduce speed when turning. – Report and fix any damage to machine prior to operating it. – Never allow children to play on or around.
4. Before leaving or servicing machine: – Stop on level surface. – Turn off machine.
5. When servicing machine: – Read operators manual thoroughly prior to operating or servicing this machine. – Use manufacturer supplied or approved replacement parts. – Secure machine with wheel blocks prior to jacking the machine up. – Use approved jack or hoist to safely elevate the machine. – Disconnect batteries prior to working on machine. – Wear gloves when handling batteries or battery cables.
– Avoid any contact with battery acid – Avoid moving parts. Do not wear loose fitting
clothing while servicing machine.
WARNING: Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep battery compartment open when charging.
WARNING: Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks.
WARNING: Flammable materials or reactive metals can cause explosion or fire. Do not pick up.
4
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
MACHINE COMPONENTS
1. Solution tank 2. Hose fill port & Cap 3. Squeegee assembly 4. Wheels, 10 inch 5. Scrub head assembly 6. Side squeegee assembly 7. Watching window, on-
board battery charger 8. Brake pedal 9. Propel pedal 10. Front drive wheel
11. Operator seat 12. Steering wheel 13. LED light, work 14. Adjusting handle, seat 15. Off-board battery
charger receptacle 16. Detergent level watching
window 17. Warning light 18. Recovery tank cover 19. Recovery tank 20. Cup holder 21. Cap 22. Detergent bottle 23. Battery box
ICE RS26 / RS28-OB / RS32
5
OPERATOR MANUAL MACHINE COMPONENTS
24. Directional switch 25. Main power key switch 26. Emergency stop switch 27. Warning light switch 28. Vacuum motor switch & indicator 29. Detergent dosage adjusting
buttons & indicator 30. Batteries meter 31. LED display screen 32. Fault indicator 33. Fault code 34. Fault message 35. Hour meter 36. Solution flow adjusting buttons &
indicator 37. Horn button 38. 1-Step switch & Indicator 39. Brush pressure adjusting button
& indicator 40. Drain hose, recovery tank 41. Drain hose, solution tank 42. Vacuum hose
6
ICE RS26 / RS28-OB / RS32
MACHINE SET UP & INSTALLATION
UNCRATING MACHINE
Be sure and check packing carton for any damage. Immediately report any damage to carrier. Check the contents of package to ensure that the following items are included:
· Machine · 4-6V Batteries · Squeegee assembly · 2-Pad drivers
OPERATOR MANUAL
3. Carefully place the batteries into the compartment as shown in figure below. Place the battery brace at the rear of the batteries. NOTE: Do not drop the batteries into the compartment!
4. Connect battery cables to posts in numbered order as shown in drawing below. NOTE: RED to POSITIVE and BLACK to NEGATIVE.
1. Uncrate the wooden box, place the top board on the edge of pallet, lie in the front of the machine, as below shown.
5. Reinstall the Operator seat and the Battery box.
WARNING: Do not operate machine unless you have read & understood this manual. 2. Install batteries.(see INSTALLING BATTERIES) 3. Turn on the Main power key switch (machine
components, #25), make sure the Squeegee assembly (machine components, #3) and the Scrub head assembly (machine components, #5) is off the floor. 4. Sit in the Operator seat (machine components, #11), hold the Steering wheel (machine components, #12), press the Propel pedal (machine components, #9) and driving slowly the machine down from the slope.
MACHINE SET UP
INSTALLING BRUSHES OR PADS 1. Turn off the 1-Step switch (machine
components, #38) and raise the Scrub head assembly off the floor, then stop machine on the level surface, remove the key and ensure the machine is turned off. 2. If using the pad driver, first attach the appropriate pad to the pad driver surface. 3. Align the pad driver or brush under the motor hub and push it upward to engage.
INSTALLING BATTERIES
WARNING: Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas.Keep sparks and open flames away! Keep battery compartment open when charging.
Recommended battery spec: 4-6V, 260AH@20HR deep cycle batteries.
Max. batteries dimensions : 300mm (L) X 180mm (W) X 290mm (H) 1. Turn the Main power key switch off. 2. Remove the Operator seat & the Battery box
(machine components, #23).
4. To remove the pad driver or brush, raise the scrub head and remove the Side squeegee assembly (machine components, #6), push the edge of brush downward.
ICE RS26 / RS28-OB / RS32
7
OPERATOR MANUAL
5. For Orbital head model RS28-OB, you need to attach a rectangular 28in (710mm) ×14in (356mm) pad to the Orbital Pad driver, align the pad to the orbital pad driver, press from to back and side to side to alignment.
MOUNTING THE SQUEEGEE ASSEMBLY 1. Turn off the 1-Step switch and raise the
Squeegee assembly off the floor. 2. Mount the squeegee assembly to the squeegee
pivot bracket. make sure the knobs are completely seated into the slots before securing knobs. 3. Connect the Vacuum hose (machine components, #42) to the squeegee assembly. Loop the hose by using the hose clip provided. 4. Check the squeegee blades for proper adjustment.
FILLING THE SOLUTION TANK The machine is equipped with a Hose fill-port (machine components, #2) at the side of the machine, and a bucket fill-port located under the recovery tank. NOTE: Before accessing the bucket fill-port make sure that the recovery tank is empty. When filling the solution tank with a bucket, make sure that the bucket is clean. Do not use the same bucket for filling and draining the machine.
WARNING: Do not put any flammable materials into solution tank. this can cause an explosion or a fire.
FILLING THE DETERGENT BOTTLE The machine is equipped with a 6 liters Detergent bottle (machine components, #22). Open the Cap (machine components, #21) you can fill detergent, and watch the liquid level on the Detergent level watching window (machine components, #16).
The ratio of water and detergent is 0~5%, you can adjust this ratio via pressing the Detergent dosage adjusting buttons (machine components, #29).
NOTE: Only use recommended cleaning chemicals. Contact your janitorial supply distributor for recommendations on proper chemicals.
8
MACHINE OPERATION
WARNING: Do not operate machine unless you have read and understand this manual.
PRE-OPERATION CHECKS
1. Check the tank cover seals for damage. 2. Drain the recovery tank, check the vacuum fan
inlet filter, clean them if necessary. 3. Check the vacuum hose for debris or blockage. 4. Check the squeegees for damage, wear and for
deflection adjustment. 5. Check whether Pad/Bruch is installed properly . 6. Check the brakes and steering for proper
operation.
