TOB5645-6 Junio 6-Light Pendant
Product Information
Product Name: Junio 6-Light Pendant
Item Number: TOB5645-6
Product Description: The Junio 6-Light Pendant
is a stylish and modern lighting fixture that adds a touch of
elegance to any space. It features six lights and comes with a
mounting plate, canopy, and all necessary wires and connectors for
installation. Please note that the cord mount is sold separately
and bulbs are not included.
Product Usage Instructions
- Carefully remove all parts from the box and place them on a
clean, soft surface. - Remove the mounting plate (B) from the canopy (J) by removing
screws (C). - Remove the metal plate (H) from the mounting plate (B) by
removing collar rings (O). - Using the mounting plate (B) as a guide, line it up with the
junction box and mark the anchor positions. - Using a drill bit slightly smaller than the anchor, drill holes
in the marked positions. Install anchors (A) into the holes using a
hammer. - Install the mounting plate (B) to the junction box and secure
it with mounting screws (G). Then, secure wood screws (F) to the
anchors (A). - Feed the fixture wires through the canopy (J), collar rings
(O), and metal plate (H). Note: Slide packaging up the cord for
light head inspection, then slide it back down and leave it in
place until installation is complete. Refer to diagram 1. - Insert the fixture wires through the center hole of the
mounting bracket and secure them with set screws (D) using the
provided wrench (K). Refer to diagram 2. Note: Set the fixture to
the desired height before moving to the next step. - Cut excess wires, leaving enough length to reach the junction
box. Separate the wires and strip insulation on each end. - Wrap the supply ground wire (bare copper) around the green
grounding screw and tighten it. Connect two jumper wires to the
supply ground wire (usually green or bare copper) and secure them
using a wire nut (E). Divide the fixture ground wires (green) by
section and connect them to the jumper ground wires, securing them
with a wire nut (E). Refer to diagram 3. Note: Divide sections of
ground wire evenly to jumper wires as shown in diagram 3. It is
imperative that the fixture is grounded. - Connect two jumper neutral wires to the supply neutral wire
(usually white) and secure them using a wire nut (E). Divide the
fixture neutral wires (white) by section and connect them to the
jumper neutral wires, securing them with a wire nut (E). Refer to
diagram 3. Note: Divide sections of neutral wire evenly to jumper
wires as shown in diagram 3.
ASSEMBLY INSTRUCTIONS
Cord mount sold separately
Diagram 1 L M
Bulbs not included N
A
E
B
D F
H G
O J C
D
K
Diagram 2
Junio 6-Light Pendant
Item # TOB5645-6
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Wire Strippers Drill
Hammer
Wire Cutters Pencil
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove mounting plate (B) from canopy (J) by removing screws (C). 3. Remove metal plate (H) from mounting plate (B) by removing collar
rings (O). 4. Using mounting plate (B) as a guide, line up with the junction box
and mark anchor positions. 5. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (A) into holes using hammer. 6. Install mounting plate (B) to junction box and secure with mounting
screws (G), then secure wood screws (F) to anchors (A). 7. Feed fixture wires through canopy (J), collar rings (O) and metal
plate (H). NOTE: Slide packaging up cord for light head inspection, then slide back down and leave in place until installation is complete. See diagram 1. 8. Insert fixture wires through the center hole of mounting bracket and secure with set screws (D) using provided wrench (K). See diagram 2. NOTE: Set fixture to desired height before moving to next step. 9. Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8″.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Cord mount sold separately
L M Bulbs not included N
A
E
B
D F
H G
O
J C
Supply neutral wire
Jumper neutral wires
Supply hot wire
Supply ground wire
Jumper hot wires
Fixture neutral wires
Jumper ground wires
Fixture hot wires
Fixture ground wire
Diagram 3
Junio 6-Light Pendant
Item # TOB5645-6
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
10. Wrap supply ground wire (bare copper) around the green grounding screw. Tighten. Connect 2 jumper wires to supply ground wire (usually green or bare copper) and secure using wire nut (E). Divide fixture ground wires (green) by section and connect to jumper ground wires, securing with wire nut (E). See diagram 3. NOTE: Divide sections of ground wire evenly to jumper wires as shown in diagram 3 NOTE: It is imperative that the fixture is grounded.
11. Connect 2 jumper neutral wires to supply neutral wire (usually white) and secure using wire nut (E). Divide fixture neutral wires (white) by section and connect to jumper neutral wires, securing with wire nut (E). See diagram 3. NOTE: Divide sections of neutral wire evenly to jumper wires as shown in diagram 3.
12. Connect 2 jumper hot wires to supply hot wire (usually black) and secure using wire nut (E). Divide fixture hot wires (black) by section and connect to jumper hot wires, securing with wire nut (E). See diagram 3. NOTE: Divide sections of hot wire evenly to jumper wires as shown in diagram 3. CAUTION: Do not reverse the hot and neutral connections.
13. Install metal plate (H) to mounting plate (B) and secure with collar rings (O).
14. Install canopy (J) to mounting plate (B) and secure with screws (C). 15. Install light bulbs into the sockets.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Cord mount sold separately
L M Bulbs not included N
A
E
B
D F
H G
O
J C
Supply neutral wire
Jumper neutral wires
Supply hot wire
Supply ground wire
Jumper hot wires
Fixture neutral wires
Jumper ground wires
Fixture hot wires
Fixture ground wire
Diagram 3
Junio 6-Light Pendant Item # TOB5645-6
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
16. Install glass shades (N) to fixture body (L) and secure with thumbscrews (M). NOTE: Thread thumbscrews (M) in evenly to ensure glass is properly secured. Do not overtighten.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
A B C
Assembled View
F
G D E
Junio Cord Mount Item # TOB5645-PRT
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
CORD MOUNT OPTION (SOLD SEPARATELY) 1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove canopy (F) from mounting plate (B) by unscrewing, then
remove threaded cap (E) and wire mounts (G & D) from mounting plate. 3. Using the mounting plate (B) as a guide, line up with ceiling and mark anchor positions. 4. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into the holes using hammer. 5. Install mounting plate (B) to ceiling and secure with wood screws (C) to anchors (A). 6. Thread canopy (F) to mounting plate (B). 7. Place fixture wire into slot of bottom wire mount (D). 8. Adjust fixture wire to desired height, then install wire mounts (G & D) to mounting plate (B) and secure with threaded cap (E).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
