43179 Cam Buckle Pioneer Pickup Kit
Product Information
The Cam Buckle Pioneer Pickup Kit 43179 is a set of accessories
designed for use with the Rhino-Rack Pioneer Platform or Tray and
Tradie Tray. It includes pickup mouldings, cam buckles, screws,
nuts, and an Allen key.
The maximum lashing capacity of the kit is 225kg/496Lbs per set.
It is recommended to use non-stretch fastening ropes or straps for
securing loads. Overloading the Rhino-Rack Pioneer Platform/Tray or
Tradie Tray and roof bars should be avoided, and the vehicle’s roof
carrying capacity should be checked. Increased sensitivity to cross
winds should be taken into account when driving off-road due to the
increased vehicle roof height.
Regularly checking the strap condition for signs of abrasion is
important. Damaged straps should not be used and should be
immediately replaced. The roof capacity should not be overloaded,
and loads should be evenly distributed. When putting the vehicle
through an automatic car wash, the load and roof racks should be
removed.
Transporting a load on the roof can change the handling
characteristics of the vehicle. Extreme care should be exercised
when transporting large wind-resisting loads, especially when
negotiating corners and under braking.
Product Usage Instructions
- Before installation, carefully read the fitting instruction
provided with your alloy tray to ensure correct installation. - Check the contents of the Cam Buckle Pioneer Pickup Kit 43179
before starting the fitment and report any discrepancies. - Assemble the Pickup kit as shown, but do not tighten the
hardware at this stage. - Slide the Pickup Moulding into the Pioneer access slot on the
Pioneer Platform with the longer underside facing the outside
Platform. If it proves difficult, slightly loosen the
hardware. - Repeat steps 1-2 for the opposing side.
- Secure your load between two or more Pickup Mouldings on the
Pioneer Platform. Wrap the looped ends of the Cam Buckle sections
over each Moulding. - Pull the strap through the Cam Buckle and tighten it over the
load to be carried. - Ensure the load is secure before driving and tie off any loose
ends of the strap.
Note: These instructions are the property of RhinoRack Australia
Pty. Ltd. and should only be used for their intended purpose.
CONTROLLED
Important:
Cam Buckle Pioneer Pickup Kit 43179
Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the alloy tray is installed correctly. Check the contents of this kit before commencing fitment and report any discrepancies.
Important Information
Maximum Lashing Capacity: 225kg/ 496Lbs per set.
Recommendations: Use only non stretch fastening ropes or straps. Do not overload your Rhino-Rack Pioneer Platform/ Tray or Tradie Tray and roof bars. Check your vehicle’s roof carrying capacity. Exercise caution when driving off road as vehicle roof height has been increased. Be aware of increased sensitivity to cross winds.
– Regularly check strap condition for any signs of abrasion. Immediately replace. Do not use a strap that is damaged. – Do not overload roof capacity. Always evenly distribute load. – Remove load/ roof racks when putting vehicle through an automatic car wash.
Caution: The handling characteristics of the vehicle change when you transport a load on the roof. For safety reasons, we recommend exercising extreme care when transporting large wind-resisting loads; special consideration must be taken into account when negotiating corners and under braking.
Note for Dealers and Fitters: It is your responsibility to ensure instructions are given to the end user or client.
Rhino-Rack
3 Pike Street, Rydalmere,
NSW 2116, Australia.
Document No: R809
Fit time: 15min
(Ph) (02) 9638 4744
Prepared By: Kayle Everett
Issue No: 03
(Fax) (02) 9638 4822
Authorised By: Chris Murty
Issue Date: 16/05/16
These instructions remain the property of RhinoRack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.
Page 1 of 2
1
2
3
4
Pioneer Pickup Kit 43179
Repeat steps 1-2 for opposing side.
3 Secure your load between two or more Pickup
Mouldings on the Pioneer Platform. Wrap the looped ends of the Cam Buckle sections over each Moulding as shown.
5
5
Item 1 2 3 4 5 6
Component Security Allen Key 4mm M6x10mm Counter Sunk Screw M6 20×20 Square Nut Pioneer Pickup Moulding Cam Buckle for Pioneer
Fitting Instructions
Qty Part No.
1
H001
8
–
8
N025
4
SP202
2
CA1461
1
R809
35mm
35mm
102mm
1 Assemble the Pickup kit as shown. Do not tighten
hardware at this stage. M6x10 Counter Sunk Screw
4 Pull the strap through the Cam Buckle as shown.
Tighten over the load to be carried. Ensure load is secure before driving. Tie off any loose ends of the
strap.
Pickup Moulding M6 20×20 Square Nut
2 Slide the Pickup Moulding into the Pioneer access slot
as shown. If this proves difficult, slightly loosen the hardware.
1.
2.
The longer underside of the Pickup Moulding faces the outside
Platform.
3. Pick-Up Point
Pioneer Platform
4. Page 2 of 2