OPERATION THE MACHINE 1. Sit in the Operator seat, adjusting the seat
to comfortable place by pushing the Seat adjustment handle (machine components, #14). NOTE: The machine will not travel unless the operator is sitting in the operator seat. 2. Turn on the machine. Check the LED display screen (machine components, #31) , if there are fault codes (machine components, #33) and the Fault indicator (machine components, #32) is blink, please Do Not operation the machine unless the faults have been eliminated (please see FAULT CODES AND ELIMINATE section). 3. Select the preferred settings by pressing the Brush pressure adjusting buttons (machine components, #39) , Solution flow adjusting buttons (machine components, #36) and Detergent dosage adjusting buttons. NOTE: Use the minimal pressure and flow as possible. 4. Turn on the 1-Step switch, the Scrub head assembly and the Squeegee assembly will lower down automatically, all the presetting functions will turn on. 5. The machine can scrub in both forward and backward, place the Directional switch (machine components, #24) in the forward direction is to move forward, backward is to move backward. The horn will sound and the squeegee will raise automatically (the vacuum motor will turn off after a short delay) when drive machine backwards. This is to prevents damaging the squeegee. NOTE: Go slow when drive machine backwards.
ICE RS26 / RS28-OB / RS32
6. Press the Propel pedal, the machine start scrubbing, the speed can be adjusted by controlling the force of foot stepping, light is slow, heavy is fast. NOTE: Go slow on inclines and slippery surfaces.
7. To stop scrubbing, turn off the 1-Step switch, the scrub head will raise automatically, the squeegee will also raise after a short delay (the vacuum indicator flashing), please keep moving until the dirty water is picked up, and then release the propel pedal and stop scrubbing.
8. Turn off the machine.
BRAKE DEVICE The machine is drived by the Front drive wheel (machine components, #10), that is equipped with a brake device. When you release the Propel pedal, the machine will stop travel, the park brake will engage after a short delay. The machine is equipped with a Brake pedal (machine components, #8), that can be used to control the machine if quicker stopping is needed or if operating on an incline.
EMERGENCY STOP BUTTON The machine is equipped with an Emergency stop button (machine components, #26), please push it if an emergency, that will shut off all power of machine and brake immediately. To restart the machine, please reset the Emergency stop button, and turn off the Main power key switch, then turn on key switch. NOTE: Please hold the steering wheel when emergency stop.
WHILE OPERATING MACHINE
WARNING: Fire Or Explosion Hazard. Do Not Pick Up Flammable Materials Or Reactive Metals. 1. Go slow on inclines and slippery surfaces, go
slow when turn and reverse. Do not operate the machine on inclines that exceed 7% (4°). 2. Drive machine in a straight path as possible, avoid turning the Steering wheel too sharply when machine is in motion. avoid sudden turns except emergencies. 3. Do not keep the machine in the same position with pad / brush spinning, keep the machine moving to prevent damage to floor finish. 4. If the squeegee assembly leaves streaks on the floor, raise the squeegee off the floor and wipe
OPERATOR MANUAL
the blades down with a damp cloth. Pre-sweep the area to prevent leaving streaks on the floor. 5. To obtain the optimum cleaning performance, you can adjust the brush pressure, solution flow and detergent dosage as your required. If poor picking up water performance is observed, please stop scrubbing and check the squeegee blade, adjust or replace if necessary. 6. If the dirty water path exceed the width of squeegee, please adjust the side squeegee assembly. 7. Pour a recommended defoamer into the recovery tank if excessive foam appears.
WARNING: The foam do not activate water level switch, excessive foam may result in vacuum motor damage. 8. Press the Horn button (machine components,
#37) to alert if necessary. 9. The machine is equipped with a Warning light
(machine components, #17), you can select turn ON or OFF by the Warning light switch (machine components, #27). 10. If there is a fault code F10 (Batt low) on the LED display screen, the machine will stop scrubbing and alarm, please drive the machine to charging. 11. If there is a fault code F08 (Rec Tank Full) on the LED display screen, the vacuum motor will stop working and alarm, please drive the machine to drain water. If there is a fault code F09 (Soln Tank Empty) on the LED display screen, the Detergent system will stop working and alarm, please fill the solution tank. 12. If there are other fault codes on the LED display screen, please turn off the machine, eliminate the fault (please see FAULT CODES AND ELIMINATE section), then restart machine. 13. For heavily soiled areas, please use DOUBLE SCRUBBING mode. The first time: Turn on the 1-Step switch, then press the Vacuum motor switch (machine components, #28), its indicator will turn off and the squeegee will raise automatically, then start to scrubbing this areas without picking up water. The second time: turn on the Vacuum motor switch, the squeegee will lower down automatically, and then start to scrubbing and picking up water. 14. If you only want to pick up water needn’t scrubbing, Turn on the Vacuum motor switch (squeegee will lower down) and turn off the 1-Step switch (if it is ON), the scrub head will raise and then start to working.
ICE RS26 / RS28-OB / RS32
9
OPERATOR MANUAL
TANK DRAINING
DRAINING THE RECOVERY TANK Any time scrubbing is completed, or when refilling solution tank, the recovery tank should be drained and cleaned.
WARNING: If the recovery tank is not drained when the solution tank has been refilled, foam or water may enter the float shutoff screen and cause damage to the vacuum motor. 1. While holding the Recovery tank drain hose
(machine components, #40) upward, remove the cap and lower hose to drain. 2. Open the Recovery tank cover (machine components, #18) and rinse out the tank. Use a rag to remove any excess dirt. Clean the vacuum fan inlet filter located in the recovery tank .
DRAINING THE SOLUTION TANK Any time scrubbing operation is completed, the solution tank should be drained and cleaned. 1. While holding the Solution tank drain hose
(machine components, #41) upward, remove the cap and lower hose to drain. 2. Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lines.
BATTERY CHARGING
WARNING: Fire Or Explosion Hazard. Batteries Emit Hydrogen Gas. Keep Sparks and Open Flame Away. Keep Battery Compartment Propped Open When Charging.
Use only apprved chargers with the following specifications:
· Automatic shut off circuit · Deep cycle charging · Output current of 20-30 Amps · Output voltage of 24 volts
ON-BOARD BATTERY CHARGER As standard configuration, the machine is equiped with the On-board battery charger. The settings of On-board battery charger had been set for the recommended batteries type.
WARNING: The On-board battery charger setting’s change are to be completed by authorized service centers only. Failure to properly set will result in the batteries or charger damage.
1. Transport the machine to a well ventilated area. 2. Turn the machine off. 3. If charging wet (lead acid) batteries check the
fluid level before charging. 4. Prop up the Operator seat by the support stand
for ventilation. 5. Connect the charger’s AC power supply cord to
a properly grounded receptable. 6. The charger will automatically begin to charge,
you can watching the charging status on the window (machine components, #7), once the charging cycle begins, the indicator lights will progress from red, yellow to green. when the green indicator light comes on, the charging cycle is done. Unplug the charger cord. NOTE: The machine will can not operate when charging.
PREVENTATIVE MAINTENANCE
WARNING: Before performing any maintenance on the machine, be sure that the power is turned off, or the batteries are disconnected!
WARING: Repairs are to be completed by Authorized service centers only. Any repairs completed by unauthorized persons will avoid the warrenty.
