ED2833 Bluetooth Low Energy or ANT or 802.15.4 Module
Product Information for ED2833
The ED2833 module is a low power data communication system that
installs a radio system approved as a radio station based on the
Radio Law. It complies with the following regulatory
information:
- Japan Regulatory Information – approved with a specific antenna
and has an identifier of ED2833 : 005-103105 - Canada Regulatory Information – complies with Innovation,
Science and Economic Development Canada’s applicable licence-exempt
RSSs and certified as a type of portable device with Innovation,
Science and Economic Development Canada Rules. It also has an RF
Exposure requirement of maintaining a separation distance of
minimum 15 mm between the user and/or bystander and the antenna and
/or radiating element. - FCC Regulatory Information – complies with part 15 of the FCC
Rules and is only authorized for specific rule parts (Part 15
Subpart C) listed on the grant. The host product manufacturer is
responsible for compliance to any other FCC rules that apply to the
host not covered by the modular transmitter grant of certification.
The final host product still requires Part 15 Subpart B compliance
testing with the modular transmitter installed.
Product Usage Instructions for ED2833
To use the ED2833 module, follow these instructions:
- Install the module in the host device according to the
interface specification. - Ensure that your product can bear a label with the regulatory
information specified above. If the product is too small, place it
in the instruction manual and package. - For Canada Regulatory Information, maintain a separation
distance of minimum 15 mm between the user and/or bystander and the
antenna and /or radiating element to maintain compliance with RF
Exposure requirement. - For FCC Regulatory Information, ensure that the final host
product still requires Part 15 Subpart B compliance testing with
the modular transmitter installed. - Do not make any changes or modifications not expressly approved
by the party responsible for compliance as it could void the user’s
authority to operate the equipment.
ED2833
23-Jan.2023 Ver.0.1 KAGA FEI Co., Ltd.
User manual
(for ED2833)
FCC ID: 2A6NFED2833 IC: 28568-ED2833
KAGA FEI Co., Ltd.
1/5
ED2833
23-Jan.2023 Ver.0.1 KAGA FEI Co., Ltd.
This module should be installed in the host device according to the interface specification .
1) Japan Regulatory Information a) This module is approved with the specific antenna on this module. b) Please ensure that your product can bear a label with the following information. If the product is so small that it is not practicable to place the label, please place it in the instruction manual and package. This product installs a radio system which has been approved as a radio station in a low power data communication system based on the Radio Law. ED2833 : 005-103105
2) Canada Regulatory Information The following information must be indicated on the host device of this module; a) This device complies with Innovation, Science and Economic Development Canada’s applicable licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’ Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) l’appareil ne doit pas produire de brouillage; 2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
b) This product is certified as type of the portable device with Innovation, Science and Economic Development Canada Rules. To maintain compliance with RF Exposure requirement, please use within specification of this product and have a separation distance of minimum 15 mm between the user and/or bystander and the antenna and /or radiating element. This distance ensures that the output power (e.i.r.p.) of ED2833 is below the SAR evaluation Exemption limits defined in RSS-102 issue 5.
Ce produit est certifié comme type de l’appareil portable avec Règles de Innovation, Sciences et Développement économique Canada. Pour maintenir l’acquiescement avec exigence Exposition de RF, veuillez utiliser dans spécification de ce produit et respecter une distance de séparation d’au moins 15 mm entre l’utilisateur et / ou un tiers et l’antenne et / ou l’élément rayonnant. Cette distance garantit que la puissance de sortie (p.i.r.e.) d’ED2833 est inférieure aux limites d’exemption de l’évaluation SAR définies dans le numéro 5 de la norme RSS-102. – IC: 28568-ED2833
KAGA FEI Co., Ltd.
2/5
ED2833
23-Jan.2023 Ver.0.1 KAGA FEI Co., Ltd.
c) Please notify certified ID by either one of the following method on your product. -Contains IC : 28568-ED2833 Specifiez ID certifiée dans votre produit par une de méthode suivante. -Contains IC : 28568-ED2833
3) FCC Regulatory Information
a) This device complies with part 15 of the FCC Rules.
-Part 15 Subpart C
b) The following statement shall be indicated on the host device or the user manual of the
host device; Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
c) Please notify certified ID by either one of the following method on your product.
