Sussex Vbds160rh Voda Bath Mixer Diverter System Dress Kit Installation Guide

VBDS160RH Voda Bath Mixer Diverter System Dress Kit

Product Information:

The Voda Bath Mixer Diverter System Dress Kit is a versatile
plumbing product designed to provide a convenient and efficient way
to control the flow of water in your bath. The product is available
in three different sizes: 160mm, 200mm, and 250mm. It comes with a
mixer dress kit and a diverter dress kit.

The product code for the Voda Bath Mixer Diverter System is CBM.
It is manufactured by Sussex Taps Pty Ltd and complies with AS/NZS
3718:2005 standards. It is water-efficient, with a rating of 5.0
liters per minute.

Product Usage Instructions:

Mixer Dress Kit Installation:

1. Remove the protective cover from the diverter.
2. Fit the dress ring onto the diverter.
3. Attach the handle body to the diverter. Note that the pin
   position of the handle is optional.
4. Secure the handle body by tightening the set screw using the
   provided Allen key.
5. Attach the handle pin. Apply a small amount of silicone or mild
   adhesive (Loctite) to prevent the pin from becoming loose.

Diverter Dress Kit Installation:

6. Apply sealing tape (Teflon) to the male thread of the
   outlet.
7. Place the dress ring and dress flange over the prepared male
   thread.
8. Fit the outlet onto the male thread.

Hand Shower Fit Off:

9. Apply sealing tape (Teflon) to the male thread of the hand
   shower.
10. Place the dress ring over the prepared male thread.
11. Fit the hand shower post onto the male thread.
12. Connect the hand shower hose to the post.

To complete the installation, operate the mixer(s) and check the
flow of both hot and cold water from the outlet. Also, check all
fittings and fixtures for any water leaks.

Rough-In Plumbing:

Prior to installing the Voda Bath Mixer Diverter System,
calculate the finished wall thickness. The maximum wall thickness
should be 30mm. If your wall thickness exceeds this limit, contact
the manufacturer for further options.

14. Prepare a nogging to be fixed parallel between the wall
    studs.
15. The nogging should be positioned to allow the base of the
    Masterfit to be 30-32mm back from the stud face.
16. Using the provided screws, mount the Masterfit to the nogging.
    Ensure it is level and square.

Note: The diverter is of the dial type. Rotate the handle to
direct water flow.

Please ensure that the installation of tapware is done by a
licensed plumber in accordance with AS/NZS 3500:2003 standards. The
recommended working water pressure is 300-500 kpa, and the maximum
water temperature is 65°C.

Voda
Bath mixer diverter system Dress kit

Product code: CBM

1

2

Stud Face
Finished Wall Surface

Handle Pin

Apply Silicone

Set Screw

NOGGING t

80 mm B/Plate

64mm Dress Ring

NOGGING

Apply Silicone

Handle Body

Stud Face Finished
Wall Surface
Backplate

Handle Pin
Set Screw

64mm Dress Ring

Handle Body

3
NOGGING t

Stud Face Finished
Wall Surface Backplate
Dress Ring
Bath Outlet

43

NOGGING Masterfit

Stud Face Finished
Wall Surface Backplate
Dress Ring

Hand Held Shower

Hand Shower Post
Check Valve Hand Shower Hose Connection

sussextaps.com.au

Product code

VBDS160RH VBDS200RH VBDS250RH

Bath mixer diverter system 160mm Bath mixer diverter system 200mm Bath mixer diverter system 250mm