DAILY MAINTENANCE 1. Remove pad driver/ brush and clean with
approved cleaner. 2. Drain recovery and solution tanks completely
and rinse out with clean water. Visually check the recovery tank for debris and clean out as necessary. 3. Raise the squeegee assembly off floor and wipe it down with a damp towel. Be sure to store the squeegee in the up position.
10
ICE RS26 / RS28-OB / RS32
4. Remove the vacuum fan inlet filter and rinse it out with clean water.
5. Clean machine with an approved cleaner and a damp towel.
6. Recharge the batteries. 7. Check the condition of the squeegee blade
wiping edge, rotate blade if worn.
MONTHLY MAINTENANCE 1. Clean the battery tops to prevent corrosion. 2. Check for loose battery cable connections. 3. Inspect and clean the recovery tank cover seal.
Replace it if damaged. 4. Lubricate all grease points and pivot points with
silicon spray and approved grease. 5. Check the machine for loose nuts and bolts. 6. Check the machine for leaks.
MOTOR MAINTENANCE 1. Contact your local Distributor for any motor
maintenance. 2. Motor should have the brushes checked every
250 hours. Brushes should be replaced when they are worn to a length of 10 mm or less.
BATTERY MAINTENANCE
WARNING: Batteries emit hydrogen gas and an explosion o fire can result. Keep sparks and fire away from batteries at all times.
WARNING: Whenever servicing batteries, be sure to wear protective gloves. Avoid contact with battery acid at all times.
OPERATOR MANUAL
NOTE: For the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition.
1. Always follow the battery charging directions as outlined in the BATTERY CHARGING section of this manual.
2. Keep battery tops and terminals free from corrosion. A strong solution of baking soda and water is the best way to keep the batteries corrosion free. DO NOT ALLOW THE BAKING SODA / WATER SOLUTION TO ENTER THE BATTERY CELLS.
3. Use a wire brush with the baking soda solution to properly clean the battery posts and connections.
4. Check battery connections for wear and loose terminals. replace if necessary.
MACHINE STORAGE 1. Always store the machine indoors. 2. Always store the machine in a dry area. 3. Always store the machine in its upright position. 4. Always store the machine with the pad driver/
brush raised off the floor. 5. Always store the machine with the squeegee
assembly raised off the floor. 6. If storing in an area which may reach freezing
temperatures, be sure to drain all fluids from the machine prior to storage. Any damage caused by freezing temperatures will not be covered by the warranty. 7. Drain the recovery tank. 8. Drain the solution tank of all fluid.
FAULT CODE & SOLUTION
The machine is equipped with a LED display screen (see Machine components, item # 31), the LED screen will display the operating hours (see Machine components, item # 35) and the battery level status (see Machine components, item # 30).
Once fault occuring, please DO NOT continue operate the machine unless the fault are eliminated. Turn off the machine, then to solve the fault, the fault code & message will be eliminated when machine restart.
When the machine detects a fault, there will be a Fault code (see Machine components, item #33) & Fault message (see Machine components, item #34) display on the LED screen, and the Fault indicator (see Machine components, item #32) will flash continuously, accompany an audible alarm Occasionally.
If the fault is occurred frequently, or the fault can’t be eliminated, please contact ICE service center.
Please refer to the below table to determine the fault cause and the solution.
ICE RS26 / RS28-OB / RS32
11
OPERATOR MANUAL
FAULT CODE & SOLUTION
FAULT CODE
F01 F02
F03
F04
F05
F06
F07 F08 F09 F10
F11
FAULT MESSAGE
Seat Empty
Squeegee Actt O.L. RE-START! Bru Actt O.L. RESTART! Vac Mtr O.L. RE-START!
Left Bru Mtr O.L. RE-START!
Right Bru Mtr O.L. RE-START!
Propel Mtr O.L. RE-START!
RecTank Full
Soln Tank empty
Batt Low Charge Batt Batt Empty Charge Batt NOW
FAULT CAUSE
SOLUTION
Not sit in the seat
Sit in the operator seat
Squeegee lifting actuator is overload
Scrub head lifting actuator is overload
Vacuum motor overload Left brush motor is overload
Turn off the machine,after a moment, RE-START machine.
Right brush motor is overload
Propel motor overload Recovery tank is full Solution tank is empty Battery is low
Drain the Recovery tank Fill the solution tank Charge the battery
Battery is empty
Charge the battery NOW
F12
Brake Wiring Error
Bad Brake wiring
Check the brake wiring
F13
Release Foot pedal
Stepping the propel pedal when starting machine
F14
Replace Brake Assy Bad Brake assembly
F16
Control Unit Overheat! Wait
Control Unit Overheat
F17
Replace Control Unit Control Unit Fault
F18 Replace Accel Pedal Sensor Bad Accelerator pedal sensor
F19 Replace Brake pedal sensor Bad Accelerator pedal sensor
F20 Check Left Brush motor Bad left brush motor
F21
Check Vac Mtr
Bad Vacuum motor or wiring
F22
Check Soln Solenoid Solution solenoid wiring fault
F23
Replace Soln solenoid Bad Solution solenoid
F24
Check Propel Motor Bad propel motor
F25 Check Right Brush motor Bad right brush motor
F40
Check Proximity Sw Proximity switch fault
F42
Replace Control Unit Bad Control Unit
F43
Turn Dead Sw Off RE-START!
