Tiramisubest W550xy58044 Nest Swing With Swing Set Stand Instruction Manual

W550XY58044 Nest Swing with Swing Set Stand

Nest Swing With Stand

Stand Assembled Height: 79

Nest Swing Diameter: 43

Maximum User Weight: 150KG (330LB)

Light strip set

1. Lay the nest swing (1) on the floor and open the tabs with the
   Velcro straps.
2. Slide swing tubes (2) into the pockets of nest swing (1) as
   shown below.
3. Place the two swing cords (3) with the suspensions made of
   plastic in the correct sequence next to the nest swing (1). Please
   make sure that the swing cords (3) are not twisted.
4. Slide the plastic suspension of the swing cords (3) from above
   through the opening of the tab with the Velcro straps. Then use
   side II (see marking) to attach the suspension to the thicker
   tube.
5. Now connect the swing tubes (2) to each other, while pressing
   down the spring button on the thinner end of the tube. The
   inter-locking is achieved through the latching and clicking of the
   spring button. Now, close the tab with the Velcro straps.
6. Now, the nest swing seat is assembled as the photo shows.
7. Slide the light strip in the light strip set (18) into the
   pockets of nest swing (1). Control the light strip with the remote
   controller in the light strip set (18).
8. Put the thicker end of bottom frame tube (4) to plastic
   protective sleeve (16) and please make sure they are tightly
   connected. Connect upper frame tube (6) to middle frame tube (5),
   and the connection is achieved with M8 Bolt (8), M8 Spring washer
   (10), and M8 washer (9). Tighten the Connection with L shaped
   wrench (B). Repeat the process on the connection between upper
   frame tube (6) and middle frame tube (5).
9. Connect cruciform tube (7) to the 4 pcs upper frame tubes (6),
   using M8 Bolt (8), M8 Spring washer (10), and M8 washer (9).
   Tighten the Connection with L shaped wrench (B).
10. Attach carabiner (14) and M10 ring bolt (13) to cruciform tube
    (7) with M10 washer (12), M10 spring washer (19), and M10 nut (11).
    Tighten them with M10 wrench (C).
11. Rotate the lock of carabiner (14) until it is open. Hang the
    nest Swing on the stand by putting the ring of swing cords (3) in
    the carabiner (14). Make sure you lock the carabiner (14).
12. Remove part a and b from rope (15). Attach the bolt of rope
    (15) to bottom frame tube (4). Then Tighten connection with part a,
    b, and wrench (A).
13. Put Ceiling (17) on the top of the stand.
14. Congratulations! All Steps are finished. Please check again
    whether all connections are tightened or not. If all tightened
    well, you can enjoy the fun now!

Nest Swing With Stand
Stand Assembled Height:79 Nest Swing Diameter:43 Maximum User Weight:150KG(330LB)

Light strip set

1.Lay the nest swing (1) on the floor and open the tabs with the Velcro straps. 2.Slide swing tubes (2) into the pockets of nest swing (1) as shown below.

4.Place the two swing cords (3) with the suspensions made of plastic in the correct sequence next to the nest swing (1).Please make sure that the swing cords (3) are not twisted.
5.Slide the plastic suspension of the swing cords (3) from above through the opening of the tab with the Velcro straps.Then use side “II” (see marking) to attach the suspension to the thicker tube
6.Now connect the swing tubes (2) to each other,while pressing down the spring button on the thinner end of the tube.The inter-locking is achieved through the latching and clicking of the spring button.Now,close the tab with the Velcro straps.

Now,the nest swing seat is assembled as the photo shows.
7.Slide the light strip in the light strip set (18) into the pockets of nest swing (1) .Control the light strip with the remote controller in the light strip set (18) .
18

8.Put the thicker end of bottom frame tube (4) to plastic protective sleeve (16) and please make sure they are tightenly connected.Connect upper frame tube (6) to middle frame tube (5),and the connection is achieved with M8 Bolt (8) ,M8 Spring washer (10),and M8 washer (9).Tighten the Connection with L shaped wrench (B).Repeat the process on the connection between upper frame tube (6) and middle frame tube (5).
16
9.Connect cruciform tube (7) to the 4 pcs upper frame tubes (6),using M8 Bolt (8), M8 Spring washer (10),and M8 washer (9).Tighten the Connection with L shaped wrench (B).

10.Attach carabiner (14) and M10 ring bolt (13) to cruciform tube (7) with M10 washer (12),M10 spring washer (19) and M10 nut (11). Tighten them with M10 wrench (C).
11.Rotate the lock of carabiner (14) until it is open.Hang the nest Swing on the stand by putting the ring of swing cords (3) in the carabiner (14).Make sure you lock the carabiner (14).

12.Remove part a and b from rope (15). Attach the bolt of rope (15) to bottom frame tube (4).Then Tighten connection with part a,b and wrench (A).
17
13.Put Ceiling (17) on the top of the stand.

14.Congratulations! All Steps are finished. please check again whether All connections are tightened or not.If all tightened well,You Can enjoy the fun now!