Ice I28btl Automatic Scrubber Instruction Manual (+ PDF)

Contents hide

1 i28BTL Automatic Scrubber

2 Product Information:

3 Product Usage Instructions:

3.1 Documents / Resources

3.1.1 References

i28BTL Automatic Scrubber

Product Information:

This product is an automatic scrubber manufactured by ICE
Companies. It is designed for commercial use and is intended for
scrubbing hard floors in indoor environments. The product is part
of the Intelligent Cleaning Equipment (ICE) series and comes in
three models: i28BTL+, i28BTL+-CY, and i32BTL+.

The parts list, safety precautions, and machine components are
provided in the user manual. The manual also includes information
on how to order parts, warranty protection, and environmental
considerations for disposing of packaging materials and old machine
components.

Contact information for ICE Company Limited is provided for
customer support and inquiries.

Product Usage Instructions:

Ensure you have read and understood the operator manual before
operating the machine.
Only use recommended accessories for the machine.
Do not operate the machine unless you have been trained and
authorized.
Avoid operating the machine in flammable or explosive
areas.
Make sure all safety devices are in place and operating
properly before starting the machine.
Avoid using flammable materials in the machine’s tanks.
Do not pick up flammable materials or reactive metals with the
machine.
Before leaving or servicing the machine, stop it on a level
surface and turn it off.
Read the operator’s manual thoroughly before servicing the
machine.
Use manufacturer supplied or approved replacement parts for
servicing.
Secure the machine with wheel blocks before jacking it up for
servicing.
Use an approved jack or hoist to safely elevate the machine
during servicing.
Disconnect batteries prior to working on the machine.
Avoid moving parts and do not wear loose fitting clothing while
servicing the machine.

View Fullscreen

www.icecompanies.com
www.ice4usa.com

PARTS LIST
Operator & Parts Manual
i28BTL+ i32BTL+

Automatic Scrubber

INTELLIGENT CLEANING EQUIPMENT
ICE i28BTL+ / i28BTL+-CY / i32BTL+

8210042 REV.04 (05-2021)
1

PARTS LIST
READ OPERATOR MANUAL CAREFULLY!
IMPORTANT: To ensure full warranty protection, please fill out & return your warranty card.
Please fill out at time of installation for future reference. Model No. Serial No. Machine Options Sales Rep. Sales Rep. Phone No. Customer ID Number Installation Date
HOW TO ORDER PARTS Only use ICE Company supplied or equivalent parts. Parts and supplies may be ordered online,by phone, by fax or by mail. 1. Identify the machine model. 2. Identify the machine serial number from the data label. 3. Ensure the proper serial number is used from the parts list. 4. Identify the part number and quantity.
Do not order by page or reference numbers. 5. Provide your name, company name, customer ID number,billing and shipping address,
phone number and purchase order number.
PROTECT THE ENVIRONMENT Please dispose of packaging materials,old machine components such as batteries, hazardous fluids, including antifreeze and oil, in an environmentally safe way according to local waste disposal regulations.
Always remember to recycle.

ICE Company Limited XiangShi Road LiaoBu DongGuan GuangDong China Tel: 0769 – 81869000 Fax:0769 – 81863000

Specifications and parts are subject to change without notice.

ICE i28BTL+ / i28BTL+-CY / i32BTL+

TABLE OF CONTENTS

PARTS LIST

SAFETY PRECAUTIONS…………………………………………………………………………………………4 MACHINE COMPONENTS………………………………………………………………………………………5 PANEL COMPONENTS………………………………………………………………………………………6 i-synergyTM INTRDUCTION……………………………………………………………………………………7 MACHINE SETUP & INSTALLATION…………………………………………………………………………7 MACHINE OPERATION…………………………………………………………………………………….8 WHILE OPERATING MACHINE………………………………………………………………………………8 TANK DRAINING……………………………………………………………………………………………………9 BATTERY CHARGING…………………………………………………………………………………………..10 PREVENTATIVE MAINTENANCE…………………………………………………………………………..10 FAULT CODE & SOLUTION……………………………………………………………………………………11 BASIC TROUBLESHOOTING………………………………………………………………………………..12 TECHNICAL SPECIFICATION………………………………………………………………………………..13 PARTS LIST………………………………………………………………………………………………..14-31 WEAR AND TEAR PARTS…………………………………………………………………………………….32 WIRING DIAGRAM……………………………………………………………………………………………….33

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

SAFETY PRECAUTIONS
This machine is intended for commercial use. It is designed exclusively to scrub hard floors in an indoor environment and is not constructed for any other use. Only use recommended accessories.

WARNING: Fire or Explosion Hazard. Keep sparks and open flames away! Keep battery compartment open when charging.

All operators shall read, understand and exercise the following safety precautions:
1. Do not operate machine: – Unless trained and authorized. – Unless you have read and understand the operators manual. – In flammable or explosive areas. – If not in proper operating condition. – In outdoors areas.
2. Before starting machine: – Make sure all safety devices are in place and operate properly.

WARNING: Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks.
WARNING: Flammable materials or reactive metals can cause explosion or fire. Do not pick up.

3. When using machine: – Go slow on inclines and slippery surfaces. – Follow all safety guidelines. – Be very careful when using the machine in reverse. – Reduce speed when turning. – Report and fix any damage to machine prior to operating it. – Never allow children to play on or around. – Do not operate on inclines that exceed 5% (3°).

