Minka Lavery 3860-695 Windward Passage 8 Light Island Chandelier Instruction Manual

3860-695 Windward Passage 8 Light Island Chandelier

Product Information

The product is item#3860-xxx, which is a lighting fixture. The
product comes with a mounting plate, ground screw, and mounting
screws. Additionally, the product includes two sets of rods and a
candle cover. The fixture wires are black or smooth, white or
ribbed, and bare copper for ground. The house wires are black for
hot, white for neutral, and green for ground.

Product Usage Instructions

1. Before starting the installation process, make sure to shut off
   power at the fuse box or circuit breaker box.
2. Remove the old fixture including the mounting hardware.
3. Take out the new fixture from the packaging and carefully
   unpack it. Lay out all the parts in a clear space.
4. Attach the mounting plate to the junction box using the
   provided mounting screws.
5. Connect the fixture wires to the house wires:
   • Connect the black or smooth fixture wire to the black (hot)
     house wire.
   • Connect the white or ribbed fixture wire to the white (neutral)
     house wire.
   • Connect the bare copper fixture wire to the green (ground)
     house wire.
6. Screw in the ground screw to ensure a secure connection.
7. Attach the fixture to the mounting plate using the provided
   mounting screws. Make sure the fixture is level.
8. Attach the candle cover to the fixture if required.
9. Turn on power at the fuse box or circuit breaker box and test
   the fixture to ensure it is working correctly.

INSTALLATION INSTRUCTIONS
For item#3860-xxx (New. 01/20/2022)
READ AND SAVE THESE INSTRUCTIONS
W ARNI N G ! S HU T PO WE R O F F AT F USE OR CI RC UI T BRE AK E R.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARING FOR INSTALLATION (Fig. 1) 1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts in a
clean area. Take care not to misplace any small parts necessary for installation. ASSEMBLING THE FIXTURE (Fig.1) 3. Determine the desired hanging height and thread rods (F1, F2 and F3) to all thread (I) on the fixture body. Screw loop (H1) to rod (F1). Note: Carefully pass the wires through each rod as you assemble. 4. Attach quick link (G) to loop (H1) and (H2) on the canopy (E). Carefully feed wire through loop (H1), quick link (G), and loop (H2). 5. Position mounting plate (C) on ceiling and mark the location of the two mounting holes. Drill holes in ceiling and insert plastic anchors (A). 6. Attach mounting plate (C) to junction box (not included) using mounting screws (B) (Size: #8-32N*L0.5″). The side of the mounting plate marked “GND” must face out. 7. Secure mounting plate (C) by inserting wood screws (D) through holes on mounting plate and into plastic anchors (A). 8. The support cable is provided to support the weight of the fixture while wiring. Align the fixture to mounting plate (C) and attach hook (P) on the end of support cable (N) into a slot located on mounting plate (C). Carefully allow the support cable (N) to support the weight of the fixture while wiring. CONNECTING THE WIRES (Fig. 2) 9. Connect the electrical wires as shown in figure 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (C) using the green screw provided. 10. Tuck wire connectors neatly into the junction box and raise canopy (E) to ceiling. COMPLETING THE INSTALLATION (Fig. 1) 11. Place canopy (E) over mounting plate (C) and secure with screws (F). 12. Place candle covers (M) over sockets (L). 13. Install (8) eight candelabra base bulbs (K) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. –DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Return power to the junction box and test the fixture.

Fig. 1 Set#A-021-367115
– Mounting plate – Ground screw – Mounting screw*4
A C D N B E F H2 G H1
F1
F2
F3 I

P
K M
L

Rod# W30-1-695*2(F1)/3860-695 Rod# W30-1-66A*2(F1)/3860-726

W30-1-695*4(F2)/3860-695

W30-1-66A*4(F2)/3860-726

W30-H-695*2(F3)/3860-695

W30-H-66A*2(F3)/3860-726

Candle cover#CCV24048P-695

Fig. 2
FIXTURE WIRES Black or Smooth

FIXTURE WIRES White or Ribbed

FIXTURE WIRES Bare Copper (Ground)

Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

HOUSE WIRES Black (Hot)

HOUSE WIRES White (Neutral)

HOUSE WIRES Green (Ground)

Page: 1/1

LA-3514E