-Contains Transmitter Module FCC ID: 2A6NFED2833
-Contains FCC ID: 2A6NFED2833
d) The following statement shall be indicated in the user manual of the host device;
CAUTION: Changes or modifications not expressly approved by the party responsible
for compliance could void the use’s authority to operate the equipment.
e) The modular transmitter is only FCC authorized for the specific rule parts (Part 15
Subpart C) listed on the grant, and the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the modular
transmitter grant of certification. The final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.
f) This product is certified as type of the portable device with FCC Rules. To maintain
compliance with RF Exposure requirement, please use within specification of this
product.
g) The following statement shall be indicated in the user manual of the host device; The
antenna used for this transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
h) This module can change the output power depending on the circumstances by the
application software which is developed by module installer. Any end user cannot
change the output power.
i) Antenna List
No.1
Antenna Category Monopole
Antenna Type
PCB antenna
Dimensions
8.6mm x 7.5mm
4) CE Regulatory Information a) When your end product installs this module, it is required to proceed additional certification processes before placing on the market in EU member states to make your products fully comply with relative EU standards. b) KAGA FEI can provide you the test reports of conducted measurement portion for the radio module. You can utilize the test reports for the certification processes of your end product as it requires radio testing.
KAGA FEI Co., Ltd.
3/5
ED2833
Control No.
Pin Descriptions
Control name (1/2) Pin Layout
23-Jan.2023 Ver.0.1 KAGA FEI Co., Ltd.
Pin
Pin name
Pin function
Description
1
GND (Corner pad)
Power
Ground 0.55mm x 0.8mm
2
VBUS
Power
5 V input for USB 3.3 V regulator
3
D-
USB
USB D-
4
D+
USB
USB D+
5
P0.07
Digital I/O
General purpose I/O, Trace buffer clock
6
P0.08
Digital I/O
General purpose I/O
7
GND
Power
Ground
8
P0.01/XL2
Digital I/O Analog input
General purpose I/O Connection for 32.768 kHz crystal
9
P0.00/XL1
Digital I/O Analog input
General purpose I/O Connection for 32.768 kHz crystal
10
P0.04_AIN2
Digital I/O Analog input
General purpose I/O Analog input
11
GND (Corner pad)
Power
Ground 0.55mm x 0.8mm
12
P0.26
Digital I/O
General purpose I/O
13
GND
Power
Ground
14
OUT_MOD
RF In/Out
RF I/O pin. It should be connected to Pin15 OUT_ANT for normal operation.
15
OUT_ANT
Antenna In/Out
Internal antenna. It should be connected to Pin14 OUT_MOD for normal operation
16
GND (Corner pad)
Power
Ground 0.55mm x 0.8mm
17
GND (Corner pad)
Power
Ground 0.55mm x 0.8mm
18
P0.10_NFC2
Digital I/O NFC input
General purpose I/O NFC antenna connection
19
SWDIO
Debug
Serial wire debug I/O for debug and programming
20
VDD
Power
Power supply
21
VDDH
Power
High voltage power supply
22
DECUSB
Power
USB 3.3V regulator supply decoupling
KAGA FEI Co., Ltd.
4/5
ED2833
Control No.
Control name (2/2) Pin Layout
23-Jan.2023 Ver.0.1 KAGA FEI Co., Ltd.
Pin
Pin name
Pin function
Description
23
P0.15
Digital I/O
General purpose I/O
24
P0.05_AIN3
Digital I/O Analog input
General purpose I/O Analog input
25
P0.06
Digital I/O
General purpose I/O
26
P0.30_AIN6
Digital I/O Analog input
General purpose I/O Analog input
27
P0.27
Digital I/O
General purpose I/O
28
P0.28_AIN4
Digital I/O Analog input
General purpose I/O Analog input
29
P0.31_AIN7
Digital I/O Analog input
General purpose I/O Analog input
30
P0.02_AIN0
Digital I/O Analog input
General purpose I/O Analog input
31
P0.03_AIN1
Digital I/O Analog input
General purpose I/O Analog input
32
P0.29_AIN5
Digital I/O Analog input
General purpose I/O Analog input
33
P0.09_NFC1
Digital I/O NFC input
General purpose I/O NFC antenna connection
34
P0.18_RESET
Digital I/O
General purpose I/O Configurable as pin RESET
35
SWDCLK
Debug
Serial wire debug clock input for debug and programming
36
GND (Center pad)
Power
Ground 2.8mm x 1.5 mm
37
NC (Corner pad)
NC
NC 0.55mm x 0.8mm
38
NC (Corner pad)
NC
NC 0.55mm x 0.8mm
KAGA FEI Co., Ltd.
5/5
