Flash-butrym F7100770 Moving Head Led 150w Spot User Manual (+ PDF)

Contents hide

1 F7100770 Moving Head LED 150W Spot

2 Product Information:

3 Product Usage Instructions:

4 Documents / Resources

4.1 References

F7100770 Moving Head LED 150W Spot

Product Information:

Product Name: MOVING HEAD LED 150W SPOT
Version: 0523
Model Number: F7100770
Light Source: Ultra bright 150W LED
PAN Range: 540°
TILT Range: 270°
Color Wheel: 8 main colors + open with the rainbow
Effects: 2 Gobos wheels – Fixed gobo wheel and rotating Gobo
wheel. 7 Gobos + White with Bi-directional rotate effect

Product Usage Instructions:

Unpack and check carefully for any damage or malfunction before
using the fixture. If there is any transportation damage, please
contact the nearest authorized technical assistance center.
Ensure that the voltage and frequency of the power supply match
the power requirements of the fixture.
Ground the yellow/green conductor to earth to avoid electric
shock.
Disconnect the main power before servicing and
maintenance.
Use a safety chain when fixing this fixture.
Do not touch any wire during operation to prevent electric
shock.
Do not connect the device to any dimmer pack.
Do not handle the fixture by taking its head only, but always
take its base as well.
Avoid exposing the fixture to rain or moisture to reduce the
risk of electrical shock or fire.
Do not look directly at the LED light spot while the fixture is
on.
Securely fasten the fixture’s base to a surface or rigging
hardware before applying power to prevent movement caused by the
torque reaction of the pan motor.
Use two clamps to rig the fixture and ensure both clamps are
locked with 1/4-turn fasteners turned a full 90° clockwise.
When clamping the fixture to a truss or structure at any angle
other than vertically downwards, use two clamps of half-coupler
type that completely encircle the structure when fastened.
Avoid exposing the front lens of the fixture to sunlight or any
strong light source to prevent potential fire hazards and
damage.
Avoid pointing strong light output from other fixtures directly
at the LMH 150W Spot to prevent damage to the display.
Shield or shade the head if necessary to prevent focusing
sunlight or strong light onto the fixture, which can cause fire
hazards and damage.

View Fullscreen

User Manual Instrukcja Obslugi

New improved linear prism
Nowa ulepszona pryzma linearna

MOVING HEAD LED 150W SPOT
(ver. 0523)
F7100770

User Manual ·Instrukcja Obslugi

1. INTRODUCTION

THANK YOU FOR PURCHASING LED MOVING HEAD 150W SPOT. FOR SAFETY

REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ

THE INSTRUCTIONS.

the device is from 18°C to 40°C. Operating

2. SAFETY INFORMATION

temperature of the device from 18°C to

Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive

50°C. In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs

this instruction booklet.

carried out by unskilled people can lead to

Unpack and check carefully there is no damage or malfunction. Please contact the

transportation damage before using the fixture. Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture. It’s important to ground the yellow/green

nearest authorized technical assistance center. Always use the same type spare parts. Do not connect the device to any dimmer pack. Do not touch any wire during operation

conductor to earth in order to avoid electric and there might be a hazard of electric

shock. Disconnect main power before servicing and maintenance. Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head

shock. To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture. fle housing must be replaced if they are

only, but always by taking its base.

visibly damaged.

A t e n t i o n ! fle storage temperature of Do not look directly at the LED light spot

while the fixture is on.

WARNING!

WARNING! The LMH 150W Spot has a powerful pan motor. The torque reaction when the head is panned suddenly can cause the base to move if the fixture is standing unsecured on a surface. Do not apply power to the LMH 150W Spot unless the baase is securely fastened to a surface or to rigging hardware.
WARNING! Use 2 clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock each clamp with both 1/4-turn fasteners. Fasteners are locked only when turned a full 900 clockwise.
WARNING! When clamping the fixture to a truss or other structure at any other angle than with the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
WARNING! Position or shade the head so that the front lens will not be exposed to sunlight or any other strong light source from any angle – even for a few seconds. See Figure 2. The LMH 150W Spot lens can focused the sun’s rays, creating a potential fire hazard and causing damage.
IMPORTANT! Do not point strong light output from other fixtures at the LMH 150W Spot, as intense illumination can damaged the display.

