TOB5645-3 Junio 3-Light Pendant
Product Information
Product Name: Junio 3-Light Pendant
Item Number: TOB5645-3
Bulbs: Not included
Product Usage Instructions
- Carefully remove all parts from the box and place them on a
clean, soft surface. - Remove the mounting plate (B) from the canopy (J) by removing
screws (C). - Remove the metal plate (H) from the mounting plate (B) by
removing collar rings (O). - Using the mounting plate (B) as a guide, line it up with the
junction box and mark the anchor positions. - Using a drill bit slightly smaller than the anchor, drill holes
in the marked positions. Install anchors (A) into the holes using a
hammer. - Install the mounting plate (B) to the junction box and secure
it with mounting screws (G). Then, secure wood screws (F) to the
anchors (A). - Feed the fixture wires through the canopy (J), collar rings
(O), and metal plate (H). Slide the packaging up the cord for light
head inspection, then slide it back down and leave it in place
until installation is complete. Refer to diagram 1. - Insert the fixture wires through the center hole of the
mounting bracket and secure them with set screws (D) using the
provided wrench (K). Refer to diagram 2. Note: Set the fixture to
the desired height before moving to the next step. - Cut excess wires, ensuring enough length to reach the junction
box. Separate the wires and strip insulation on each end. - Wrap the supply ground wire (bare copper) around the green
grounding screw and tighten it. Continue with the fixture ground
wire and connect it to the supply ground wire (usually green or
bare copper) using a wire nut (A). Note: It is imperative that the
fixture is grounded. - Connect the fixture neutral wire (white) to the supply neutral
wire (usually white) using a wire nut (A). - Connect the fixture hot wire (black) to the supply hot wire
(usually black) using a wire nut (A). Caution: Do not reverse the
hot and neutral connections. - Install the metal plate (H) to the mounting plate (B) and
secure it with collar rings (O). - Install the canopy (J) to the mounting plate (B) and secure it
with screws (C). - Install light bulbs into the sockets.
- Install glass shades (N) to the fixture body (L) and secure
them with thumbscrews (M). Note: Thread thumbscrews (M) evenly to
ensure proper glass security. Do not overtighten.
ASSEMBLY INSTRUCTIONS
Cord mount sold separately
A E
G
L M Bulbs not included N
B
F D H
O
Diagram 1
J C
DK Diagram 2
Junio 3-Light Pendant
Item # TOB5645-3
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Wire Strippers Drill
Hammer
Wire Cutters Pencil
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove mounting plate (B) from canopy (J) by removing screws (C). 3. Remove metal plate (H) from mounting plate (B) by removing collar
rings (O). 4. Using mounting plate (B) as a guide, line up with the junction box
and mark anchor positions. 5. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (A) into holes using hammer. 6. Install mounting plate (B) to junction box and secure with mounting
screws (G), then secure wood screws (F) to anchors (A). 7. Feed fixture wires through canopy (J), collar rings (O) and metal
plate (H). NOTE: Slide packaging up cord for light head inspection, then slide back down and leave in place until installation is complete. See diagram 1. 8. Insert fixture wires through the center hole of mounting bracket and secure with set screws (D) using provided wrench (K). See diagram 2. NOTE: Set fixture to desired height before moving to next step. 9. Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8″.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Cord mount sold separately
A E
G
L M Bulbs not included N
B
F D H
O
Diagram 1
J C
DK Diagram 2
Junio 3-Light Pendant Item # TOB5645-3
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
10. Wrap supply ground wire (bare copper) around the green grounding screw. Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A). NOTE: It is imperative that the fixture is grounded.
11. Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
12. Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
13. Install metal plate (H) to mounting plate (B) and secure with collar rings (O).
14. Install canopy (J) to mounting plate (B) and secure with screws (C). 15. Install light bulbs into the sockets. 16. Install glass shades (N) to fixture body (L) and secure with
thumbscrews (M). NOTE: Thread thumbscrews (M) in evenly to ensure glass is properly secured. Do not overtighten.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
A B C
Assembled View
F
G D E
Junio Cord Mount Item # TOB5645-PRT
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
CORD MOUNT OPTION (SOLD SEPARATELY) 1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove canopy (F) from mounting plate (B) by unscrewing, then
remove threaded cap (E) and wire mounts (G & D) from mounting plate. 3. Using the mounting plate (B) as a guide, line up with ceiling and mark anchor positions. 4. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into the holes using hammer. 5. Install mounting plate (B) to ceiling and secure with wood screws (C) to anchors (A). 6. Thread canopy (F) to mounting plate (B). 7. Place fixture wire into slot of bottom wire mount (D). 8. Adjust fixture wire to desired height, then install wire mounts (G & D) to mounting plate (B) and secure with threaded cap (E).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