Emergency stop button activated
F44
Replace Control Unit
F45
Return Control Unit
F46
Return Control Unit
Bad Control Unit
F47
Return Control Unit
F48
Return Control Unit
Release the propel pedal
Replace the brake assembly Turn off the machine,after a moment, RE-START machine Replace the control unit Replace accelerator pedal sensor Replace accelerator pedal sensor Check left brush motor/ wiring Check the vacuum motor / Wiring Check the wiring & Contactors Replace the solution solenoid Check the propel motor / Wiring Check right brush motor/ wiring Check the Proximity switch Replace the control unit Release emergency stop button and restart machine
Contact service center, Replace the Control Unit
12
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
TECHNICAL SPECIFICATIONS
MODEL
RS26 DUAL DISK
RS32 DUAL DISK
RS28-OB ORBITAL
LENGTH
61.6 in / 1,565 mm
WIDTH (MACHINE WITH SCRUB HEAD)
32 in / 815 mm 37.4 in / 950 mm 31.5 in / 800 mm
HEIGHT
56.7 in / 1,440 mm
WEIGHT
618 lbs / 280 Kg
640 lbs / 290 Kg
WEIGHT WITH BATTERIES
880 lbs / 400 Kg
900 lbs / 410 Kg
RECOVERY TANK CAPACITY
29 Gal / 110 L
SOLUTION TANK CAPACITY
29 Gal / 110 L
SQUEEGEE WIDTH
CLEANING PATH WIDTH
PRODUCTIVITY RATE PER HOUR (IN THEORY) TRAVEL SPEED (TRANSPORT)
33.8 in / 860 mm
26 in / 650 mm ( 2 x 13 inch)
46, 300 ft2 4,300 m2
40 in / 1,030 mm
32 in / 810 mm ( 2 x 16 inch)
55, 600 ft2 5,200 m2
28 in / 710 mm (28in x 14in Pad)
49, 500 ft2 4,600 m2
4 Mile / h 6.5 Km / h
MINIMUM AISLE TURN PAD/BRUSH PRESSURE SOLUTION FLOW BATTERIES
71 in / 1,800 mm
75 in / 1,900 mm
80 lbs / 35 Kg 120 lbs / 55 Kg 165 lbs / 75 Kg
0 ~ 0.7 Gal / Min 0 ~ 2.7 L / Min
132 lbs / 60 Kg 165 lbs / 75 Kg 200 lbs / 90 Kg
4 x 6V, 240AH@20Hr
VOLTAGE
24V DC
DRIVE WHEEL BRUSH MOTOR VIBRATIONS @ SEAT VACUUM MOTOR
1.1 hp / 0.8 KW (2) 0.6 hp / 0.45KW, 210 RPM
N/A 0.6 hp / 0.45KW
0.75 hp / 0.55KW, 2200 RPM
< 2.5 m / s2 < 8.2 ft / s2
VACUUM WATER LIFT (MAX)
70 in. H2O / 1780 mm. H2O
RUN TIME PER CHARGE
3~3.5 Hours
3.5~4.0 Hours
DECIBEL RATING AT OPERATOR’S EAR, INDOORS
68 dB(A)
GRADE LEVEL, MAX
Scrubbing: 4°/7% Transporting (empty):10°/17.5%
ICE RS26 / RS28-OB / RS32
13
OPERATOR MANUAL
MAIN FRAME GROUP
14
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
DIA PART NO. NUMBER
1
8310102
2
8310133
8310930A 3
8310931
4
1421409
5
1422411
6
1221412
8310119 7
1612605
8
1436025
9
8310150
10
6210131
11
1421510
12
1221512
13
8310120
14
1421824
15
1422821
16
1021825
17
8210118
18 8310708A
19
1421307
20
1211316
MAIN FRAME GROUP
DESCRIPTION
MAIN FRAME, WELDED RUBBER GROMMET PERISTALTIC PUMP, KIT TUBING, PUMP FLAT WASHER, M4×9×0.8 LOCK WASHER M4 SCREW, PAN HEAD, M4×12 10″ WHEEL, PU TIRE BALL BEARING,6205-2RS RETAINING RING, 25MM WHEEL CAP NYLON, CLAMP FLAT WASHER, M5×10×1.0 SCREW, PAN HEAD, M5×12 BRACKET, STAND FLAT WASHER, M8×24×2.0 LOCK WASHER M8 BOLT, HEX, M8×25 STATIC STRAP HORN, 24VDC, KIT PLAT WASHER, M3×7×0.5 SCREW, PAN HEAD, M3×16
NO REQ’D
1 5 1 1 2 2 2 2 4 2 2 5 5 5 2 3 3 3 1 1 4 2
ICE RS26 / RS28-OB / RS32
15
OPERATOR MANUAL STEERING & DRIVE WHEEL GROUP
16
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
DIA PART NO. NUMBER
1
1113014
2
1421428
8310602 3
8310699A
4
8310608
5
1021825
6
1422821
7
1421816
8
8310609
9
8310605
10
1654025
11
8310604
12
1534508
13
1123507
14
1421510
15
6210131
16
8310645
17
1021060
18
1422026
19
1421030
20
8310601
21
1021820
22
1421824
23
8310640
24
8310431
25
8310603
26
8310660
27
8310611
28
8310612
29
8310613
30 8310625A
STEERING & DRIVE WHEEL GROUP
DESCRIPTION
LOCK NUT, M14 FLAT WASHER, M14×28×2.0 STEERING WHEEL CUSHION WITH ICE LOGO BELLOWS, SHAFT, STEERING BOLT, HEX HEAD, M8×25 LOCK WASHER, M8 FLAT WASHER, M18×16×1.6 BEARING, FLANGE SHAFT, STEERING WHEEL KEY, 4.75×4.75×25.4 U-JOINT SET SCREW, M5 ×8 LOCK NUT, M5 FLAT WASHER, M5×10×1.0 CLAMP, NYLON BRACKET, FLANGE BEARING BOLT, HEX HEAD, M10×60 LOCK WASHER, M10 FLAT WASHER, M10×30×2.5 SUPPORT BRACKET, STEERING BOLT, HEX HEAD, M8×20 FLAT WASHER, M14×24×2.0 ACCELERATOR/ BRAKE PEDAL HALL SENSOR WITH CABLE STEER-CONTROL ASSY. DRIVE WHEEL, 24VDC 800W PU TIRE, DRIVER WHEEL ARMATURE BRUSH BRUSHES CONNECTION BOX ELECTRICALLY RELEASED BRAKE
NO REQ’D
1 1 1 1 1 8 6 4 2 1 2 1 4 3 3 3 1 4 4 4 1 4 8 1 1 1 1 1 4 2 1
ICE RS26 / RS28-OB / RS32
17
OPERATOR MANUAL SOLUTION TANK GROUP
18
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
DIA PART NO. NUMBER
1
8310101
2
1221512
3