Figure 2. Lenses can focused sunlight and strong light, presenting a risk of fire and damage to the fixture. Shield or shade the head if necessary.

LED MOVING HEAD 150W SPOT ver. 0523 · Art No F7100770

3. PRODUCT INFORMATION
Light Source: Ultra bright 150W LED PAN range: 540 0 TILT range: 270 0 Color wheel: 8 main colors + open with the rainbow Effects: 2 Gobos wheels: Fixed gobo wheel and rotating Gobo wheel. 7 Gobos + White with Bi-directional rotate effect,
4. INSTALLATION

New improved linear prism – 2 facet prism rotating, Frost filter. Gobo Indexing function. Adjustable flash frequency. 16 and DMX channel mode. 3-Pin XLR DMX input/output Power supply: 110 – 240V AC, 50-60Hz Power consumption: 200 W Net Weight: 12,4kg Dimensions: H(50 )xW(40)xD(33) cm Dim. (case): H(66/54/ )xW(90)xD(57,5) cm Weight (case): 78,2 kg

fle unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. fle equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.

5. CONNECTION

fle device is equipped with the following interfaces: 1. DMX (in/out): XLR 3-pin socket 2. Power (in/out): powerCON socket
5.1 Connecting DMX signal fle connection is performed using cable with XLR-female -> XLR-Male plugs.

1 3
2

GROUND DMX + DMX –

1 3
2

FEMALE XLR

MALE XLR

CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120 resistor between signal (-) and signal (+) into a XLR plug and plug it in the DMX output of the last fixture.

DMX Controller

DMX 512

User Manual ·Instrukcja Obslugi 5.2 Voltage specification
Input Voltage 100~240V

Total Power 180W

Frequency 50/60Hz

5.3 Connecting power supply

The connection is performed using power cable with PowerCon connector (included). The device must be operated by qualified personnel.

Make sure that the power grid supply parameters are consistent with device parameters and limitations are not exceeded.

CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions.
Using lamp, the change rate of power voltage should be within ± 10%, if the voltage is too high, it will shorten the light’s life; if it’s not enough, the lamp will be dark. Please restart it after turning off light for 20 minutes until full-cooling. Frequent switching will reduce the life span of lamps and bulbs; intermittent using will improve the life of bulbs and lamps.

6. DMX CHANNELS
16 CH Mode CH Function 1 Dimmer 2 Strobe 3 Pan 4 Pan fine 5 Tilt 6 Tilt fine 7 Speed
8 Color

LED MOVING HEAD 150W SPOT ver. 0523 · Art No F7100770

Value 0-255 0-10 11-255 0-255 0-255 0-255 0-255 0-255 0-4 5-9 10-14 15-19 20-24 25-29 30-34 35-39 40-44 45-49 50-54 55-59 60-64 65-69 70-74 75-79 80-84 85-89 90-169 170-174 175-255

Description From dark to bright No Strobe From Slow to Fast Pan Pan 16 bit Tilt Tilt 16 bit Fast – Slow White White + Color 1 Color 1 Color 1 + Color 2 Color 2 Color 2 + Color 3 Color 3 Color 3 + Color 4 Color 4 Color 4 + Color 5 Color 5 Color 5 + Color 6 Color 6 Color 6 + Color 7 Color 7 Color 7 + Color 8 Color 8 Color 8 + Color 9 Color fast to slow in clockwise Stop Color slow to fast in anticlockwise

User Manual ·Instrukcja Obslugi

CH Function

Value

0-9

10-19

20-29

30-39

40-49

50-59

60-69

70-79

80-89

9 Fixed gobo wheel 90-99

100-109

110-119

120-129

130-139

140-149

150-159

160-204

205-209

210-255

0-9

10-19

20-29

30-39

Rotating Gobo wheel

40-49 50-59 60-69

70-79

80-89

90-99

100-109

Description Open White Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 White shaking Gobo 1 shaking Gobo 2 shaking Gobo 3 shaking Gobo 4 shaking Gobo 5 shaking Gobo 6 shaking Gobo 7 shaking Fast to slow in clockwise stop Slow to fast in anti clockwise Open white Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 White shaking Rotating Gobo 1 shaking Rotating Gobo 2 shaking