4. Before leaving or servicing machine: – Stop on level surface. – Turn off machine.

5. When servicing machine: – Read operators manual thoroughly prior to operating or servicing this machine. – Use manufacturer supplied or approved replacement parts. – Secure machine with wheel blocks prior to jacking the machine up. – Use approved jack or hoist to safely elevate the machine. – Disconnect batteries prior to working on machine. – Avoid moving parts. Do not wear loose fitting clothing while servicing machine.
4

ICE i28BTL+ / i28BTL+-CY / i32BTL+

MACHINE COMPONENTS

PARTS LIST

17 18 19 20 21

25 4

9 10 11 12 13 14 15 16

29 30 31 32 33 34

1. Control handle 2. Control panel (See penal components) 3. Recovery tank drain hose 4. Emergency stop button 5. Circuit breaker, Controller 6. Circuit breaker, Brake 7. Hose fill port 8. Squeegee lift lever 9. Wheels, 8 Inch 10. Filter assembly 11. Vacuum hose 12. Solution tank level / Drain hose 13. Ball valve 14. On-board battery charger 15. Squeegee assembly 16. Caster, 2 inch, Squeegee adjustment 17. Control handle start bail

18. i-synergyTM, ID card scanning area 19. Lithium-ion batteries 20. Recovery tank support stand 21. Vacuum motor, 24VDC 22. Cup holder 23. Recovery tank cover 24. Recovery tank 25. ICE logo 26. Bucket fill port/ Clean-out port 27. Solution tank 28. LED light 29. Front cover 30. Brush & Pad realease plunger 31. Scrub head adjusting bolt 32. Scrub head skirt 33. Scrub head assembly 34. Parking brake (Option)

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

ANDROID LCD SCREEN

01 Date & Time 02 Battery meter 03 Setting button 04 Solution flow adjsuting button 05 Vacuum motor button 06 1-step starting button 07 Work mode select button 08 Scurb head pressure adjusting button 09 Speed adjusting button 10 Timer

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

i-synergyTM INTRODUCTION
i-synergyTM collects operational data from cleaning machines and transmit the information to ICE’s server. The ICE server generates daily reports and send them to designated end users by email. From these reports, end users will have information about machines’ usage and even specific timings. Besides, i-synergyTM also collects data on lithium-ion battery, vacuum motor, brush deck motor, transaxle, and other electrical components at least once every minute when the machine is in use and even during battery charging. i-synergyTM will send notifications instantly to the ICE server in case of any malfunction. ICE maintenance personnel will receive a SMS within minutes from the ICE server for immediate servicing.
MACHINE SET UP & INSTALLATION

4. Plug the batteries connector to the machine adaptor, connect machine i-synergyTM COM port with the batteries. MACHINE SET UP
PRE-OPERATION CHECKS 1. Sweep or dust mop the surface to be cleaned. 2. Check battery meter to make sure batteries are
fully charged. (See BATTERY CHARGING) 3. Check that squeegee is properly installed. 4. Check that brushes / pads is properly installed.
INSTALLING BRUSHES OR PADS 1. Turn off the 1-Step scrub head up/dwon button
(Panel components, item #12) and Raise the Scrub head off the floor, then stop machine on the level surface, ensure the machine is turned off. 2. If using the Pad Driver, first attach the appropriate pad to the pad driver surface. 3. Align the pad driver or brush under the motor hub and push it upward to engage.

UNCRATING MACHINE
Be sure and check packing carton for any damage. Immediately report any damage to carrier. Check the contents of package to ensure that the following items are included:
· Machine · Lithium-ion Batteries · Squeegee assembly · 2-Pad Drivers

INSTALLING BATTERIES
The machine uses the Lithium-ion batteries, the batteries are already in the machine upon delivery; However you will need to connect the Lithium ion batteries to the machine.
WARNING: Fire or Explosion Hazard. Keep sparks and open flames away! Keep battery compartment open when charging.
1. Turn off the machine. 2. Open recovery tank to gain access to battery
compartment. 3. Carefully place the Lithium-ion batteries into the
compartment. Place the battery brace at the rear of the batteries. DO NOT DROP BATTERIES INTO COMPARTMENT!

4. To remove the pad driver or brush, raise the scrub head and push the pad release plunger (Machine components, item #30) downward.
MOUNTING THE SQUEEGEE ASSEMBLY 1. Lift the squeegee lift lever (Machine
components, item #8)to the upward position. 2. Mount the squeegee assembly to the squeegee
pivot bracket. make sure the knobs are completely seated into the slots before securing knobs. 3. Connect the vacuum hose to the squeegee assembly. Loop the hose by using the hose clip provided. 4. Check the squeegee blades for proper adjustment.

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

FILLING THE SOLUTION TANK The machine is equipped with a hose fill-port (Machine components, item #7) at the rear of the machine, and a bucket fill-port (Machine components, item #26)located under the recovery tank. Before accessing the bucket fill-port make sure that the recovery tank is empty.
Fill the solution tank to the “100L” level on the solution tank sight gauge. When using the bucket fill-port, stop filling when the level reaches the bottom edge of the fill-port.
NOTE: When filling the solution tank with a bucket, make sure that the bucket is clean. Do not use the same bucket for filling and draining the machine.
WARNING: Do not put any flammable materials into solution tank. this can cause an explosion or a fire. Only use recommended cleaning chemicals. Contact your janitorial supply distributor for recommendations on proper chemicals.
MACHINE OPERATION
WARNING: Do not operate machine unless you have read and understand this manual. 1. Swipping the ID card (Machine components,
item #18) to turn on the machine. 2. Check the LED display screen (Panel
components, item #4), if there are fault condes (Panel components, item #18) and the Fault indicator (Panel components, item #1) in blink, please DO NOT operate the machine unless the faults have been eliminated (please see FAULT CODES AND ELIMINATE section). 3. Turn on the 1-Step scrub head up/down button, the scrub head will be lowered down automatically. 4. Lower squeegee assembly to the floor by lowering the Squeegee lift lever. 5. Check the solution flow indicator (Panel components, item #9), press the Solution flow adjusting button (Panel components, item #10) to get a desired solution flow. NOTE: Solution will not begin to flow until the control handle bail is pulled. 8

