iW90 Wet-Dry Vacuum Cleaner

Product Information

The iW90 is a Wet/Dry Vacuum Cleaner manufactured by ICE
Cobotics. It is designed for commercial use in indoor environments.
The vacuum cleaner is equipped with a handle assembly and is
capable of both wet and dry operations. The machine features a
float shut-off system to prevent overflow during wet vacuuming. It
is important to read the operator manual thoroughly before
operating or servicing the machine.

Specifications

1. Model: iW90
2. Manufacturer: ICE Cobotics (GuangDong) Company Limited
3. Website: www.icecobotics.com
4. Contact Information:
   • Phone: 0769-8186 9000
   • Fax: 0769-8186 3000
   • Address: XiangShi Road LiaoBu DongGuan GuangDong China

Parts Ordering

To order parts for the iW90 vacuum cleaner, follow these
steps:

1. Identify the machine model.
2. Locate the machine serial number from the data label.
3. Ensure the proper serial number is used from the parts
   list.
4. Identify the part number and quantity.
5. Provide your name, company name, customer ID number, billing
   and shipping address, phone number, and purchase order number.
6. Order the parts online, by phone, by fax, or by mail.

Environmental Protection

ICE Cobotics encourages responsible disposal of packaging
materials, old machine components, and hazardous fluids. Please
dispose of these items in an environmentally safe way according to
local waste disposal regulations. Remember to recycle whenever
possible.

Safety Precautions

The iW90 vacuum cleaner is designed for use on a nominal
120-volt circuit. It should be connected to an outlet with the same
configuration as the grounding plug on the machine. Do not use any
adapters with this machine. The vacuum cleaner is intended for
commercial use in indoor environments only. Use only recommended
accessories. To avoid electrical shock, replace the power cord
immediately if any damage is detected. The replacement should be
performed by an authorized person or the customer service
center.

Product Usage Instructions

Handle Assembly

Prior to operating the iW90 vacuum cleaner, ensure that the
handle is properly assembled on the machine body using the
following instructions:

1. Refer to the handle assembly instructions provided in the user
   manual.
2. Follow the steps outlined in the manual to correctly assemble
   the handle on the machine body.

Operation of Wet & Dry Vacuum

Before operating or servicing the iW90 vacuum cleaner,
thoroughly read the operator manual. Follow the below steps to
perform wet vacuuming:

1. Remove the clear window and take out the cloth or paper filter
   from the vacuum.
2. While the clear window is removed, check that the float
   shut-off is unobstructed and fully functional.
3. Place the clear window back on top of the recovery tank.
4. Connect the vacuum hose to the inlet on the machine body.
5. Attach the appropriate accessory tool for the job.
6. Ensure that the Main Power Switch is in the OFF position, then
   plug the power cord into a grounded outlet.
7. If foam develops in the recovery tank during wet vacuuming, use
   defoamer chemical to help eliminate the foam. Foam can cause vacuum
   motor damage and will not activate the float shut-off.
8. To raise the squeegee assembly back to transport position,
   depress the right half of the pedal (rear of the machine) downward
   with your foot.

Wet / Dry Vacuum Cleaner

www.icecobotics.com

Operator & Parts Manual

iW90

2320601U REV.06(05-2023)

OPERATOR
READ OPERATOR MANUAL MANUAL CAREFULLY
IMPORTANT:To ensure full warranty protection,Please fill out & return your warranty card.
Please fill out at time of installation for future reference. Model No. Serial No. Machine Options Sales Rep. Sales Rep. phone no. Customer ID Number Installation Date
HOW TO ORDER PARTS Only use ICE Cobotics Company supplied or equivalent parts. Parts and supplies may be ordered online,by phone, by fax or by mail. 1. Identify the machine model. 2. Identify the machine serial number from the data label. 3. Ensure the proper serial number is used from the parts list. 4. Identify the part number and quantity.
Do not order by page or reference numbers. 5. Provide your name, company name, customer ID number,billing and shipping address,
phone number and purchase order number.
PROTECT THE ENVIRONMENT Please dispose of packaging materials,old machine components such as batteries, hazardous fluids, including antifreeze and oil, in an environmentally safe way according to local waste disposal regulations.
Always remember to recycle.