LED MOVING HEAD 150W SPOT ver. 0523 · Art No F7100770

CH Function

Value

110-119

120-129

130-139

140-149

150-159

160-204

205-209

210-255

0-127

Gobo wheel rotating

128-190 191-192

193-255

12 Zoom

0-255

0-49

50-99 13 Prism and Frost
100-149

150-255

0-127

14 Prism rotating

128-190 191-192

193-255

0-255

0-5

6-55

15 Macro

56-105

106-155

156-205

206-255

16 Reset

0-25 26-76

Description Rotating Gobo 3 shaking Rotating Gobo 4 shaking Rotating Gobo 5 shaking Rotating Gobo 6 shaking Rotating Gobo 7 shaking Fast to slow in clockwise STOP Slow to fast in anti clockwise Gobo angle Fast to Slow STOP Slow to Fast in anti clockwise Zoom Invalid Prism 1 Prism 2 Frost Prism angle Fast to slow in clockwise STOP Slow to fast in anti clockwise Brightness from dark to bright Invalid Demo 1 Demo 2 Demo 3 Demo 4 Random No Small motor Reset

User Manual ·Instrukcja Obslugi

20 CH Mode

CH Function

Value 77-127 128-255

Description XY Reset Whole RESET

OSTRZEENIE!
UWAGA! LMH 150W Spot posiada mocny silnik obrotu ,,pan”. Reakcja na moment obrotowy, gdy glowica zostanie nagle panoramowana, moe spowodowa ruch podstawy, jeli urzdzenie stoi niezabezpieczone na powierzchni. Nie naley wlcza zasilania do glowicy, chyba e podstawa jest bezpiecznie przymocowana do powierzchni lub zabezpieczona link bezpieczestwa. UWAGA! Uyj 2 zacisków (1/4-fastener), aby przymocowa urzdzenie. Nie zawieszaj urzdzenia tylko na jednym zacisku. Zablokuj kady zacisk za pomoc lczników 1/4 obrotu. Lczniki s blokowane tylko po obróceniu o pelne 900 zgodnie z ruchem wskazówek zegara. UWAGA! Podczas mocowania urzdzenia do kratownicy lub innej konstrukcji pod innym ktem ni z jarzmem zwisajcym pionowo w dól, naley uy dwóch zacisków typu Quick Half Coupler – (Hak). Nie uywaj zacisków, które nie przylegaj do konstrukcji po zamocowaniu. UWAGA! Ustaw lub przyciemnij Glowice, aby przednia soczewka nie byla naraona na dzialanie promieni slonecznych lub innych silnych ródel wiatla pod dowolnym ktem – nawet przez kilka sekund. Patrz rysunek 2. Soczewka Glowicy moe skupia promienie sloneczne, tworzc potencjalne zagroenie poarowe i powodujc uszkodzenia. WANE! Nie kieruj silnego strumienia wietlnego z innych urzdze na Glowic, poniewa intensywne owietlenie moe uszkodzi wywietlacz.
Rysunek 2. Soczewki mog skupia wiatlo sloneczne i silne wiatlo, stwarzajc ryzyko poaru i uszkodzenia urzdzenia. W razie potrzeby naley osloni lub zasloni glow.

LED MOVING HEAD 150W SPOT ver. 0523 · Art No F7100770
1. WPROWADZENIE Dzikujemy za zakup urzdzenia LED MOVING HEAD 150W SPOT. Ze wzgldów bezpieczestwa oraz w celu zapewnienia bezawaryjnej pracy urzdzenia naley dokladnie zapozna si z instrukcj.

2. ZASADY BEZPIECZENSTWA
Instalacja powinna by przeprowadzana
przez wykwalifikowany personel, aby zminimalizowa ryzyko przypadkowego poraenia prdem. Przed instalacj urzdzenia naley odlczy urzdzenie od sieci. Przed podlczeniem urzdzenia do sieci energetycznej naley sprawdzi, czy nie jest ono uszkodzone mechanicznie. Jeeli widoczne s jakiekolwiek lady uszkodzenia naley niezwlocznie skontaktowa si z dystrybutorem. Nie podlcza urzdzenia
do sieci elektrycznej.