1. Mixer dress kit
– Remove Mixer protective cover. – Using silicone, seal the wall surface around the Mixer and Outlet threads. – Apply a small amount of silicone to the rear of the backplate prior to mounting onto the wall. – After Backplate has been mounted, fit the Mixer Dress Ring. – Fit the handle body onto the Mixer Cartridge Lever ensuring the Handle is fully engaged. – Secure the Handle Body by tightening the Set screw using the Allen Key provided (tighten well). – Attach the Handle Pin. NOTE: Apply a small amount of silicone or mild adhesive (Loctite) to the thread of the Handle Pin to assist in preventing the Pin from becoming loose).
2. Diverter dress kit
– Remove Diverter protective cover. – Fit Dress Ring. – Fit the handle body. NOTE: The Pin position of the Handle is optional. Select as desired (Total movement is 90 degrees). – Secure the Handle Body by tightening the Set screw using the Allen Key provided (tighten well). – Attach the Handle Pin. NOTE: Apply a small amount of silicone or mild adhesive (Loctite) to the thread of the Handle Pin to assist in preventing the Pin from becoming loose).
3. Outlet fit off
– Apply sealing tape (Teflon) to male thread. – Place Dress Ring and Dress Flange over prepared male thread. – Fit the Outlet.

4. Hand shower fit off
– Apply sealing tape (Teflon) to male thread. – Place Dress Ring over prepared male thread. – Fit the Hand shower Post. – Connect the Hand Shower Hose to Post. To complete the installation, operate the Mixer(s) checking the flow of both hot and cold water from Outlet. Check all fittings and fixtures for water leaks.

AS/NZS 3718:2005 LIC. 20081

The more stars the more water efficient
WATER RATING
www.waterrating.gov.au
5.0 litres per minute
In accordance with AS/NZS 6400 Licence No. 0124 Sussex Taps Pty Ltd

Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003 Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.

Voda
Bath mixer diverter system Rough-in

Product code: CBM

1 Vi ew f ro m ab ov e

NOGGING

90

This Side UP

70

Outlet 1

Min. 8mm
Outlet 2

Masterfit Diverter

Mixer

30-32

Stud face

Wall Covering Max. 30mm

Back Plate

Dress Ring

Pipe Connections

Outlet 1

Outlet 2

Diverter

Hot

Mixer

Cold

Handle Body
No te: Th e dive rt er i s of t he d ial ty pe , ro ta te h andl e to d irec t

Product code

VBDS160RH VBDS200RH VBDS250RH

Bath mixer diverter system 160mm Bath mixer diverter system 200mm Bath mixer diverter system 250mm

Rough in plumbing
– Prior to installing, calculate the finished wall thickness, maximum is 30mm thick, contact manufacturer for further options.
– If Wall thickness is greater than 30mm, contact manufacturer for further options. – Prepare a Nogging to be fixed parallel between the Wall Studs. – The Nogging must be fitted to enable the base of the Masterfit to be 30-32mm back from the Stud Face. – The Masterfit will be marked “This side Up” to indicate orientation. – Using the screws (x4) provided, mount the Masterfit to the Nogging. Ensure the Masterfit is level and square.

Pipe connections
– The Hot and Cold ports are marked on the Masterfit. (Mixers have individual Hot/Cold inlet ports). – Flush all water feed lines. All lines must be free from any dirt and debris before connecting to the Masterfit. – Connect Hot and Cold lines to the corresponding 1/2″ BSP ports of the Masterfit. (see Drawing) – Do not remove any factory fitted pressure plugs or Fixings. – Once all water connections are made, check Hot/Cold water flow by operating the Mixer Cartridge. – Check all fittings and fixtures for leaks. – Leave the Mixer(s) in the closed position and replace the Mixer protective cover. – Store the Dress Kit in a safe place until required (see Dress Finishing Guide)

Plumber note
– On-site high pressure line testing must be conducted with the Mixer in the closed position. (STATIC TEST ONLY) – Under no circumstances is the Mixer to be opened when exceeding the maximum stated water pressure. – At the completion of the testing, do not relieve any high pressure by opening the Mixer. – Exposing the internals of the Mixer Cartridge to higher than specified water pressures, will void the
manufacturer’s warranty.

sussextaps.com.au

AS/NZS 3718:2005 LIC. 20081
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003 Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.

References