TOB5645-5 Junio 5-Light Pendant
Product Information
Product Name: Junio 5-Light Pendant
Item Number: TOB5645-5
Description: The Junio 5-Light Pendant is a
light fixture that requires assembly and installation. It should be
installed in accordance with all applicable local installation
codes and by a person familiar with the construction and operation
of the fixture, as well as the hazards involved. Bulbs are not
included with the product. It is important to inspect the item and
its contents carefully before installation.
Assembly Instructions
- Carefully remove all parts from the box and place them on a
clean, soft surface. - Remove the mounting plate (B) from the canopy (J) by unscrewing
the screws (C). - Remove the metal plate (H) from the mounting plate (B) by
removing the collar rings (O). - Using the mounting plate (B) as a guide, align it with the
junction box and mark the anchor positions. - Using a drill bit slightly smaller than the anchor, drill holes
in the marked positions and install anchors (A) into the holes
using a hammer. - Install the mounting plate (B) to the junction box and secure
it with the mounting screws (G). Then, secure the wood screws (F)
to the anchors (A). - Feed the fixture wires through the canopy (J), collar rings
(O), and metal plate (H). Note that you should slide the packaging
up the cord for light head inspection, then slide it back down and
leave it in place until installation is complete. - Insert the fixture wires through the center hole of the
mounting bracket and secure them with the set screws (D) using the
provided wrench (K). - Set the fixture to the desired height before moving to the next
step. Cut excess wires, leaving enough to reach the junction box.
Separate the wires and strip insulation on each wire by 5/8
inch. - Wrap the supply ground wire (bare copper) around the green
grounding screw and tighten it. Connect two jumper wires to the
supply ground wire and secure them using a wire nut (E). Divide the
fixture ground wires by section and connect them to the jumper
ground wires, securing them with a wire nut (E). - Connect two jumper neutral wires to the supply neutral wire
(usually white) and secure them using a wire nut (E). Divide the
fixture neutral wires by section and connect them to the jumper
neutral wires, securing them with a wire nut (E).
Note: It is imperative that the fixture is properly grounded and
all steps are followed according to the provided diagrams.
ASSEMBLY INSTRUCTIONS
Cord mount sold separately
Diagram 1 L M
Bulbs not included N
A E
C
B F D
G H O
J
D
K
Diagram 2
Junio 5-Light Pendant
Item # TOB5645-5
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Wire Strippers Drill
Hammer
Wire Cutters Pencil
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove mounting plate (B) from canopy (J) by removing screws (C). 3. Remove metal plate (H) from mounting plate (B) by removing collar
rings (O). 4. Using mounting plate (B) as a guide, line up with the junction box
and mark anchor positions. 5. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (A) into holes using hammer. 6. Install mounting plate (B) to junction box and secure with mounting
screws (G), then secure wood screws (F) to anchors (A). 7. Feed fixture wires through canopy (J), collar rings (O) and metal
plate (H). NOTE: Slide packaging up cord for light head inspection, then slide back down and leave in place until installation is complete. See diagram 1. 8. Insert fixture wires through the center hole of mounting bracket and secure with set screws (D) using provided wrench (K). See diagram 2. NOTE: Set fixture to desired height before moving to next step. 9. Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8″.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Cord mount sold separately
L M Bulbs not included
N
A E
C
B F D
G H O
J
Supply neutral wire
Supply hot wire
Supply ground wire
Jumper neutral wires
Fixture neutral wires
Jumper hot wires
Jumper ground wires
Fixture hot wires
Fixture ground wire
Diagram 3
Junio 5-Light Pendant
Item # TOB5645-5
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
10. Wrap supply ground wire (bare copper) around the green grounding screw. Tighten. Connect 2 jumper wires to supply ground wire (usually green or bare copper) and secure using wire nut (E). Divide fixture ground wires (green) by section and connect to jumper ground wires, securing with wire nut (E). See diagram 3. NOTE: Divide sections of ground wire evenly to jumper wires as shown in diagram 3 NOTE: It is imperative that the fixture is grounded.
11. Connect 2 jumper neutral wires to supply neutral wire (usually white) and secure using wire nut (E). Divide fixture neutral wires (white) by section and connect to jumper neutral wires, securing with wire nut (E). See diagram 3. NOTE: Divide sections of neutral wire evenly to jumper wires as shown in diagram 3.
12. Connect 2 jumper hot wires to supply hot wire (usually black) and secure using wire nut (E). Divide fixture hot wires (black) by section and connect to jumper hot wires, securing with wire nut (E). See diagram 3. NOTE: Divide sections of hot wire evenly to jumper wires as shown in diagram 3. CAUTION: Do not reverse the hot and neutral connections.
13. Install metal plate (H) to mounting plate (B) and secure with collar rings (O).
14. Install canopy (J) to mounting plate (B) and secure with screws (C). 15. Install light bulbs into the sockets.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Cord mount sold separately
L M Bulbs not included
N
A E
C
B F D
G H O
J
Supply neutral wire
Supply hot wire
Supply ground wire
Jumper neutral wires
Fixture neutral wires
Jumper hot wires
Jumper ground wires
Fixture hot wires
Fixture ground wire
Diagram 3
Junio 5-Light Pendant Item # TOB5645-5
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
16. Install glass shades (N) to fixture body (L) and secure with thumbscrews (M). NOTE: Thread thumbscrews (M) in evenly to ensure glass is properly secured. Do not overtighten.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
A B C
Assembled View
F
G D E
Junio Cord Mount Item # TOB5645-PRT
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
CORD MOUNT OPTION (SOLD SEPARATELY) 1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove canopy (F) from mounting plate (B) by unscrewing, then
remove threaded cap (E) and wire mounts (G & D) from mounting plate. 3. Using the mounting plate (B) as a guide, line up with ceiling and mark anchor positions. 4. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into the holes using hammer. 5. Install mounting plate (B) to ceiling and secure with wood screws (C) to anchors (A). 6. Thread canopy (F) to mounting plate (B). 7. Place fixture wire into slot of bottom wire mount (D). 8. Adjust fixture wire to desired height, then install wire mounts (G & D) to mounting plate (B) and secure with threaded cap (E).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
