HL1400 Planetary Floor Mixer
LEGACY+ INSTALLATION GUIDE for Large Floor Model Mixers: HL600,
HL662, HL800 and HL1400
Food Preparation
The following are the instructions to install and use the
mixer:
VERIFY DATA PLATE
Before installation, test the electrical service to ensure that
it matches the specifications on the mixer data plate.DATA PLATE: Refer to the mixer data plate for
specifications.PLACE AND LEVEL THE MIXER
Place the mixer in its operating location. Once in position, the
mixer must be leveled:- Remove the two top cover screws and the top cover.
- Place a level on the top rim of the large pulley.
- Slide shims under the base contact surface of the mixer as
required to level it front-to-back and side-to-side. 80 and 140 qt
mixers may also be bolted to the floor using studs. Refer to the
mixer’s instruction manual for steps.
MAKE ELECTRICAL CONNECTIONS
A hole for 3/4 trade-size conduit is located at the top of the
pedestal. Make electrical connections per the wiring diagram
located on the inside of the top cover. Electrical and grounding
connections must comply with the applicable portion of the National
Electrical Code and/or other local electrical codes. Disconnect the
electrical power to the mixer and follow lockout/tagout
procedures.CHECK OIL LEVEL
The mixer is shipped with oil in the transmission. Check oil
level before starting the mixer. If the oil level is below the line
on the oil dipstick, add a small amount of transmission oil until
it returns to the proper level. Contact your local Hobart Service
Office for the recommended transmission oil.CHECK LUBRICATION
Check the lubrication of the following:
- Planetary seal
- Slideways
- Agitator shaft
WIRING CHECK
Turn the SPEED dial pointer to STIR. Apply power to the mixer
and run the machine for a few minutes. Also check that the bowl
lift raises and lowers.WASH MIXER, BOWLS, AND AGITATORS
Wipe down the mixer with a clean, damp cloth. New mixer bowls
and agitators should be thoroughly washed with hot water and a mild
soap solution, rinsed with either a mild soda or vinegar solution,
and thoroughly rinsed with clear water before being used.
Always refer to procedures as instructed in the Operation Manual
for your specific model. Use care when operating, cleaning or
performing maintenance. For additional product resources, please
visit www.hobartcorp.com.
Food Preparation
LEGACY+ INSTALLATION GUIDE
For Large Floor Model Mixers: HL600, HL662, HL800 and HL1400
1 VERIFY DATA PLATE
Prior to installation, test the electrical service to ensure that it matches the specifications on the mixer data plate.
DATA PLATE
4 CHECK OIL LEVEL
The mixer is shipped with oil in the transmission. Check oil level before starting the mixer. If the oil level is below the line on the oil dipstick, add a small amount of transmission oil until it returns to the proper level. Contact your local Hobart Service Office for the recommended transmission oil.
5 CHECK LUBRICATION
Slideways To reach these areas, fully lower the bowl support and remove the apron, which is secured by two thumb screws. Wipe a thin coat of Lubriplate 630AA on the bowl pad area of the bowl supports and on each slideway. Planetary seal Work a small amount of mineral oil under the lip of the seal. Agitator shaft Apply a thin coat of mineral oil.
PLANETARY SEAL
SLIDEWAYS
2 PLACE AND LEVEL THE MIXER
Place the mixer in its operating location. Once in position, the mixer must be leveled:
1. Remove the two top cover screws and the top cover. 2. Place a level on the top rim of the large pulley. Slide
shims under the base contact surface of the mixer as required to level it front-to-back and side-to-side. 80 and 140 qt mixers may also be bolted to the floor using studs. Refer to the mixer’s instruction manual for steps.
3 MAKE ELECTRICAL CONNECTIONS
A hole for 3/4″ trade-size conduit is located at the top of the pedestal. Make electrical connections per the wiring diagram located on the inside of the top cover. Electrical and grounding connections must comply with the applicable portion of the National Electrical Code and/or other local electrical codes. Disconnect the electrical power to the mixer and follow lockout/tagout procedures.
AGITATOR SHAFT
6 WIRING CHECK
Turn the SPEED dial pointer to STIR. Apply power to the mixer and run the machine for a few minutes. Also check that the bowl lift raises and lowers.
7 WASH MIXER, BOWLS, AND AGITATORS
Wipe down the mixer with a clean, damp cloth. New mixer bowls and agitators should be thoroughly washed with hot water and a mild soap solution, rinsed with either a mild soda or vinegar solution, and thoroughly rinsed with clear water before being used.
Always refer to procedures as instructed in the Operation Manual for your specific model. Use care when operating, cleaning or performing maintenance. For additional product resources, please visit www.hobartcorp.com.
F48687 (02-22) ©2022 Hobart
Premier Foodservice Equipment | Hobart