1421510
4
8113009
5
1021820
6
1421824
7
8310139
8
8310151A
9
8310132
10
1222508
11
1512820
12
1421816
13
8310140
14
1422821
15
8310130
16
8310124
17
8310142
18
8310141
19 8310238A
20
8310125
21
1021825
22
8310225
23
8310224
24
1962050
25
8011030
26
8310123
27
8310122
SOLUTION TANK GROUP
DESCRIPTION SOLUTION TANK SCREW, PAN HEAD, M5×12 FLAT WASHER, M5×10×1.0 CLAMP, NYLON BOLT, HEX HEAD, M8×20 FLAT WASHER, M8×24×2.0 PLATE NON-SLIP MAT FOOTREST PLATE SCREW, M5×8 SCREW, HEX SOCKET, M8×20 FLAT WASHER, M8×16×1.6 JUNCTION PLATE LOCK WASHER, M8 BRACKET, SOLUTION TANK MNTG ELBOW, G1/2 NUT, M36 SEALING SENSOR, SOLUTION LEVEL, KIT CAP, SOLUTION TANK BOLT, HEX HEAD, M8×25 SLEEVE, 8.1×12.7×7.8 ARM, RECOVERY TANK SUPPORT CLAMP, 2 INCH HOSE ASSEMBLY ADAPTER, STRAINER ASSY STRAINER ASSY
NO REQ’D
1 2 2 2 12 13 2 2 1 4 2 2 2 8 3 1 1 2 1 1 1 1 1 1 1 1 1
ICE RS26 / RS28-OB / RS32
19
OPERATOR MANUAL RECOVERY TANK GROUP
20
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
DIA PART NO. NUMBER
1
8310238A
2
8310201
3
8310237
4
1021820
5
1421824
6
8310227
7
1513820
8
8310226
9
8310250
10
8012008
11
1421618
12
1321413
13
1221516
14
1421510
15
2310129
16
6210111
17
8011030
18
1962050
19
4010316
20
8310126
21
8113009
22
1221512
23
8310221
24
8310220
25
8310222
26
8310216
27
8310219
28
1022860
29
1123810
30
1021825
31
8310225
32
8310223
33
8310215
34
8310211
35
8310214
RECOVERY TANK GROUP
DESCRIPTION
SENSOR, SOLUTION LEVEL, KIT RECOVERY TANK FILTER, DUST BOLT, HEX HEAD, M8×20 FLAT WASHER, M8×24×2.0 HINGE, WELDED SCREW, HEX SOCKET, M8×20 HINGE, LEAF DEBRIS COLLECTOR BUSHING FLAT WASHER, M6×18×1.6 SELF-TAPPING, ST4.8 x 13 SCREW, PAN HEAD, M5×16 FLAT WASHER, M5×10×1.0 CLAMP, HOSE CLAMP, HOSE DRAIN HOSE CLAMP, 2 INCH ICE LOGO HINGE ASSY. CLAMP, NYLON SCREW, PAN HEAD, M5×12 SPACER COMPRESSION SPRING FLAT WASHER, LARGE COVER, SOLUTION TANK SEALING STRIP BOLT, HEX HEAD, M8×60 LOCK NUT, M8 BOLT, HEX HEAD, M8×25 SLEEVE, 8.1×12.7×7.8 ARM, RECOVERY TANK SUPPORT BRACKET, RECOVERY TANK SUPPORT BRACKET, SUPPORT SPACER, RUBBER
ICE RS26 / RS28-OB / RS32
NO REQ’D
1 1 1 21 25 2 2 2 1 2 2 2 8 12 2 2 1 1 2 2 4 4 2 2 4 1 1 2 1 1 2 1 1 1 1
21
OPERATOR MANUAL RECOVERY TANK COVER GROUP
22
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
DIA PART NO. NUMBER
1
1221512
2
1421510
3
8310165A
4
1123507
5
8310241
6
8310202
8310260 7
8132006
8
8310207
9
1962050
10
1123608
11
1421612
12
8310204
13
8310205
14
8310230
15
1021620
16
8310232
17
1421618
18
1022600
19
8310228
20
8310231
21
1021616
22
8310236
23
8310235
24
8310229
25
1021610
26
1422616
27
1021820
28
1421824
29
8310203
30
8310208
31
8310209
32
8310234
33
1311316
34
8310206
RECOVERY TANK COVER GROUP
DESCRIPTION
SCREW, PAN HEAD, M5×12 FLAT WASHER, M5×10×1.0 CAUTION LIGHT, KIT LOCK NUT, M5 PLATE, CATUION LIGHT RECOVERY TANK COVER AMETK VACUUM MOTOR, 3 STAGE, KIT CARBON BRUSH FOR VACUUM MOTOR VACUUM HOSE CLAMP, 2 INCH LOCK NUT, M6 FLAT WASHER, M6×12×1.6 ADAPTER, VACUUM HOSE GASKET, ADAPTER GASKET, DUST FILTER BOLT, HEX HEAD, M6×20 BRACKET FLAT WASHER, M6×18×1.6 BOLT, HEX HEAD, M6×100 SUPPORT, RECOVERY TANK COVER SLEEVE, 6.4×9.5×4 BOLT, HEX HEAD, M6×16 SPACER, NYLON SLEEVE, 6.4×9.5×8 SEALING STRIP BOLT, HEX HEAD, M6×10 LOCK WASHER, M6 BOLT, HEX HEAD, M8×20 FLAT WASHER, M8×24×2.0 PLATE, VACCUM MOTOR MNTG ISOLATER, M6 BRACKET, VACCUM MOTOR INSULATION SCREW, SELF-TAPPING, ST4.8×16 SEAL, FAN
NO REQ’D
5 9 1 2 1 1 1 2 1 2 8 4 1 1 1 4 1 12 1 1 1 1 1 1 1 2 3 4 4 1 3 1 1 4 1
ICE RS26 / RS28-OB / RS32
23
OPERATOR MANUAL CONTROL PANEL GROUP
24
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
DIA PART NO. NUMBER
1
1221512
2
1421510
3
8311703
4
8311702
5
8310712
8310773 6
8310775
7
1221306
8
8310701
9
1421824
10
1422821
11
1021825
12
1321110
13
1421409
14
8133610
15
8133601
16
1221520
17
8133602
18
4010316
19
8310711
20
8310702
8310704
21
8312704
8310750
22
2010121
23
8310709
24
8310707
25 8310706A
CONTROL PANEL GROUP
DESCRIPTION SCREW, PAN HEAD, M5×12 FLAT WASHER, M5×10×1.0 DECAL, CONTROL PANEL PLATE, CONTROL PANEL GASKET, CONTROL PANEL PCB, CONTROL PANEL (AGM / EN) PCB, CONTROL PANEL (WET FLOODED / EN) SCREW, PAN HEAD, M3×6 CONROL HOUSING FLAT WASHER, M8×24×2.0 LOCK WASHER, M8 BOLT, HEX HEAD, M8×25 SCREW, SELF-TAPPING, ST3.5×10 FLAT WASHER, M4×9×0.8 LED LIGHT, KIT BASE, LED LIGHT SCREW, PAN HEAD, M5×20 COVER, LED LIGHT ICE LOGO GASKET, SWITCH PANEL PLATE, SWITCH PANEL DECAL, SWITCH PANEL, RS32 DECAL, SWITCH PANEL, RS28-OB DECAL, SWITCH PANEL, RS26 ICE LOGO, SMALL ROCKER SWITCH EMERGENCY STOP SWITCH KEY SWITCH, KIT