U w a g a ! Temperatura przechowywania urzdzenia wynosi od 18°C do 40°C. Temperatura pracy urzdzenia wynosi od 18°C do 50°C. Aby unikn uszkodze nie naley stosowa rozpuszczalników organicznych do czyszczenia powloki urzdzenia. Urzdzenie naley instalowa na
stabilnych konstrukcjach. Urzdzenie powinno by zainstalowane
w dobrze wentylowanym pomieszczeniu, w odlegloci co najmniej 15cm od najbliszej powierzchni (ciany, sufitu itp). Jednoczenie naley upewni si, e otwory wentylacyjne nie s zatkane oraz wentylatory dzialaj poprawnie.

3. INFORMACJE O PRODUKCIE

ródo wiatla: Ultra jasna LED 150W PAN: 5400 TIL: 2700 Kolor: 8 kolorów + Open z tcz Efekty: 2 kola Gobo z rotacj i 7 zmiennymi wzorami, 2-cienny pryzmat z rotacj – Nowa ulepszona pryzma linearna, Frost filter

Ilo kanalów DMX: 16 3-Pin XLR DMX input/output Zasilanie: 110 – 240V AC, 50-60Hz Pobór mocy: 200 W Waga: 12,4 kg Wymiary: W(50)xSz.(40)xGl.(33) cm Wym. (case): W(66/54/ )xSz.(90)xGl.(57,5) cm Waga (case): 78,2 kg

4. INSTALACJA
Po wyjciu urzdzenia z opakowania naley sprawdzi czy nie zostalo ono uszkodzone podczas transportu. Przed podlczeniem do sieci elektrycznej naley upewni si, e urzdzenie zamocowane jest stabilnie. Producent nie ponosi odpowiedzialnoci za uszkodzenia spowodowane niestabilnym zamocowaniem urzdzenia.

Podczas korzystania z urzdzenia naley zadba o poprawne podlczenie go do sieci elektrycznej oraz prawidlowe uziemienie. Naley upewni si, e parametry sieci elektrycznej s zgodne z wymaganiami urzdzenia. Wszelkie czynnoci obejmujce obslug w zakresie podlczania urzdzenia do sieci elektrycznej powinny by wykonywane przez wykwalifikowany personel.

User Manual ·Instrukcja Obslugi

5. POLACZENIA

Urzdzenie wyposaone jest w nastpujce interfejsy: 1. DMX (wejcie/wyjcie) zlcza: XLR 3-pin 2. Zasilanie (wejcie/wyjcie) zlcze: powerCON

1 3
2
ESKI XLR

GROUND DMX + DMX –

1 3
2
MSKI XLR

5.1 Podlczenie sygnalu DMX Polczenie odbywa si przy uyciu przewodu z wtyczkami XLR-eski -> XLR-Mski

DMX Controller

DMX 512

5.2 Specyfikacja zasilania Napicie Zasilania 100~240V

Pobór Mocy 180W

Czstotliwo zasilania 50/60Hz

5.3 Podlczenie zasilania Polczenie odbywa si przy uyciu przewodu zakoczonego z jednej strony wtyczk sieci elektrycznej i wtyczk typu powerCON z drugiej strony (w zestawie). Urzdzenie musi by obslugiwane przez

wykwalifikowany personel techniczny. Naley upewni si, e parametry zasilania sieci energetycznej s zgodne z parametrami urzdzenia i nie zostaj przekroczone ograniczenia dotyczce poboru energii elektrycznej z sieci.

U WA G A ! W przypadku uszkodzenia przewodu nie naley dokonywa samodzielnej naprawy. Wymiana lub naprawa moe by wykonana jedynie w serwisie producenta lub przez osob z odpowiednimi uprawnieniami.

LED MOVING HEAD 150W SPOT ver. 0523 · Art No F7100770

6. LISTA KANALOW DMX
16 CH Mode

CH Function 1 Dimmer 2 Strobe 3 Pan 4 Pan fine 5 Tilt 6 Tilt fine 7 Speed
8 Color

Value 0-255 0-10 11-255 0-255 0-255 0-255 0-255 0-255 0-4 5-9 10-14 15-19 20-24 25-29 30-34 35-39 40-44 45-49 50-54 55-59 60-64 65-69 70-74 75-79 80-84 85-89 90-169 170-174 175-255

User Manual ·Instrukcja Obslugi

CH Function

Value

0-9

10-19

20-29

30-39

40-49

50-59

60-69

70-79

80-89