ICE Cobotics (GuangDong) Company Limited XiangShi Road LiaoBu DongGuan GuangDong China Tel:0769-8186 9000 Fax:0769-8186 3000
Specifications and parts are subject to change without notice. 1

iW90

TABLE OF CONTENTS

OPERATOR

SAFETY PRECAUTION. . . . . . . . . . . . . . . . . . . . . 3 HANDLE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . 4 MACHINE OPERATON & STORAGE. . . . . . . . . . .5-6 MACHINE COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-15 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 WEAR&TEAR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

iW90

2

OPERATOR
SAFETY PRECAUTION
Carefully read and understand this manual before operating this machine. This machine must be grounded! This machine shall be grounded while in use to protect theoperator from electric shock. Grounding provides a path of least resistance for electric current. This machine is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not remove the ground pin under any circumstances.
This machine is for use on a nominal 120-volt circuit and has a grounding plug that resembles the plug illustrated in Figure. Make sure that the machine is connected to an outlet having the same configuration as the plug. No adapter should be used with this machine.

This machine is intended for commercial use. It is constructed for use in an indoor environment

and is nor intended for any other use. Use only recommended accessories.

1. Do not operate machine:

­ Unless trained and authorized.

­ Unless you have read and

­ In flammable or explosive areas.

understand the operators manual.

­ With a damaged cord or plug

­ With the use of extension cords.

­ If not in proper operating condition.

­ In outdoor areas and standing water.

2. Before operating machine: ­ Make sure all safety devices are in place and operating properly.

3. When using machine: ­ Do not run machine over cord. ­ Do not pull cord around
sharp edges or corners. ­ Do not handle plug with wet hands. ­ Report machine damage or faulty
operation immediately.
4. Before leaving or servicing machine: ­ Turn off machine.

­ Do not pull machine by cord or plug. ­ Do not unplug by pulling on the cord. ­ Do not stretch cord. ­ Keep cord away from heated surfaces.
­ Unplug cord from outlet.

5. When servicing machine: ­ Unplug cord from outlet.

­ Use manufacturer supplied or approved replacement parts.

To avoid electrical shock,please replace the power cord immediately if any damage is being detected. The replacement must be performed only by an authorized person or by our customer service center.

3

iW90

Handle Assembly Instructions

OPERATOR

iW90

4

OPERATOR
Operation of Wet & Dry Vacuum
Read operators manual thoroughly prior to operating or servicing this machine. Be sure that the handle is properly assembled on machine body prior to operating.
Wet Operation
1) Remove clear window and remove the cloth or paper filter form vacuum. 2) While clear window is removed, check to make sure that the float shut-off is unobstructed and fully functional. 3) Replace clear window on the top of the recovery tank. 4) Connect vacuum hose to inlet on the machine body. 5) Attach appropriate accessory tool for the job to be completed. 6) Make sure the Main Power Switch is in the OFF position, then plug power cord into a grounded outlet.
Do not use an extension cord in conjunction with the standard power cord. 7) If using the front-mounted squeegee assembly, be sure that squeegee is attached to front of machine. 8) If using the front-mounted squeegee assembly, lower squeegee to the floor by depressing the left half of the pedal [rear of the machine] forward with your foot. 9) Turn power switch to “on” position. 10) During wet pickup, the float shut-off will automatically prevent water from entering the recovery tank once the recovery tank is full.
If foam develops in the recovery tank during wet vacuuming, use defoamer chemical to help eliminate the foam. Foam will not activate the float shut-off, and therefore, may cause vacuum motor damage. 11) To raise the squeegee assembly back to transport position, depress the right half of the pedal (rear of the machine) downward with your foot.
Dry Operation
1) If the machine has been used for wet pick-up, empty the Recovery Tank, rinse it out and dry it completely and install the Dry Container System. DO NOT use the machine for dry pick-up without the Dry Container System in place. 2) Remove clear window, and be sure the cloth or paper filter is properly installed.