6. Turn on the Vacuum motor switch(Panel components, item #8).
7. Pull the Control handle bail (machine components, item #17) backwards to start scrubbing .The machine will automatically propel forward. To reverse the machine, simply push the control handle bail forward. NOTE: Raise squeegee when reversing machine.
8. The scrubbing speed can be adjusted, press the Speed increase/ decrease button (Panel components, item #14, #16) to a desired speed. NOTE: 45-60 meters (150-200 ft)per minute is the recommended scrubbing speed.
9. The brush pressure can be adjusted, press the Brush pressure increase/ decrease button (Panel components, item #3,#6) to get a desired brush pressure.
10. To stop scrubbing, release the control handle bail, turn off the 1-Step scrub head up/down button to raise he scrub head assembly, raise the squeegee assembly.
WHILE OPERATING MACHINE
WARNING: Fire Or Explosion Hazard. Do Not Pick Up Flammable Materials Or Reactive Metals. 1. Go slow on inclines and slippery surfaces. Do
not operate the machine on inclines that exceed 5% (3°). 2. Do not keep the machine in the same position with pad / brush spinning, keep the machine moving to prevent damage to floor finish. 3. If the squeegee assembly leaves streaks on the floor, raise the squeegee off the floor and wipe the blades down with a damp cloth. Pre-sweep the area to prevent leaving streaks on the floor. 4. Pour a recommended defoamer into the recovery tank if excessive foam appears.
WARNING: Do not allow foam to enter the float shut-off screen, vacuum motor damage will result. Foam will not activate the float shut-off screen.
5. Occasionally check the battery meter(Panel components, item #2). when the battery is very low, stop scrubbing and recharge the batteries.
WARNING: When battery meter is in the red, do not continue to operate the machine. Battery damage may result.
ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

6. When the solution tank runs empty, press the 1-Step switch raise the brush head. Keep the squeegee down and continue to vacuum until all the dirty water is picked up. NOTE: Brush motors will not work when the scrub head assembly raised.
NOTE: See TANK DRAINING section to learn how to drain recovery and solution tanks.
CIRCUIT BREAKER / FUSES The machine is equipped with 2 resettable circuit breakers(machine components, item #5, item# 6) to protect the main controller from damage. If the circuit breakers should trip, it can’t be reset immediately. You must first determine what caused the breaker to trip, and allow the motor to cool down and then you can manually reset the circuit breakers.

TANK DRAINING
1. Turn the machine off. 2. With the squeegee and scrub head in their “up”
position, transport machine to approved area for draining tank(s).
DRAINING THE RECOVERY TANK Any time scrubbing is completed, or when refilling solution tank, the recovery tank should be drained and cleaned.
WARNING: If the recovery tank is not drained when the solution tank has been refilled, foam or water may enter the float shutoff screen and cause damage to the vacuum motor.

The machine is also equipped with a 150A fuse to protect the Lithium-ion batteries from damage. When replacing a fuse never substitute a higher Amps rated fuse than specified.
HOUR METER The hour meter (Panel machine components, item #17) records the number of total hours the brush motor has been powered on. Use the hour meter to determine when to perform recommended maintenance procedures and to record service history.
EMERGENCY STOP BUTTON/ BRAKE The machine is equipped with an Electromagnetic Brake Mechanism on the Transaxle. When in case of Emergency, release the Control Handle bail or strike the Emergency stop button (Machine components, item #4), the machine will be braked and then stop. Reset the emergency stop button, turn on the machine, and then pull the control handle bail, the machine will be restart.
NOTE: The machine can not be moved unless the Main Power and the Control Handle bail be turned on.
WARNING: Do Not Change the Default Settings of the Electromagnetic Brake Mechanism unless Authorized, otherwise it may cause Machine Damage or Personal Injury. Contact the Authorized Service center for machine repairs.

1. While holding the drain hose (Machine components, item #3) upward, remove the cap and lower hose to drain.
2. Open the recovery tank cover and rinse out the tank. Use a rag to remove any excess dirt.
3. Clean the float shut-off screen and debris tray located in the recovery tank .
DRAINING THE SOLUTION TANK Any time scrubbing operation is completed, the solution tank should be drained and cleaned. 1. Pull the solution tank level hose(Machine
components, item #12) off the hose fitting, this will allow the solution to flow freely into a bucket or floor drain. 2. Remove the cover of the filter assembly (Machine components, item #10) to drain the solution tank, check the filter screen and clean up it if necessary. 3. Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lines. 4. After rinsing out the tank, securely reconnect the tank level hose to the hose fitting, replace the filter assembly cover and be sure the filter screen and the “O” ring is in the correct position.

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

BATTERY CHARGING
WARNING: Fire Or Explosion Hazard. Keep Sparks and Open Flame Away. Keep Battery Compartment Propped Open When Charging. Only use ICE supplied or approved batteries charger, use unapproved charger may cause damage to the batteries and machine. Batteries chargers specifications: · Applicable to charging Lithium-ion batteries · Automatic shut off circuit · Output current of 30 Amps · Output voltage of 24 volts
1. Place machine in a well ventilated area. 2. Turn the machine off. 3. Connect the charger’s AC power supply cord to
a properly grounded receptable. 4. Prop up the recovery tank by the support stand
(Machine components, item #20) for ventilation when charging. 5. The charger will automatically begin to charge and will automatically shut off once the batteries are fully charged. 6. Upon completion of charging, disconnect the AC power supply cord.
PREVENTATIVE MAINTENANCE
WARNING: Before performing any maintenance on the machine, be sure that the power is turned off, or the batteries are disconnected!

