61640 Salvo Wall Light
Product Information
This product is a wall light called Salvo Wall, manufactured by
Saxby Lighting. It operates on a voltage of 220-240V~ with a
frequency of 50Hz. The light uses two GU10 bulbs with a maximum
wattage of 20W. It has an IP rating of 20, indicating its level of
protection against solid objects and water.
Product Usage Instructions
- Commissioning: Before using the light, ensure it is
properly installed and connected to the power supply. - Fitting/Replacing Bulbs:
- When changing a bulb, always switch off the power at the mains
and allow the bulb to cool before handling. - Dispose of used bulbs carefully.
- Do not exceed the maximum wattage of 20W or use a different
shape bulb than indicated on the fitting. - To access the bulb, remove the wire clip shown in the diagram
provided. Set it aside for refitting later. - Gently remove the old bulb by twisting and pulling it out.
- Fit the new bulb and secure it in place by refitting the wire
clip.
- We recommend cleaning the light with a soft dry cloth.
- Avoid using solvents or abrasive cleaners as they may damage
the finish.
- Waste electrical products should not be disposed of with
household waste. - Please recycle the product where facilities exist.
- Check with your Local Authority or retailer for recycling
advice.
- Always switch off the power supply before changing lightbulbs
or cleaning the light.
Commissioning
light is now ready for use.
Fitting/replacing bulbs – Max. 20W GU10
When changing a bulb, always switch off at the mains and allow the bulb to cool before handling. Dispose of used bulbs carefully. Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting. o access the bulb, remove the wire clip shown in the diagram overleaf. Set aside for refitting later.
in place.
Max. 20W GU10
and pulling out. Fit the new bulb, and secure in place by refitting the wire clip.
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
Recycling advice
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Safety information
For your safety, always switch off the power supply before changing lightbulbs, or cleaning.
Instruction leaflet
Salvo Wall
61640
UK Manufacturer: BH17 7BY EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
www.saxbylighting.com
V3 10/05/2022 Saxby Lighting
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This product is Class 2 (Double insulated) and must not be earthed. Please read these instructions carefully before commencing any work.
electrician. Install in accordance with IEE Wiring regulations and
cannot be serviced. If damage occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt,
If replacing an existing fitting, make a careful note of the connections.
Specification
Voltage: Lamp: IP rating:
220-240V~ 50Hz 2 x Max. 20W GU10 20
Layout
conduit or plastic trunking. sectional area of 1.0mm²
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.
product to separate the bracket from the product
the mounting holes. fixings).
Wiring
Having correctly identified the wiring from your light fitting, connect to the approved outdoor rated external
SUPPLY NEUTRAL SWITCHED LIVE
Check that…
terminal block in the following way:
LIGHT FITTING BLUE (N)
BROWN (L)
No loose strands have been left out of the connection block.
Saxby Lighting - Commercial and Domestic Lighting Supplier