5

iW90

OPERATOR

Do not operate machine without bag or filter properly installed. 3) Replace clear window on the top of the recovery tank. 4) Connect vacuum hose to inlet on the machine body. 5) Attach appropriate accessory tool for the job to be completed. 6) Make sure the Main Power Switch is in the OFF position, then plug power cord into a grounded outlet.

Do not use an extension cord in conjunction with the standard power cord. 7) Turn power switch to “on” position. 8) Check the filter bag periodically to see if it is full. For optimal performance, replace bag when it is 3/4 full.

DRAINING THE RECOVERY TANK
1) Unplug machine from power outlet. 2) Transport machine to nearest floor drain of bucket. 3) Remove drain hose form rear of machine. Remove ball plug from drain hose, and drain the contents of the tank. 4) After the contents have drained, remove the clear window and rinse recovery tank with clean water. 5) Replace the ball plug on the drain hose and hang hose back on the rear of the machine.

To prevent odors in the recovery tank, remover the vacuum head when machine is not in operation to allow air to circulate.
MAINTENANCE
To keep the machine performing well for many years, please follow the following maintenance procedures.

Always confirm that the machine is unplugged prior to performing any maintenance or repairs. 1) Unplug machine as soon as you are done using it. 2) Check power cord for any damage. If any damage is detected, replace the cord immediately. 3) Lubricate casters with a water resistant lubricant every month 4) Check machine for loose or missing nuts and bolts, and replace as necessary. 5) Check the filter, and clean it after each use 6) Remove the vacuum hose and check it for any holes and clogs 7) Clean the outside of the machine with a mild cleaner.

STORAGE
1) Unplug machine from power source and wrap cord on handle.
2) Store in upright position in a dry area.
3) Store with squeegee assembly off the ground. 4) Store with clear window off unit so that tank may breathe.

iW90

6

OPERATOR

MACHINE COMPONENTS

1.Handle 3.Knob 5.3.5″ Caster 7.Hose Assy 9.Clear Window 11.Drain Hose 13.Wire Hook