3. Raise the squeegee assembly off floor and wipe it down with a damp towel. Be sure to store the squeegee in the up position.
4. Remove the float shut-off assembly and rinse it out with clean water.
5. Clean machine with an approved cleaner and a damp towel.
6. Recharge the batteries. 7. Check the condition of the squeegee blade
wiping edge, rotate blade if worn.
MONTHLY MAINTENANCE 1. Clean the battery tops to prevent corrosion. 2. Check for loose battery cable connections. 3. Inspect and clean the recovery tank cover seal.
Replce it if damaged. 4. Lubricate all grease points and pivot points with
silicon spray and approved grease. 5. Check the machine for loose nuts and bolts. 6. Check the machine for leaks.
MACHINE STORAGE 1. Always store the machine indoors. 2. Always store the machine in a dry area. 3. Always store the machine in its upright position. 4. Always store the machine with the pad driver/
brush raised off the floor. 5. Always store the machine with the squeegee
assembly raised off the floor. 6. If storing in an area which may reach freezing
temperatures, be sure to drain all fluids from the machine prior to storage. Any damage caused by freezing temperatures will not be covered by the warranty. 7. Drain the recovery tank. 8. Drain the solution tank of all fluid.

WARING: Repairs are to be completed by Authorized service centers only. Any repairs completed by unauthorized persons will avoid the warrenty.
DAILY MAINTENANCE 1. Remove pad driver/ brush and clean with
approved cleaner. 2. Drain recovery and solution tanks completely
and rinse out with clean water. Visually check the recovery tank for debris and clean out as necessary.
10

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

FAULT CODE & SOLUTION

The machine is equipped with a LED display screen Once fault occuring, please DO NOT continue

(Panel components, item # 4), the LED screen will operate the machine unless the fault are eliminated.

display the operating hours (Panel components, Turn off the machine, then to solve the fault, the

item # 17) and the battery level status (see Panel fault code & message will be eliminated when

components, item # 2).

machine restart.

When the machine detects a fault, there will be a

Fault code (Panel components, item #18) & Fault If the fault is occurred frequently, or the fault can’t

message (Panel components, item #11) display be eliminated, please contact ICE service center.

on the LED screen, and the Fault indicator (Panel

components, item #1) will flash continuously,

Please refer to the below table to determine the

accompany an audible alarm Occasionally.

fault cause and the solution.

FAULT CODE
F03 F04 F05 F06 F07 F08 F10 F11

FAULT MESSAGE
Bru Actt O.L. RESTART! Vac Mtr O.L. RE-START! Left Bru Mtr O.L. RE-START! Right Bru Mtr O.L. RE-START! Propel Mtr O.L. RE-START!
RecTank Full
Batt Low Charge Batt Batt Empty Charge Batt NOW

FAULT CAUSE

SOLUTION

Scrub head lifting actuator is overload

Vacuum motor overload Left brush motor is overload Right brush motor is overload

Turn off the machine,after a moment, RE-START machine.

Propel motor overload Recovery tank is full Battery is low

Drain the Recovery tank Charge the battery

Battery is empty

Charge the battery NOW

F12

Brake Wiring Error

Bad Brake wiring

Check the brake wiring

F14

Replace Brake Assy Bad Brake assembly

F16

Control Unit Overheat! Wait

Control Unit Overheat

F17

Replace Control Unit Control Unit Fault

F20 Check Left Brush motor Bad left brush motor

F21

Check Vac Mtr

Bad Vacuum motor or wiring

F22

Check Soln Solenoid Solution solenoid wiring fault

F23

Replace Soln solenoid Bad Solution solenoid

F24

Check Propel Motor Bad propel motor

F25 Check Right Brush motor Bad right brush motor

F40

Check Proximity Sw Proximity switch fault

F41

Release Handle

Operation mistake

F42

Replace Control Unit Bad Control Unit

F43

Turn Dead Sw Off RE-START!

Emergency stop button activated

F44

Replace Control Unit

F45

Return Control Unit

F46

Return Control Unit

Bad Control Unit

F47

Return Control Unit

F48

Return Control Unit

Replace the brake assembly Turn off the machine,after a moment, RE-START machine Replace the control unit Check left brush motor/ wiring Check the vacuum motor / Wiring Check the wiring & Contactors Replace the solution solenoid Check the propel motor / Wiring Check right brush motor/ wiring Check the Proximity switch Release the control handle bail Replace the control unit Release emergency stop button and restart machine
Contact service center, Replace the Control Unit

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

BASIC TROUBLESHOOTING

PROBLEM

CAUSE

SOLUTION

Control handle bail not pulled

Pull control handle bail

Batteries need to be charged

Charge batteries

Machine will not Bad lithium-ion batteries

operate

Emergency stop button activated

Replace batteries Reset Emergency stop botton

Main PCB fuse blown Faulty i-synergyTM module

Contact ICE service center Contact ICE service center

1-STEP scrub head up/down switch is off

Battery meter lockout activated

Brush motor not operate

will

Faulty

control

handle

bail

switch

Faulty brush motor or wiring

Turn on the 1-STEP switch Recharge batteries Contact ICE service center Contact ICE service center

Worn Motor carbon brushes

Contact ICE service center

Machine does not propel

the Control handle bail not pulled Faulty transaxle motor or wiring Worn Motor carbon brushes

Pull the control handle bail Contact ICE service center Contact ICE service center

Vacuum motor Faulty vacuum motor or wiring will not operate Worn Motor carbon brushes

Contact ICE service center Contact ICE service center

Ball valve set too low or shut off

Solution flow control knob set too low or

Little or no solu- shut off

tion flow

Clogged solution tank filter or solution

hose

Clogged solution Solenoid valve

Turn on the ball valve Adjust solution control flow knob
Clean solution tank filter or flush out solution hose Remove valve and clean

Recovery tank is full

Drain recovery tank

Loose drain hose cap

Tighten cap

Clogged float shut-off screen located in recovery tank
Clogged squeegee assembly

clean screen Clean squeegee assembly

Worn squeegee blades

Replace or rotate squeegee blades

Poor water pick Incorrect squeegee blade deflection

Loose vacuum hose connections

Clogged vacuum hose

Adjust squeegee blade height Secure hose connections Remove clogged debris

Damaged vacuum hose

Replace vacuum hose

Recovery tank cover not in place

Properly position cover

Damaged recovery tank cover seal

Replace seal

Faulty vacuum motor

Contact ICE service center

Low battery charge

Recharge batteries

Low battery charge

Fully recharge batteries

Defective batteries

Replace batteries

Short run time Batteries need maintenance Faulty battery charger

See BATTERY MAINTENANCE Repair or replace battery charger

Down pressure lever is set for extra scrub Lower down pressure lever head pressure

