Decon Adv5x02dsk Adventus Dsk Adaptor Bar Universal Instruction Manual

ADV5X02DSK Adventus DSK Adaptor Bar Universal

Product Information

Product Usage Instructions

1. Safety

Symbols:

• Warning! – Risk of serious injury or death. An operation
  that, if not correctly performed, may lead to injury to the
  operator or others.
• CAUTION! – Risk of material damage. An operation that,
  if not correctly performed, may lead to material damage.
• INFO – Particularly important or explanatory
  information

General instructions:

These instructions shall always be followed when placing the
mounting ADV5 Adventus DSK adaptor bar universal on a wheelchair.
Adjustment of the Adventus wheel is described in the user manual of
the Adventus wheel.

Warnings:

WARNING! Assembly work or changes made to the mounting
set must be carried out by a trained service technician, reseller,
or another person assigned by Decon.

2. Overview

Components:

• A: Adaptor bar
• B: Fork-adaptor bar
• C: Clamps
• D: Holder
• E: QR pin
• F: Fork

INFO: The Adaptor kit can vary depending on the tube size
of the chassis and might not match the one in the picture above.
This assembly instruction shows the Adaptor kit mounted in the
lower pipes of the wheelchair.

INFO: Adaptor kit, depending on the wheelchair frame, can
be mounted on the upper or lower pipes of the wheelchair. In both
positions, the principle of mounting is the same as described in
the following chapters.

3. Mounting adaptor kit

Step 1: Mounting Clamps and Holder

1. Mount the Clamps (C) and Holder (D) on the lower pipes by using
   the provided screws, facing the two Holder (D) openings toward each
   other. Tighten the screws so that the Clamps (C) can still be moved
   along the wheelchair pipes.
2. INFO: The Clamps (C) and Holder (D) should be mounted in
   a vertical position.
3. INFO: If possible, place the screws towards the inside
   of the wheelchair for better accessibility.

Step 2: Mounting Adaptor bar

4. Mount the Adaptor bar (A) into the Holders (D) and lock it into
   place using the QR Pins (E). Tighten the screws sitting in the
   Clamps (C).
5. INFO: The QR Pins (E) can be inserted into Holder (D)
   either from the back or front sides.
6. INFO: After the screws are tightened, check that the
   Adaptor bar (A) can still be removed from the Holders (D) without
   excessive force. If the adaptor bar (A) is stuck in the Holders
   (D), loosen the screws on one side and adjust the position.

Assembly Instructions
ADV5X02DSK, ADV5X03DSK, ADV5X04DSK, ADV5X05DSK, ADV5X06DSK, ADV5X07DSK
Adventus DSK adaptor bar Universal
2022-05 Revision 0

Assembly Instructions ADV5 Adventus DSK adaptor bar Universal __________________________________________________________________________________
1. Safety
Symbols
Warning! Risk of serious injury or death. An operation that, if not correctly performed, may lead to injury to the operator or others.
CAUTION! Risk of material damage. An operation that, if not correctly performed, may lead to material damage.
INFO Particularly important or explanatory information
General instructions
These instructions shall always be followed when placing the mounting ADV5 Adventus DSK adaptor bar universal on a wheelchair. Adjustment of the Adventus wheel is described in the user manual of the Adventus wheel.
Warnings
WARNING! Assembly work or changes made to the mounting set must be carried out by trained service technician, reseller or another person assigned by Decon.
__________________________________________________________________________________ Sida 2/10

Assembly Instructions ADV5 Adventus DSK adaptor bar Universal __________________________________________________________________________________
2. Overview
F E
D

B

G

A

A Adaptor bar B Fork-adaptor bar C Clamps D Holder E QR pin F Fork

INFO The Adaptor kit can vary depending on the tube size of the chassis and might not match the one in the picture above. This assembly instruction shows the Adaptor kit mounted in the lower pipes of the wheelchair.
INFO Adaptor kit, depending on the wheelchair frame, can be mounted on the upper or lower pipes of the wheelchair. In both positions, the principle of mounting is the same as described in the following chapters.

__________________________________________________________________________________ Sida 3/10

Assembly Instructions ADV5 Adventus DSK adaptor bar Universal __________________________________________________________________________________
3. Mounting adaptor kit
First, mount the Clamps (C) and Holder (D) on the lower pipes by using the provided screws, face the two Holder (D) openings toward each other. Now tighten the screws so that the Clamps (C) can still be moved along the wheelchair pipes.
INFO The Clamps (C) and Holder (D) should be mounted in vertical position.
INFO If possible, place the screws toward inside of the wheelchair for better accessibility. __________________________________________________________________________________
Sida 4/10

Assembly Instructions ADV5 Adventus DSK adaptor bar Universal __________________________________________________________________________________
Mount the Adaptor bar (A) into the Holders (D) and lock it into place using the QR Pins (E). Now, tighten the screws sitting in the Clamps (C).
INFO The QR Pins (E) can be inserted into Holder (D) either from back or front sides.
INFO After the screws are tightened check that the Adaptor bar (A) can still be removed from the Holders (D) without excessive force. If the adaptor bar (A) is stuck in the Holders (D), loosen the screws on one side and adjust the position.
WARNING!
The screws holding the clamps (C) shall be tightened to 20-25Nm of torque. Loctite 243 or eq. must be applied. __________________________________________________________________________________
Sida 5/10

Assembly Instructions ADV5 Adventus DSK adaptor bar Universal __________________________________________________________________________________
4. Adjustment of the adaptor bar
Mount Fork-adaptor bar (B) onto Adaptor bar (A).
First, make sure that Fork-adaptor bar (B) is placed in the center of the wheelchair. Then, remove the screws in Fork (F) that locks the rotation (see picture below).
__________________________________________________________________________________ Sida 6/10

Assembly Instructions ADV5 Adventus DSK adaptor bar Universal __________________________________________________________________________________ Mount the spirit-level adjustment tool onto the fork (F). Then, adjust the height and the angle of both Fork-adaptor bar (B) and Fork (F) to a position where the spirit-level tool shows the correct angle and there is not collision with the wheelchair footrest. If possible, make sure that the fork doesn’t sit lower than the footrest and that the height, if possible, corresponds to the picture bellow.
__________________________________________________________________________________ Sida 7/10

Assembly Instructions ADV5 Adventus DSK adaptor bar Universal __________________________________________________________________________________ Reassemble the screw in the hole that is fits the best; see picture bellow as an example.
WARNING!
The screws shall be tightened to: 7-9Nm of torque (M6) 10-15Nm of torque (M8) __________________________________________________________________________________
Sida 8/10

Assembly Instructions ADV5 Adventus DSK adaptor bar Universal __________________________________________________________________________________ Now, tighten the screws that sits in the clamps on the Adaptor bar (A) and on Fork-adaptor bar (B). On both clamps, slightly tighten all screws. It is important to not completely tighten each screw, but to slowly tighten them a little at a time. Keep tightening until each of four screws on Adaptor bar (A) are secured (30-35Nm of torque) and each of two screws on Forkadaptor bar (B) are secured (9-10Nm of torque). Also, make sure one last time that the fork is centered and the angle of the sprit-level adjustment tool is still correct.
Check one last time that all screws are properly secured. Now, see the user manual of Adventus to continue the installation. This can be downloaded from www.decon.se/en/
__________________________________________________________________________________ Sida 9/10

Decon Wheel AB Södra Ekeryd 119, SE-314 93 Hyltebruk, Sweden Tel: +46 (0)345 40880 Fax: +46 (0)345 40895 E-mail: [email protected]

References

• Start - Decon