True Fine Td10043fl Flush Mount Lighting Instruction Manual

TD10043FL Flush Mount Lighting

Flush Mount Lighting

The Flush Mount Lighting is a product that can be mounted on the
ceiling. It has a fixture body (A), a PC board (B), a stem (C), a
finial (D), a canopy (E), and a mounting strap (F). It is equipped
with an E26 lamp socket and can handle a maximum power of 60W. The
input voltage required is 120V.

Product Usage Instructions

1. Pass the wires through stem (C) and canopy (E) and tighten
   them.
2. Install the bulbs (not included), then screw the PC board (B)
   to the bottom nut of fixture body (A).
3. Fix mounting strap (F) to outlet box with screw (G).
4. Connect the wires according to the wiring instruction provided
   below.
5. Pass canopy (E) through the screw and fix it with finial
   (D).

Wiring Instructions

1. Insert the green grounding screw into the hole with two raised
   dimples on the mounting bar. Wrap the ground wire from the fixture
   (if supplied) around the green grounding screw, then connect it to
   ground wire from the outlet box (if not fixed on the outlet box)
   using a wire connector (not supplied). If ground wire from the
   fixture is not supplied, wrap the ground wire (if not fixed on the
   outlet box) from the outlet box around the green grounding screw
   and tighten it. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
   SUPPLY WIRES.
2. Take note of the color of the wire(s) on your fixture. Identify
   which group your fixture wire(s) falls into and connect the wires
   according to the directions below:
   [GROUP A]: Connect to Black House Wire
   [GROUP B]: Connect to White House Wire
3. Take your fixture wire(s) from [Group A] and place evenly
   against the black wire from the outlet box. Do NOT twist wires
   together before using wire connectors.
4. Fit a wire connector over the wires and screw the connector
   clockwise until you feel firmness.
5. Try gently to pull the connector off the wires. If you can pull
   the connector off, carefully re-do steps 3 and 4 as above, and
   check again for a firm connection.
6. Connect the fixture wire from [Group B] to the white wire from
   the outlet box in the same manner. Make sure no bare wires can be
   seen outside wire connectors.

Cleaning Instructions

To clean the Flush Mount Lighting, wipe the fixture with a soft
cloth. Clean glass with a mild soap. Do not use abrasive materials
such as scouring pads or powders, steel wool, or abrasive
paper.

Safety Information

Always switch off the electricity supply and allow to cool for
10 minutes before changing the light bulbs.

Contact Information

If you have any questions or concerns about the product, please
contact us at [email protected].

Instruction Manual
Flush Mount Lighting

Overview
Outlet box Black
Wire nuts Smooth
[GROUP A] G.Screw

Green(Ground)

White Ribbed

Bare copper wire(Ground)

F.Mounting strap

E.Canopy D.Finial C.Stem

A.Fixture body B.PC board

Assembly Instruction
1.Pass the wires through Stem (C) and Canopy (E) and tighten them. 2.Install the bulbs (not included), then screw the PC board (B) to
the bottom nut of Fixture body (A). 3.Fix Mounting strap (F) to outlet box with Screw (G). 4.Connect the wires according to the picture above.
(Please refer to the wiring instruction for details ) 5.Pass Canopy (E) through the screw and fix it with Finial (D).

Wiring Instruction
1. Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.

2.Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:

BLACK

WHITE

*PARALLEL WIRE (round & smooth) *PARALLEL WIRE (square & ridged)

WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER

BROWN, GOLD OR BLACK WITHOUT TRACER

BROWN, GOLD OR BLACK WITH TRACER

3.Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors. 4.Fit a wire connector over the wires and screw the connector clockwise until you feel firmness. 5.Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
6.Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.
Product Specifications
Input voltage 120V Rated power 60W MAX Lamp socket E26
Product Packaging
Fixture body × 1 Stem × 1 PC board × 1 Mounting strap × 1 & Canopy × 1 Screw × 2 & Wire nut × 3 Lamp instruction × 1

Cleaning

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Safety Information

Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.

CONTACT US
E-mail:[email protected]

Print in china

References

• Digital Services, Technology and Consulting | Reply