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

TECHNICAL SPECIFICATIONS

MODEL

i28BTL+-CY

i28BTL+

DIMENSIONS – L

61.02 in / 1,550 mm

DIMENSIONS – W

30.51 in / 775 mm

DIMENSIONS – H

44.49 in / 1,130 mm

WEIGHT

352.74 lbs / 160 Kg

WEIGHT WITH BATTERIES

661.39 lbs / 300 Kg

SOLUTION TANK CAPACITY

26.42 Gal / 100 L

RECOVERY TANK CAPACITY

31.7 Gal / 120 L

i32BTL+ 62.21 in / 1,580 mm
34.06 in / 865 mm 44.49 in / 1,130 mm 374.79 lbs / 170 Kg 683.43 lbs / 310 Kg

SQUEEGEE WIDTH

Standard: 40.5 in / 1,030 mm Option: 44.5 in / 1,130 mm

Standard: 46.5 in/1,185 mm Option: 44.5 in / 1,130 mm

CLEANING PATH WIDTH PRODUCTIVITY RATE DRIVE SYSTEM TRAVEL SPEED, MAXIMUM MINIMUM AISLE TURN PAD/BRUSH PRESSURE
SOLUTION FLOW RATE

28 in / 700 mm

32 in / 800 mm

30,667 ft2 / 2,850 m2 h

34,983 ft2 / 3,250 m2 h

Transaxle, 24VDC, 0.27 hp / 200 W

Cleaning: 65 m/Min 213.25 ft/min

Transporting: 72 m/Min 236.22 ft/Min

0 ~ 79.37 lbs 0 ~ 36 kg

63 in / 1600 mm
39.68 lbs / 18 kg 79.37 lbs / 36 kg 119.05 lbs / 54 kg
0 ~ 0.66 Gal / Min 0 ~ 2.5 L/Min

BRUSH / CYLINDERICAL MOTORS

0.75 hp / 560W × 2, 750 RPM

0.75 hp / 550W × 2, 210 RPM

BRUSH / CYLINDERICAL DIMENSIONS (x2)
VACUUM MOTOR WATER LIFT – AIR FLOW
BATTERIES
RUN TIME PER CHARGE VOLTAGE DC DECIBEL RATING AT OPERATOR’S EAR, INDOORS GRADE LEVEL, MAX
13

Dia: 150 mm / 6 in

Diameter:

Length: 700 mm / 28 in 355.6 mm / 14 in

Diameter: 406.4 mm / 16 in

0.8 hp / 600 W 65 in / 1650 mm Lithium-ion Batteries, 240 AH
3.5~4 Hours 24 V

68 dB(A)

5% (3°) ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

RECOVERY TANK GROUP

ICE i28BTL+ / i28BTL+-CY / i32BTL+

DIA PART NO. NUMBER

8111001

8131003

8210102

8131010

1962050

8111300

1421618

1021616

8210207

1421612

8112005

1121605

8210209

8210260 14
8132006

1123608

1914300

8132007

4010316

8111008

1421816

8111007

8115404

1021830

8111016

1221512

8111015

8111014

8210201

8011005

8210103

8111022

8310238

RECOVERY TANK GROUP
DESCRIPTION
GASKET CAP RECOVERY TANK DRAIN HOSE CLAMP HINGE ASSEMBLY FLAT WASHER M6×18×1.6 HEX BOLT M6 X 16 CABLE FLAT WASHER M6×12×1.6 GASKET, VACUUM MOTOR HEX NUT M6 STUD M6×110 AMETEK VACUUM MOTOR 24VDC, KIT CARBON BRUSH, VACUUM MOTOR LOCK NUT M6 TIE, NYLON, 5X300 MUFFLER, VACUUM MOTOR ICE LOGO BRACKET FLAT WASHER M8×16×1.6 RECOVERY TANK SUPPORT SLEEVE, P/M HEX BOLT M8×30 PLATE SCREW M5×12 FLOAT, SHUT-OFF FLOAT ADAPTER RECOVERY TANK COVER SEAL CAP RECOVERY TANK COVER WARNING LABEL SENSOR, SOLUTION LEVEL

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST
NO REQ’D
1 1 1 1 1 2 10 12 1 5 1 3 3 1 2 3 1 1 1 1 2 1 1 1 2 2 1 1 1 1 1 1 1
15

PARTS LIST

SOLUTION TANK GROUP

ICE i28BTL+ / i28BTL+-CY / i32BTL+

DIA

PART

NO. NUMBER

1 6210131

2 1421510

3 1221512

4 1123507

5 8210111

6 8210117

7 1421612

8 1021616

9 8311720

10 8112030

11 1222641

12 8210112

13 1321213

14 8210113

15 8210101

16 4010316

17 8130099

18 8210145

19 1962025

20 8210151

21 N240570

22 8210104

23 1321110

24 1421409

25 8133610

26 8133601

27 1221520

28 8133602

29 8210531

30 1535630

SOLUTION TANK GROUP
DESCRIPTION
NYLON, CLAMP FLAT WASHER M5×10×1 SCREW M5×12 LOCK NUT M5 BRACKET, BATTERY CHARGER MNTG CAP, CHARGER FLAT WASHER M6×12×1.6 HEX BOLT M6 X 16 ON BOARD LI-ION BATTERY CHARGER POWER CORD, BATTERY CHARGER, US SCREW M6 X 40 HOOK, CORD SELF-TAPPING SCREW ST4.2X13 CAP, SOLUTION FILL SOLUTION TANK ICE LOGO I-SYNERGY LOGO CLEAN TUBING CLAMP 16-25mm LABEL, LEFT SIDE LITHIUM-ION BATTERY, 240AH COVER, FRONT SELF-TAPPING SCREW ST3.5 ×10 FLAT WASHER M4×9×0.8 LED LIGHT KIT LED LIGHT MNTG BASE SCREW M5X20 LED LIGHT COVER KNOB, M6 SET SCREW M6 ×30