2. Crevice Tool 4. 10″ Wheel 6. Front mount squeege 8. Tank 10. On/off switch 12. Pedal

1 2 3
4 5
10 11
12

9 8 7 6
13

7

iW90

OPERATOR

iW90

8

OPERATOR

PARTS LIST

DIA PART NO NUMBER

DESCRIPTION

1

2320202 Handle

2

2310126 Clamp, Crevice

3 2320405U Cord

4 6210519U Power Cord

5

2110108 Switch

6

1313325 Screw, ST4.8 X 25

7

2320409 Power Cord

8

2320411 Cable Fixing Head

9

4020310 Strain Relief

10 1221510 Screw,Ph, M5 X 10

11 2320401 Panel, Switch

12 2320220 Bend

13 2320229 Float,Shut off

14 2320216 Clear Window

15 2320218 Gasket, Clear Window

16 1321225 Screw,Ph,ST4.2 X 25

17 2320217 Rubber Hinge

18 1421409 Washer,Plain,4.3X9X0.8

19 1321210 Screw, Ph, St4 X10

20 1221410 Screw, Ph, M4 X10

21 2320241 Bracket,Right,Handle

22 4010316 Logo

23 1222510 Screw,Fh, M5 X10

24 2420006 Hose Housing

25 2020202 Gasket,Intake

26 2320201 Tank

27 2320210 3.5″ Caster

28 1421618 Washer,Plain,6.4X18X1.6

29 1021616 Screw,Hex, M6 X16

30 2320211 Axle

2320223 Wheel,10″ 31
2320228 Wheel,10″

2320312 Washer,Wheel,Al 32
1421132 FLAT WASHER 13×32×1.5 33 1421622 Washer,Plain,6.6X22X2

34 1962050 Clamp, 27~51

SERIAL NUMBER
000000-105359 105360000000-105359 105360-

9

NO REQ’D
1 1 1 1 1 2 1 1 1 4 1 1 1 1 1 4 1 11 5 2 1 2 8 1 1 1 2 4 6 1 2 2 2 2 2 1
iW90

PARTS LIST

DIA

PART

NO NUMBER

DESCRIPTION

2230130 Drain Hose 35
2320248 Drain Hose

36 1221514 Screw, Ph, M5 X14

37 2310128 Clamp, Straight Tube

38 2320603U Serial Decal

39 2310131 Supportor,Pick-up Tool

40 2030414 Warning Decal

41 2310130 Clamp, Pick-up Tool

42 2320240 Bracket,Left, Handle

43 2310127 Clamp, Bend Tube

44 1221520 Screw, Ph, M5 X20

45 2310125 Clamp, Hose

46 2310129 Clamp, Dusting Tool

47 6150711 Stainless Steel Clip

48 2230131 Plug

49 2320219 Knob

50 1422026 Washer, Lock,10 51 1421020 Washer,Plain,10.5X20X2 52 1436010 Retaining Ring, 10

53 2320207 Plate

54 2320419 Decal,Panel

55 6210123 Connector

56 7000283 Cap

57 2320415 Warning Decal

58 1422411 Lock Washer M4

59 1221412 Screw M4X12 60 1436013 Retaining Ring, 13

61 1422616 Lock Washer M6

SERIAL NUMBER 000000-000534 000534-
000000-000534
000000-105359

OPERATOR
NO REQ’D
1 1 16 2 1 1 1 2 1 2 8 4 1 2 1 2 4 4 4 1 1 1 2 1 2 2 2 2

iW90

10

OPERATOR

11

iW90

PARTS LIST

DIA PART NO NUMBER

DESCRIPTION

1 2320500 Hose Assy

2 2230121 Machine End

3 2320501 Threaded Insert

4 2230123 Clip Ring

5 2320502 Hose

6 6210114 Coupler, 38mm

7 2320208 Acoustic Insulstion Pipe

8 1914300 Tie, Cable

9 1221616 Screw, Ph, M6 X16

10 2320214 Leaf Spring

11 2320304 Knob, Floor Tool

2320311 26″ Blade(PU) 12
2320309 26″ Blade(Optional)