NO REQ’D
8 11 1 1 1 1 1 5 1 4 4 4 3 3 1 1 3 1 1 1 1 1 1 1 1 2 1 1
ICE RS26 / RS28-OB / RS32
25
OPERATOR MANUAL MAIN CONTROLLER GROUP
26
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
DIA PART NO. NUMBER
1
1021616
2
1422616
3
1421618
4
8310480
5
8114705
6
8310422
7
8310133
8
8310740
9
8014068
10
8310450
11
1211330
12
8310425
13
1021825
14
1422821
15
1421828
16
1123305
17
1434300
18
8310423
19
1421307
20
1211320
21
8310763
22
8112030
23
1123507
24 8210106A
25
1121505
26
8310452
27
1421510
28
1221520
8310790 29
8310790-OR
30
1423612
31
1023612
32
1422513
33
1221525
CONTROLLER GROUP
DESCRIPTION
SCREW, HEX HEAD, M6×16 LOCK WASHER, M6 FLAT WASHER, M6×18×1.6 FUSE, 150A INSULATOR BRACKET, INSULATOR RUBBER GROMMET CIRCUIT BREAKER, 5A CIRCUIT BREAKER, 10A BRACKET, SCRUB HEAD LIFTING SCREW, PAN HEAD, M3×30 BRACKET BOLT, HEX HEAD, M8×25 LOCK WASHER, M8 FLAT WASHER, M8×28×2.5 LOCK NUT, M3 WASHER, TOOTH, M3 MICRO SWITCH FLAT WASHER, M3×7×0.5 SCREW, PAN HEAD, M3×20 OFF BOARD CHARGER SOCKET POWER CORD, BATTERY CHARGER, US LOCK NUT, M5 ON BOARD BATTERY CHARGER, 25A HEX NUT, M5 BRACKET, BATTERY CHARGER FLAT WASHER, M5×10×1.0 SCREW, HEX HEAD, M5×20 MAIN CONTROLLER, RS26 / RS32 MAIN CONTROLLER, RS28-OB FLAT WASHER M6× 12×1, COPPER HEX BOLT M6 X 12, COPPER LOCK WASHER,M5 SCREW, HEX HEAD, M5×25
ICE RS26 / RS28-OB / RS32
NO REQ’D
12 18 15 1 3 2 2 1 1 1 2 2 5 5 5 4 4 1 2 2 1 1 4 1 4 1 6 4 1 1 10 10 2 2
27
OPERATOR MANUAL SEAT & DETERGENT SYSTEM GROUP
28
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
SEAT & DETERGENT SYSTEM GROUP
DIA PART NO. NUMBER
1
1221412
DESCRIPTION SCREW, HEX HEAD, M4×12
2
8133502 CLAMP
3
8133501 CARGO NET
4
1123810
LOCK NUT, M8
5
8310413 SUPPORT, SEAT
6
8117007
NYLON SPACER
7
8310415 TORSION SPRING
8
8310414
SLEEVE, 8.2×11×15
9
1421816
FLAT WASHER, M8×16×1.6
10
1021830
BOLT, HEX HEAD, M8×30
11
8310411
PLATE, SEAT MNTG
12
8310133
RUBBER GROMMET
13
1512820
SCREW, HEX SOCKET, M8×20
14 8310402K SEAT, KIT
15
1021616
SCREW, HEX HEAD, M6×16
16
1421618
FLAT WASHER, M6× 18×1.6
17
8310418
CUP HOLDER
18
8310419
BRACKET, CUP HOLDER
19
1123608
LOCK NUT, M6
20
8310460
SPACER
21
8310463
ADAPTOR, KEY
22
8310464
INSERT, LOCK
23
8310461
BOTTLE, DETERGENT
24
8310462
CAP, BOTTLE
25
1021820
BOLT, HEX HEAD, M8×20
26
1422821
LOCK WASHER, M8
27
1421828
FLAT WASHER, M8×28×2.5
28
8310465
BOX, DETERGENT BOTTLE
29
8310421
BRACKET
NO REQ’D
4 4 1 5 1 1 1 1 2 1 1 1 4 1 4 4 1 1 2 1 1 1 1 1 2 2 5 1 1
ICE RS26 / RS28-OB / RS32
29
OPERATOR MANUAL
BATTERY GROUP
30
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
DIA PART NO. NUMBER
1
8310401
2
1021820
3
1422821
4
1421824
5
8310131
6
8210105
7
8310135
8
8310407
9
8310136
10
8310736
11
8310737
12
8310733
13
8114751
14
8210141
15
1221412
16
8310406
17
8210114
18
1662316
19
8310404
20
1421409
21
8310403
BATTERY GROUP
DESCRIPTION BOX, BATTERY BOLT, HEX HEAD, M8×20 LOCK WASHER, M8 FLAT WASHER, M8×24×2.0 SUPPORT, BATTERY, REAR BATTERY, 6V 230AH TRAY, BATTERY PLATE SUPPORT, BATTERY, FRONT BATTERY CONNECT CABLE, RED BATTERY CONNECT CABLE, RED BATTERY CONNECT CABLE, BLACK JACKET, BATTERY TERMINAL,BLACK BATTERY CONNECT CABLE, BLACK SCREW, PAN HEAD, M4×12 COVER COVER RIVET, 3.2×16 HINGE ASSEMBLY FLAT WASHER, M4×9×0.8 COVER
NO REQ’D
1 8 4 8 1 4 1 2 1 1 1 1 8 3 4 1 1 4 1 4 1
ICE RS26 / RS28-OB / RS32
31
OPERATOR MANUAL SCRUB HEAD LIFTING GROUP
32
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
DIA PART NO. NUMBER
1
8310320
2
8210301
3
8310311
4
8310312
5
8210309
6
8310303A
7
8310305
8
8310314
9
8310313
10
1032090
11
1421030
12
8310304
13
1421020
14
8310307
15
1123012
16
8310144
17
8310118
18
1011025
19
8310306
20
8310308
SCRUB HEAD LIFTING GROUP
DESCRIPTION
PIN, COTTER PIN, 9.5×38 PIN, 16×150 PIN, 16×57 PIN, COTTER LINEAR ACTUATOR, KIT PLATE, ARM, SCRUB HEAD LIFTING FLAT WASHER, LARGE PIN, 12×90 BOLT, HEX HEAD, M10×90 FLAT WASHER, M10×30×2.5 BRACKET, SCRUB HEAD LIFTING FLAT WASHER, M10×20×2 BUSHING, FLANGE LOCK NUT, M10 SLEEVE, 16×18.6×25.4 ARM, SCRUB HEAD LIFTING BOLT, HEX HEAD, M10×25 SLEEVE, 10.5×18.5×34 SPRING
NO REQ’D
1 1 1 4 6 1 2 2 1 1 4 1 2 2 3 4 2 4 2 1
ICE RS26 / RS28-OB / RS32
33
OPERATOR MANUAL ORBITAL HEAD LIFTING GROUP RS28-OB
34
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