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST
NO REQ’D
12 32 24 6 1 1 12 10 1 1 2 2 2 1 1 2 2 1 1 1 1 1 3 5 1 1 3 1 2 2
17

PARTS LIST

DIA

PART

NO. NUMBER

31 1421618

32 8113112

33 8210152

34 8113030

35 8113002

36 8113007

37 8210168

38 8210163

39 8210723

40 8210724

41 8210164

42 1422515

43 1021512

44 1221525

SOLUTION TANK GROUP
DESCRIPTION
PLAIN WASHER 6×18×1.6,SS BUSHING LABEL, RIGHT SIDE SEAL COVER STRAP PLATE CONNECTOR HOUSING BATTERY CONNECT CABLE, RED BATTERY CONNECT CABLE, BLACK BRACKET, CONNECTOR SPRING WASHER,M5 HEX HEAD SCREW, M5X12 PAN HEAD SCREW, M5X25

NO REQ’D
4 2 1 1 1 1 2 1 1 1 1 2 2 2

ICE i28BTL+ / i28BTL+-CY / i32BTL+

CONTROL CONSOLE GROUP

PARTS LIST

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

DIA PART NO. NUMBER

1221512

1422513

1421510

8210535 4
8210536

8210481

8134015

8134905

1221306

8134005B

8310740

8134008

8144029

8310707

8134060

8134061

1421618

1422616

1021616

8114705

8310480

1021616

8114005

1021840

1422821

1421828

1021630

8210475

8014101

1021512

1421515

1123608

8014012

CONTROL CONSOLE GROUP
DESCRIPTION
SCREW M5×12 LOCK WASHER M5 FLAT WASHER M5×10×1.0 CONTROL PANEL DECAL, i28BTL+ CONTROL PANEL DECAL, i32BTL+ CONTROL PANEL GASKET 5″ ANDROID LCD SCREEN SCREW M3×6 CONTROL HOUSING,i32BTL CIRCUIT BREAKER, 5A PLATE, EMERGENCY STOP MNTG DECAL, EMERGENCY STOP EMERGENCY STOP BUTTON PLATE, ON BOARD BATTERY CHARGER CLEAR COVER PLAIN WASHER M6×18×1.6,SS LOCK WASHER, M6 HEX BOLT M6 X 10 STAND-OFF, M6 FUSE,150A HEX BOLT M6 X 16 CONNECTOR HEX BOLT M8×40 LOCK WASHER M8 FLAT WASHER M8×28×3 HEX HEAD BOLT M6×30,SS CABLE, SQGE LIFT LIFTING ROPE SPACER HEX HEAD BOLT M5×12,SS FLAT WASHER M5×15×1.0 LOCK NUT M6 BAFFLE

NO REQ’D
17 6 13 1 1 1 1 1 6 1 2 1 1 1 1 1 12 20 2 2 1 5 1 2 12 2 1 1 1 2 1 3 1

ICE i28BTL+ / i28BTL+-CY / i32BTL+

DIA PART

NO. NUMBER

8113111

1121605

8134501

8134508

1421132

8134080

8113104

1221515

6210111

1023612

1423612

8210550

8134070

1421824

1021820

1221620

8134768

8134035

8114712

8124743

1434300

1021320

1123305

8134022

8114402

1521616

1534608

8134300

8114300

8114306

1535630

8114101

8313420

1221412

1411409

1422411

8310708

1221312

1111302

CONTROL CONSOLE GROUP
DESCRIPTION
NYLON FLAT WASHER 12.9×25.4×0.8 HEX NUT M6 BRACKET SLEEVE FLAT WASHER 12×32×1.5 SQUEEGEE LIFTING HANDLE BALL KNOB M8 PH SCREW M5×15,SS CLAMP, DRAIN HOSE HEX BOLT M6 X 12, COPPER FLAT WASHER M6× 12×1, COPPER MAIN CONTROLLER FOR i28BTL+/i32BTL+ REAR PLATE, CONTROL CONSOLE FLAT WASHER M8× 24×2 HEX BOLT M8×20 PH SCREW M6×20 RFID BOARD LABEL, i-SYNERGYTM CARD SCANNING MICRO SWITCH MICRO SWITCH LOCK WASHER, TOOTH, M3 SCREW M3 X 20 LOCK NUT M3 BRACKET,SWITCH BRACKET, SPRING SCREW M6X16, HEX SCOKET SET SCREW M6 ×8 LEVER, BAIL ACTUATOR SPRING SET SCREW M6 ×30 SHAFT RELAY,24VDC,120A SCREW, HEX HEAD, M4X12 WASHER , PLAIN , M4X9X0.8 LOCK WASHER M4 HORN, 24VDC SCREW, HEX HEAD, M3X12 NUT , M3

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST
NO REQ’D
1 2 1 1 1 1 1 2 1 10 10 1 1 10 10 2 1 1 1 1 4 4 4 1 1 2 4 1 1 1 1 1 2 4 4 4 1 2 2
21