13 1221514 Screw, Ph, M5 X14

14 2320303 Clamp, Blade

15 1321310 Screw, Ph, St4.8 X10

16 1421618 Washer,Plain,6.4X18X1.6

17 1021825 Screw,Hex, M8 X25

18 1439005 Retaining Ring, 5

19 2320308 2″ Wheel

20 2320306 Axle, 2″ Wheel

21 2320302 Bumper

22 2320301 26″ Body,Pick-Up Tool

23 2320215 Mounting Plate, Floor Tool

24 2320212 Axle, Mounting Plate

25 1421020 Washer,Plain,10.5X20X2

26 1436010 Retaining Ring, 10

27 2320213 Axle, Pedal

28 2320209 Pedal

29 2320411 Strain Relief

30 2320203 Bottom Plate, Assy

31 1422616 Washer, Lock,6

32 2310123 Filter

33 2310118 Gasket

34 1123608 Nut, Lock, M6

35 1421617 Washer,Plain,6.2X16X2

iW90

SERIAL NUMBER

OPERATOR
NO REQ’D
1 1 1 1 1 1 1 1 5 1 2 2 2 4 1 2 4 2 4 2 2 2 1 1 1 6 6 2 1 1 1 5 1 2 3 8
12

OPERATOR

PARTS LIST

DIA PART NO NUMBER

DESCRIPTION

SERIAL NUMBER

NO REQ’D

2310121A

Vac Motor,3-Stg,120V,With Terminal

000101-000150;000153-000592;105360-

1

36

8011025A

Vac Motor,2-Stg,120V,With Terminal

000593-003583;103584-105359

1

2310122 Stud,Vac Motor 3-Stg

Match the serial number of Vac Motor 3-Stg

3

37

8112006 Stud,Vac Motor 2-Stg

Match the serial number of Vac Motor 2-Stg

3

38 1121605 Nut, M6

3

39 2310116 Gasket,Vac Motor

1

40 2310120 Screen

1

41 2320308A 2″ Wheel Assy

2

NOTES: 1,DIA NO 36,2310121A and 6210163A belong to the same specifications,the same electrical parameters and installation structure,can be used instead. After-sales spare parts, our delivery part number should be subject to the actual inventory at that time. 2,Use part number 8011025A for all the 2-stage serial numbers
and part number 2310121A for all the 3-stage serial numbers.

13

iW90

ACCESSORIES

OPERATOR

iW90

14

OPERATOR

PARTS LIST

DIA

PART

NO NUMBER

DESCRIPTION

1

2320300 26″ Front Mount Squeegee Assy

2

2330120 Hose, Vacuum Assy

3

2230124 Angeled Hose End, 38mm

4

2230122 Threaded Insert

5

2230123 Clip Ring

6

2330122 Hose

7

2330121 Hose End

8

2230115 Wand

9

2230116 Tube, SST

10

2230126 Dusting Tool

11

2230127 Crevice Tool

12

2230106 Dry Pick-Up Tool, 360mm

13

2230107 Wet Pick-Up Tool, 360mm

14

2230117 Body,Pick-Up Tool 360mm

15

2130101 Wheel, Assy

16

2130102 Axle, Wheel

17

2230109 Seat, Rubber Blades,Back

18

2230110 Seat, Rubber Blades,Back

19

2230111 Brush Strip, Back

20

2230112 Brush Strip, Front

21

2230113 Rubber Blade, Back

22

2230114 Rubber Blade, Front

2330130 Cloth Bag 23
2330132 Paper Bag(optional)

24

2330131 Clip, Cloth Bag(optional)

25

2330134 Catridge Filter

26

1962052 Clamp

SERIAL NUMBER

NO REQ’D
1 1 1 1 1 1 1 1 2 1 1 1 1 1 2 2 1 1 1 1 1 1
1
1
1 1 1

15

iW90

OPERATOR

TECHNICAL DATA

Model

iW90

Voltage

120V

Power

1000W

Current

9A

Frequency

50-60Hz

Capacitor

90L

Vacuum

2319mmH2O(91″)

Flow rate

2910L/Min(104CFM)

Sound pressure level at workstation

70 dB(A)

Weight

40kg

Length of Power cord

15m

Dimensions

117.6cm(L)X45.3cm(W)X110cm(H)

iW90

16

OPERATOR
Wiring Diagram iW90

120V 60HZ SINGLE PHASE
SUPPLY

SWITCH BLACK
WHITE
G

BROWN BLUE G/Y

SJTW 14/3C
POWER SUPPLY CORD

Motor

17

iW90

WEAR &TEAR PARTS

DIA PART NO NUMBER

1

2320210 3.5″ Caster

2

2320228 Wheel,10″

3

2320309 26″ Blade

4

2320308 2″ Wheel

5

2230126 Dusting Tool

6

2230113 Rubber Blade, Back

7

2230114 Rubber Blade, Front

8

2230127 Crevice Tool

DESCRIPTION

OPERATOR
NO REQ’D
2 2 2 2 1 1 1 1

iW90

18

CERTIFICATE OF QUALIFIED

MODEL : INSPECTOR :

SERIAL NO.: DATE :

ICE Cobotics(GuangDong)Company Limited

(TEL): (769) 8186 9000

(FAX) : (769) 8186 3000

References

• icecobotics.com