ORBITAL HEAD LIFTING GROUPRS28-OB
DIA PART NO. NUMBER
DESCRIPTION
1
8340517 SHOULDER BOLT, M8
2
1123808
LOCK NUT, M8
3
8310303A LINEAR ACTUATOR, KIT
4
8340133 DAMPER,RUBBER
5
1032200 BOLT, HEX HEAD, M12×100
6
1421132
FLAT WASHER, 13×32×1.5
7
8340134 DAMPER,RUBBER
8
8340136 SHOULDER, M10
9
1021825 BOLT, HEX HEAD, M8×25
10
8340131
BRACKET, GUIDE
11
1421824
FLAT WASHER, M8×24×2.0
12
8117007
NYLON WASHER, 12.9×24×2.5
13 8125415 JOURNAL BEARING
14
8125414
SLEEVEE, STAINLESS STEEL
15
8133151
DAMPER, RUBBER
16
1435013
WAVE WASHER, 13×24×0.5
17
8340120
BRACKET, ORBTIAL HEAD LIFT
18
1123115
NUT,LOCK, M12
19
8340132
DAMPER
20
8340137
BRACKET, ACTUATOR
21
1421030
FLAT WASHER, M10×30×2.5
22
1123012
LOCK NUT, M10
23
8340135
SHOULDER BOLT, M10
NO REQ’D
1 8 1 2 2 7 4 1 4 1 2 4 4 2 3 2 1 2 6 1 3 3 2
ICE RS26 / RS28-OB / RS32
35
OPERATOR MANUAL
SCRUB HEAD GROUP
36
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
DIA PART NO. NUMBER
8310399 1
8310316
2
1655025
8311301 3
8310301
4
1021830
5
1421824
6
8310356
7
8210532
8
1123810
9
8210531
10
8310355
8310365 11
8310366
12
8310357
13
1421020
14
1422010
15
1023010
16
8210804
17
8210805
18
1421828
19
1422821
20
9000004
9050013 21
9050016
22
9000003
9040013 23
9040016
8311358 24
8310358
8311359 25
8310359
26
1421618
27
1021616
28
8310361
29
1021840
30
8310362
31
8115404
32
1022800
33
8310354
34
8310351
35
8310353
SCRUB HEAD GROUP
DESCRIPTION
BRUSH MOTOR, 24VDC 450W, KIT CARBON BRUSH KEY, 5×5×25 SCRUB HEAD HOUSING, RS26 SCRUB HEAD HOUSING, RS32 BOLT, HEX HEAD, M8×30 FLAT WASHER, M8×24×2.0 BRACKET, LEFT KNOB, M10 LOCK NUT, M8 KNOB, M6 CLAMP, SIDE SKIRT BLADE, SIDE SKIRT, LINATEX BLADE, SIDE SKIRT, PU (OPTION) BRACKET, SIDE SKIRT, LEFT FLAT WASHER, M10×20×2.0 LOCK NUT, 3/8 BOLT, HEX HEAD, 3/8-16×1 SPACER HUB, BRUSH DRIVE FLAT WASHER, M8×28×3.0 LOCK WASHER, M8 CLUTCH, G-400S BRUSH, 13 INCH, RS26 BRUSH, 16 INCH, RS32 CENTER LOCK, #3 PAD DRIVER, 13 INCH, RS26 PAD DRIVER, 16 INCH, RS32 SKIRT, RS26 SKIRT, RS32 CLAMP, SKIRT, RS26 CLAMP, SKIRT, RS32 FLAT WASHER, M6×18×1.6 BOLT, HEX HEAD, M6×16 BRACKET, PROTECTIVE WHEEL BOLT, HEX HEAD, M8×40 PROTECTIVE WHEEL SLEEVE, 8×12.7×12.7 BOLT, HEX HEAD, M8×100 KNOB, M10 BRACKET, SIDE SKIRT, RIGHT BRACKET, RIGHT
NO REQ’D
2 4 2 1 1 9 18 1 4 9 10 2 4 4 1 6 6 6 4 2 2 2 2 2 2 2 2 2 1 1 1 1 7 7 1 1 1 6 1 4 1 1
ICE RS26 / RS28-OB / RS32
37
OPERATOR MANUAL ORBITAL HEAD GROUPRS28-OB
38
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
DIA PART
NO. NUMBER
1
8340109
2
8146110
3
1123012
4
1421030
5
8146520
6
8146116
7
1962016
8
8146350
9
8146511
10
1022830
11
1421824
12
8115404
13
1435013
14
8116009
15
8310354
16
8340170
17
8340516
18
1123808
19
1021080
20
1535610
21
8146107
22
1421023
23
1513020
24
8340502
25
1513616
26
8146205
27
1513625
28
8146303
29
1123507
30
8340506
31
8146305
32
8146301
33
1521616
34
8146203
35
1612608
36
8146204
37
8146201
38
8146202
39
1513616
40
8340101
41
1421510
42
1221515
43
8340180
44
8310365
45
8340515
46
1514616
ORBITAL HEAD GROUPRS28-OB
DESCRIPTION
MOTOR, 24VDC 560W 2200RPM KEY, 8×7×28 LOCK NUT, M10 FLAT WASHER M10×30×2.5 MOUNTING BRACKET ISOLATORS, M10×25 CLAMP TUBING,ID=12mmWIRE REINFORCED RIGHT-ANGLE TUBING FITTING BOLT, HEX HEAD, M8×30 FLAT WASHER, M8×24×2.0 LBEARING, JOURNAL WAVE WASHER, 13×24×0.5 PROTECTIVE WHEEL KNOB, M10 BRACKET,SKIRT,LEFT KNOB, M10 LOCK NUT, M8 BOLT, HEX HEAD, M10×80 SET SCREW,M6×10 ISOLATORS, M10×25 FLAT WASHER M10×34×3.0 HEX SOCKET SCREW,M10×20 PAD DRIVER HEX SOCKET SCREW,M6×16 PLATE HEX SOCKET SCREW,M6×25 END CAP 3/8 LOCK NUT M5 PVC TUBING PLASTIC CLAMP TEE FITTING 3/8 HEX SOCKET BOLT,M6×16 BEARING HOUSING BALL BEAING 6008 BEARING HOUSING ECCENTRIC SHAFT ECCENTRIC HEX SOCKET SCREW,M6×20 MOTOR MOUNTING BRACKET FLAT WASHER, M5×10×1.0 SCREW M5×15 BRACKET,SKIRT,RIGHT SKIRT BLADE, LINATEX CLAMP STRIP SOCKET ROUND HEAD,M6×16
ICE RS26 / RS28-OB / RS32
NO REQ’D
1 1 20 20 2 6 2 1 1 3 6 3 3 3 4 1 4 4 4 1 4 4 4 1 4 1 4 2 6 2 6 1 2 1 1 1 1 1 4 1 6 6 1 2 2 10
39
OPERATOR MANUAL SQUEEGEE GROUP /
40
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
SQUEEGEE GROUP /
DIA PART
NO. NUMBER
1
8310506
PIN, 10×45
DESCRIPTION
2
8310590A LINEAR, ACTUATOR, KIT
3
8310320 PIN, COTTER
4
1121008
HEX NUT, M10
5
8310503 BRACKET, SQUEEGEE
6
8310240 VACUUM HOSE
7
1123115
LOCK NUT, M12
8
8310550 CASTER, 2 INCH
9
8310501 COMPRESSION SPRING,
10
8310504
ARM, SQGE LIFTING
11
8310505
FLEX BUSHING, TPU
12