PARTS LIST

FRAME & TRANSAXLE GROUP

ICE i28BTL+ / i28BTL+-CY / i32BTL+

FRAME & TRANSAXLE GROUP

DIA PART NO. NUMBER

DESCRIPTION

8211507 KNOB M8 ×60

8211505 SHOULDER SCREW,M12

1421132 FLAT WASHER 12×32×1.5

8135001 PLASTIC THRUST WASHER M12× 30×1.5

8211506 SHAFT

1123608 LOCK NUT M6

1421618 FLAT WASHER M6×18×1.6

8211503 BRACKET, SQUEEGEE

8114511 BALL JOINT M6

8211504 SHOULDER SCREW,M8

8210508 SPIRNG

8211501 BRACKET, SQGE LIFT

1121807 NUT, M8

1421824 FLAT WASHER M8×24×2

8211502 BRACKET,SQGE SWING

1123810 LOCK NUT M8

8211508 BUSHING

1123115 LOCK NUT M12

8115203 COVER, WHEEL

1021816 HEX BOLT M8 × 16

1422821 LOCK WASHER M8

1421828 FLAT WASHER M8×28×2

8225210 FOAM FILLED WHEEL, 8INCH, KIT

8225200 AIR FILLED WHEEL, 8 INCH, KIT (OPTION)

8125212 WHEEL, ANTI-SKID,8 INCH,KIT(OPTION)

1021825 HEX BOLT M8 × 25

8210123 BRACKET, TRANSAXLE MNTG

1436019 RETAINING RING 19

8125403 WOODRUFF KEY

28 8210120A TRANSAXLE, 24VDC

1022800 HEX BOLT M8 X 100

1021030 HEX BOLT M10 X 30

1421020 FLAT WASHER 10×20×2.0

8210109 4″ CASTER

1021820 HEX BOLT M8×20

8210115 ARM, SCRUB HEAD LIFTING

8210116 BUSHING

8210130 FRAME

1021855 HEX BOLT M8 × 55

1123012 LOCK NUT M10

8210186 BRACKET, PROXIMITY SENSOR

40 8134709A PROXIMITY SENSORKIT

1021616 HEX BOLT M6 × 16

8210138 SPACER (OPTION)

8210137 TOGGLE CLAMP, BRAKE (OPTION)

1021630 HEX BOLT M6 X 30

8210122 ELECTRONIC BRAKE KIT

1521512 SOCKET HEAD, M5 X 12

1421510 FLAT WASHER , M5×10×1

1422513 LOCK WASHER , M5

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST
NO REQ’D
1 1 2 2 1 7 2 1 1 4 1 1 2 12 1 11 1 1 2 2 7 2 2 2 2 4 2 2 2 1 1 8 8 2 5 2 2 1 2 8 1 1 2 2 1 4 1 3 3 3
23

PARTS LIST

SCRUB HEAD GROUP

ICE i28BTL+ / i28BTL+-CY / i32BTL+

SCRUB HEAD GROUP

DIA PART

NO. NUMBER

8210812

8210309

1021825

8210831

1421816

8210806

8210832

1123810

8210899 8210850

1655025

8210803

8210808

8210809

8220801 8210801

1022090

1421612

1422616

1021620

8210804

8210805

1421828

1422821

8220810 8218050

1221635

1221640

1421618

8210861

8210862

9000004

9050014 9050016

1321325

9000003

8116040

9040014 9040016

1111215

8210811

8210810

1421824

8115404

8116009

1021830

DESCRIPTION
PIN PIN, COTTER HEX BOLT M8 × 25 BRACKET, SCRUB HEAD LIFT, RIGHT FLAT WASHER M8×16×1.6 BRACKET, ACTUATOR MNTG BRACKET, SCRUB HEAD LIFT, LEFT LOCK NUT M8 BRUSH MOTOR, 24VDC, 550W, KIT CARBON BRUSH KEY, 5X5X25 SPACER, RUBBER KNOB, M10 SPRING HOUSING, SCRUB HEAD, i28BTL HOUSING, SCRUB HEAD, i32BTL HEX BOLT M10 × 90 FLAT WASHER M6×12×1.6 LOCK WASHER, M6 HEX BOLT M6 × 20 SPACER HUB, BRUSH DRIVE FLAT WASHER M8×28×3.0 LOCK WASHER M8 BUMPER, SCRUB HEAD, i28BTL BUMPER, SCRUB HEAD, i32BTL SCREW, M6 × 35 SCREW, M6 × 40 FLAT WASHER M6×18×1.6 RETAINER BAR SPRING, G-400S CLUTCH, G-400S BRUSH ASSEMBLY, 14 INCH, i28BTL (OPTION) BRUSH ASSEMBLY, 16 INCH, i32BTL (OPTION) SELF-TAPPING SCREW, ST5 X 25 CENTER LOCK, #3 SPACER, 6.5×14.5×7.0 PAD DRIVER, 14INCH, i28BTL PAD DRIVER, 14INCH, i32BTL HEX NUT, M16 AJUSTMENT STUD, M16 BRACKET, ROLLER MNTG FLAT WASHER M8×24×2 SLEEVE, P/M PROTECTIVE WHEEL HEX BOLT M8 × 30

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST
NO REQ’D
2 2 11 1 14 1 1 10 2 2 2 2 2 2 1 1 2 8 8 8 4 2 2 2 2 2 12 4 4 4 4 4 2 2 6 2 6 2 2 1 1 1 2 1 1 1
25

PARTS LIST

SCRUB HEAD LIFT GROUP

ICE i28BTL+ / i28BTL+-CY / i32BTL+

DIA PART NO. NUMBER
1 1123810 2 1421824 3 8210306 4 1021825 5 1422821 6 1021820 7 8210311 8 8210312 9 8210314 10 8210310 11 8210313 12 1022800 13 8210316 14 1123008 15 1022811 16 8210319 17 8210317 18 1421132 19 8210322 20 8210309 21 8210318 22 8210320 23 8210321 24 8210302 25 8210301 26 8210303 27 1421612 28 1422616 29 1021616

SCRUB HEAD LIFT GROUP
DESCRIPTION
LOCK NUT M8 FLAT WASHER M8×24×2 BRACKET, GUIDE MNTG HEX BOLT M8×25 LOCK WASHER M8 HEX BOLT M8×20 SPRING WASHER, PM BUSHING GUIDE, ROLLER ROLLER HEX BOLT M8 X 100 BRACKET, SCRUB LIFT LOCK NUT 3/8 HEX BOLT M8 X 110 SPRING BRACKET, SPRING FLAT WASHER 12×32×1.5 PIN PIN, COTTER SPRING SLEEVE BOLT, SHOULDER, 3/8 ACTUATOR, 24VDC PIN BRACKET, ACTUATOR MNTG FLAT WASHER M6×12×1.6 LOCK WASHER M6 HEX BOLT M6 X 16

