TOB 4356 Ace Flush Mount
Product Information
Product Name: Ace 12 Flush Mount
Item Number: TOB 4356
Installation Requirements: This light fixture should be
installed in accordance with all applicable, local installation
codes, and by a person familiar with the construction and operation
of it, as well as the hazards involved.
Assembly Instructions
- Carefully remove all parts from the box. Place on a clean, soft
surface. - Remove the fixture body (D) from the mounting plate (A) by
unscrewing. - Remove the mounting plate (A) from the light source (J) by
removing threaded caps (E). - Using the mounting plate (A) as a guide, line it up with the
junction box and mark anchor positions. - Using a drill bit slightly smaller than the anchor, drill holes
in the marked positions. Install anchors (L) into the holes using a
hammer. - Install the mounting plate (A) to the junction box and secure
it with mounting screws (B), then secure wood screws (K) to anchors
(L). - Remove the quick connector (I) from the light source.
- Wrap the quick connector ground wire (bare copper) around the
green grounding screw as shown in diagram 1. Tighten it. Continue
the quick connector ground wire and connect it to the supply ground
wire (usually green or bare copper) using a wire nut (C). Note: It
is imperative that the fixture is grounded. - Connect the quick connector neutral wire (white) to the supply
neutral wire (usually white) using a wire nut (C). - Connect the quick connector hot wire (black) to the supply hot
wire (usually black) using a wire nut (C). Caution: Do not reverse
the hot and neutral connections. - Make sure all wire connections are tight, then carefully tuck
them into the junction box. - Connect the quick connectors (I & H) together as shown in
diagram 2, then install the light source (J) to the threaded nipple
(G) and secure it with threaded caps (E). - Loosen thumbscrews (N) from the shade bracket, then install the
glass shade (F) to the fixture body (D) and secure it with
thumbscrews (N). Note: Do not over-tighten, otherwise, the shade
could become damaged. - Run the support cable through the hole on the bracket (M).
Loosen the cable lock and install it at the end of the support
cable. Insert the other end of the cable through the cable lock and
tighten both ends with a screwdriver to secure it. Refer to diagram
3 & 4 for guidance. - Align the studs (N) on the mounting plate (A) with the slots on
the fixture body (D), then turn clockwise until locked in place.
See diagram 5 for reference.
Care Instructions: Clean only with a soft dry
cloth or feather duster. Do not use abrasive or chemical
agents.
ASSEMBLY INSTRUCTIONS
C A
Diagram 1 B
L M
G K
J E
D N
F
Ace 12″ Flush Mount
Item # TOB 4356
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Drill
Pencil
Hammer
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove fixture body (D) from mounting plate (A) by unscrewing. 3. Remove mounting plate (A) from light source (J) by removing threaded
caps (E). 4. Using mounting plate (A) as a guide, line up with the junction box and
mark anchor positions. 5. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (L) into the holes using hammer. 6. Install mounting plate (A) to the junction box and secure with
mounting screws (B), then secure wood screws (K) to anchors (L). 7. Remove quick connector (I) from light source. 8. Wrap quick connector ground wire (bare copper) around the green
grounding screw (see diagram 1). Tighten. Continue quick connector ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (C). NOTE: It is imperative that the fixture is grounded. 9. Connect quick connector neutral wire (white) to the supply neutral wire (usually white) using wire nut (C). 10. Connect quick connector hot wire (black) to the supply hot wire (usually black) using wire nut (C). CAUTION: Do not reverse the hot and neutral connections.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
C A O
B Diagram 5
I H
Diagram 2
L
M G K
M Diagram 3
Diagram 4 J E
D N
Ace 12″ Flush Mount
Item # TOB 4356
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
11. Make sure all wire connections are tight, then carefully tuck into the junction box.
12. Connect quick connectors (I & H) together (see diagram 2), then install light source (J) to threaded nipple (G) and secure with threaded caps (E).
13. Loosen thumbscrews (N) from shade bracket, then install glass shade (F) to fixture body (D) and secure with thumbscrews (N). NOTE: Do not over-tighten otherwise shade could become damaged.
14. Run support cable through hole on bracket (M). Loosen cable lock and install to end of support cable. Insert other end of cable through the cable lock and tighten ends with a screwdriver to secure. (see diagram 3 &4)
15. Align studs (N) on mounting plate (A) with slots on fixture body (D), then turn clockwise until locked in place. See diagram 5.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
F
M
LI ST ED
US