8210525
SHORT CLAMP ASSEMBLY
13
1221575
SCREW, PAN HEAD, M5×75
14
8118624
SHAFT
15
8118623
SPACER
16
1123507
LOCK NUT, M5
17
8311514 8310514
CLAMP ASSEMBLY, RS26 CLAMP ASSEMBLY, RS28-OB / RS32
8311531
REAR BLADE, LINATEX, RS26
8310531 REAR BLADE, LINATEX, RS28-OB / RS32
18
8311541
REAR BLADE, PU, RS26, OPTION
8310541 REAR BLADE, PU, RS28-OB / RS32, OPTION
19
8311561 8310561
SQUEEGEE HOSING, RS26 SQUEEGEE HOSING, RS28-OB / RS32
20
8311562 8310562
RETAINER, SQUEEGEE, RS26 RETAINER, SQUEEGEE, RS28-OB / RS32
21
8311560
SQUEEGEE ASSEMBLY, RS26
8310560 SQUEEGEE ASSEMBLY, RS28-OB / RS32
8311534
FRONT BLADE, LINATEX, RS26
22
8310534
FRONT BLADE, LINATEX, RS28-OB / RS32
8311544
FRONT BLADE, PU, RS26, OPTION
8310544 FRONT BLADE, PU, RS28-OB / RS32, OPTION
23
1021835
BOLT, HEX HEAD, M8×35
24
8210518
KNOB, M8
25
8115404
SLEEVE, 8× 12.7×12.7
26
8116009
PROTECTIVE WHEEL
27
1421824
FLAT WASHER, M8× 24×2
28
1123810
LOCK NUT, M8
29
8210309
PIN, COTTER
30
8310311
PIN, 16×150
31
8310508
PIN, 12×100
32
8310509
EXTENSION SPRING
33
1031212
BOLT, HEX HEAD, M12×120
34
1421030
FLAT WASHER, M10× 30×2.5
35
1021060
BOLT, HEX HEAD, M10×60
36
8310507
ADAPTER
ICE RS26 / RS28-OB / RS32
NO REQ’D
2 1 2 2 1 1 1 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 4 2 2 4 2 2 1 1 2 1 1 1 1
41
OPERATOR MANUAL SOLUTION & DETERGENT SYSTEM
42
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
DIA PART NO. NUMBER
1
8310124
2
1962025
3
8310901
4
8310375
5
8310371
6
1421510
7
1422513
8
1221512
9
8310902
10
8310903
11
8310374
12
8310904
13
8310905
14 8310930A
15
1914080
16
8310910
17
8310467
18
8310909
19
8310466
SOLUTION & DETERGENT SYSTEM
DESCRIPTION ELBOW, G1/2 CLAMP 16-25MM TUBING, ID=16MM L=500MM ELBOW, CHEMICAL CONNECTOR SOLENOID VALVE, 24VDC FLAT WASHER, M5×10×1.0 LOCK WASHER M5 SCREW, PAN HEAD, M5×12 TUBING, ID=16MM L=40MM TUBING, ID=12MM L=175MM FITTING, PLASTIC TUBING, ID=12MM L=210MM TUBING, ID=4MM L=330MM DETERGENT PUMP, KIT TIE, 3×80MM TUBING, ID=4MM L=100MM FITTING TUBING, ID=4MM L=30MM ONE WAY VALVE
NO REQ’D
1 8 1 1 1 2 2 2 1 1 1 1 3 1 19 3 7 4 1
ICE RS26 / RS28-OB / RS32
43
OPERATOR MANUAL SOLUTION & DETERGENT SYSTEM RS28-OB
44
ICE RS26 / RS28-OB / RS32
OPERATOR MANUAL
SOLUTION & DETERGENT SYSTEM (RS28-OB)
DIA PART NO. NUMBER
DESCRIPTION
1
8119007
ELBOW, G1/2
2
1962025 CLAMP 16-25MM
3
8310904 TUBING, ID=12MM L=210MM
4
1021616 HEX BOLD M6 X 16
5
1422616 LOCK WASHER, M6
6
1421612
FLAT WASHER, M6×12×1.0
7
8340507 BRACKET, SOLENOID VALVE
8
1221412 SCREW, PAN HEAD, M4×12
9
1422411
LOCK WASHER, M4
10
1421409
FLAT WASHER, M4×9×0.8
11
8119003
SOLENOID VALVE, 24VDC
12
8119201
TUBING, ID=12MM L=70MM
13
8600139
FITTING, PLASTIC
14
8146350
TUBING,ID=12mmWIRE REINFORCED
15
8146511
RIGHT-ANGLE TUBING FITTING
16
8310905
TUBING, ID=4MM L=330MM
17 8310930A DETERGENT PUMP, KIT
18
1914080
TIE, 3×80MM
19
8310910
TUBING, ID=4MM L=100MM
20
8310467
FITTING
21
8310909
TUBING, ID=4MM L=30MM
22
8310466
ONE WAY VALVE
NO REQ’D
1 6 1 2 2 2 1 2 2 2 1 1 1 1 1 3 1 19 3 7 4 1
ICE RS26 / RS28-OB / RS32
45
OPERATOR MANUAL
DIA PART NO. NUMBER
1
8310119
2
8116009
3
8310362
8311531 4
8310531
8311534 5
8310534
9050013 6
9050016
9040013 7
9040016
8146116 8
8146107
WEAR AND TEAR PARTS
DESCRIPTION
10″ WHEEL, PU TIRE PROTECTIVE WHEEL PROTECTIVE WHEEL REAR BLADE, LINATEX, RS26 REAR BLADE, LINATEX, RS28-OB / RS32 FRONT BLADE, LINATEX, RS26 FRONT BLADE, LINATEX, RS28-OB / RS32 BRUSH, 13 INCH, RS26 BRUSH, 16 INCH, RS32 PAD DRIVER, 13 INCH, RS26 PAD DRIVER, 16 INCH, RS32 ISOLATORS, M10 x 25 , RS28-OB ISOLATORS, M10 x 25 , RS28-OB
NO REQ’D
2 2 1 1 1 1 1 2 2 2 2 6 4
46
ICE RS26 / RS28-OB / RS32
47
ICE RS26 / RS28-OB / RS32
BAT: 4-6VDC batteries FU: 150A fuse CW: Off-board charger interlock switch BR1: Main controller circuit breaker, 5A KEY SW: Main power key switch AS: Alarm lamp switch LED2: Alarm lamp CH1: On-board battery charger CH2: Off-board battery charger port
LED1: Work LED light BR2: Brake circuit breaker, 10A M3: Traction motor M1: Brush motor, left / Orbital head motor M6: Brush motor, right M2: Vacuum motor AP: Accelerator Pedal, sensor SL: Solution tank water level sensor RF: Recovery tank water level sensor
RT: Reverse switch ST: Seat switch EG: Emergency stop switch M4: Scrub head lifting actuator M5: Squeegee lifting actuator BK: Brake coil DP: Detergent pump EW: Solution solenoid valve HN: Horn
OPERATOR MANUAL
icecompanies.com