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST
NO REQ’D
6 10 1 2 4 2 2 2 1 1 1 1 1 2 1 2 1 4 1 2 2 2 2 1 1 1 4 4 4
27

PARTS LIST SQUEEGEE GROUP, 40.5 INCH , i28BTL STANDARD

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

SQUEEGEE GROUP, 40.5 INCH , i28BTL STANDARD

DIA PART NO. NUMBER
1 1123810
2 1421824

DESCRIPTION
LOCK NUT M8 FLAT WASHER M8× 24×2.0

NO REQ’D
2
4

3 8116009

PROTECTIVE WHEEL

4 8115404

BEARING, JOURNAL

5 1021616

HEX BOLT M6×16

6 1421612

FLAT WASHER M6× 12×1.6

7 1121008

HEX NUT M10

8 8118300

RIGHT BRACKET

9 8310550

CASTER, 2 INCH

10 8310514

CLAMP ASSEMBLY

8310536

SQUEEGEE BLADE, REAR, LINATEX

8310546

SQUEEGEE BLADE, REAR, PU (OPTION)

12 8310561

SQUEEGEE HOSING

13 1021835

BOLT, HEX HEAD, M8×35

14 8310512

RETAINER, SQUEEGEE

8310535

SQUEEGEE BLADE, FRONT, LINATEX

8310545

SQUEEGEE BLADE, FRONT, PU (OPTION)

16 8210518

STAR KNOB M8

17 8118200

LEFT BRACKET

18 8210525

SHORT CLAMP ASSEBLY

19 1221575

SCREW M5×75

20 8118624

SHAFT

21 8118623

SPACER

22 1123507

LOCK NUT M5

23 8118109

HOLDER VACUUM HOSE

24 8131030

VACUUM HOSE

25 1962050

CLAMP

26 8310570

SQUEEGEE ASSEMBLY FOR i28BTL, 40.5 INCH, STANDARD 1

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

SOLUTION GROUP

ICE i28BTL+ / i28BTL+-CY / i32BTL+

DIA PART NO. NUMBER
1 8119005 2 8119007 3 8119006 4 8210901 5 8119100 6 8119101
8119103 7
8119105 8 1622063 9 8119102 10 1421510 11 1221512 12 8210902 13 8119002 14 8210903 15 1962016 16 1221412 17 1422411 18 1421409 19 8119003 20 1914300 21 8210904 22 8119008

SOLUTION GROUP
DESCRIPTION
BALL VALVE, G1/2 ELBOW G1/2 CLAMP TUBING ID=12MM L=330MM FILTER ASSEBLY BASE, FILTER ASSEMBLY SCREEN, FILTER, 70 MESH SCREEN, FILTER, 40 MESH (OPTION) O RING CAP, FILTER ASSEMBLY FLAT WASHER M5×10×1 SCREW M5×12 TUBING ID=12MM L=480MM ELBOW, TUBING BARB TUBING ID=12MM L=120MM CLAMP, 10-16mm SCREW M4×12 LOCK WASHER M4 FLAT WASHER M4×9×0.8 SOLENOID VALVE,24VDC TIE, NYLON, 5X300 TUBING ID=10MM L=180MM FITTING, PLASTIC, TEE

PARTS LIST
NO REQ’D
1 1 5 2 1 1 1 1 1 1 2 2 1 1 1 5 2 2 2 1 5 2 1

ICE i28BTL+ / i28BTL+-CY / i32BTL+

DIA PART NO. NUMBER
8125200 1 8225200
8225210 2 8116009
8230503 8230513 8210513 8210516 3 8220514 8220524 8310535 8310545 8230504 8230534 8210514 8210517 4 8220513 8220523 8310536 8310546 9050014 5 9050016 9040014 6 9040016 7 8216105

PARTS LIST

WEAR AND TEAR PARTS
DESCRIPTION
WHEEL, 8 INCH AIR FILLED WHEEL, 8 INCH, KIT (OPTION) FOAM FILLED WHEEL, 8INCH, KIT (OPTION) PROTECTIVE WHEEL SQUEEGEE BLADE, FRONT, LINATEX SQUEEGEE BLADE, FRONT, PU (OPTION) SQUEEGEE BLADE, FRONT, LINATEX (OPTION) SQUEEGEE BLADE, FRONT, PU (OPTION) SQUEEGEE BLADE, FRONT, LINATEX (OPTION) SQUEEGEE BLADE, FRONT, PU (OPTION) SQUEEGEE BLADE, FRONT, LINATEX SQUEEGEE BLADE, FRONT, PU (OPTION) SQUEEGEE BLADE, REAR, LINATEX SQUEEGEE BLADE, REAR, PU (OPTION) SQUEEGEE BLADE, REAR, LINATEX (OPTION) SQUEEGEE BLADE, REAR, PU (OPTION) SQUEEGEE BLADE, REAR, LINATEX (OPTION) SQUEEGEE BLADE, REAR, PU (OPTION) SQUEEGEE BLADE, REAR, LINATEX SQUEEGEE BLADE, REAR, PU (OPTION) 14″ BRUSH , i28BTL (OPTION) 16″ BRUSH , i32BTL (OPTION) 14″ PAD HOLDER, i28BTL 16″ PAD HOLDER, i32BTL BRUSH, CYLINDRICAL, 28″

NO REQ’D
2 2 2 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2

ICE i28BTL+ / i28BTL+-CY / i32BTL+

PARTS LIST

ICE i28BTL+ / i28BTL+-CY / i32BTL+