4960 Wi-Fi 6 Smart Mesh Access Point
Air 4960 Wi-Fi 6 Smart Mesh Access Point
The Air 4960 is a Wi-Fi 6 smart mesh access point with multiple
ports and buttons for easy usage. The device has gigabit Ethernet
ports, a WPS button, a power on/off button, a reset button, and an
external power supply. It is designed to work indoors and under
room temperature conditions only.
- Status LED
- Gigabit Ethernet Ports
- WPS Button
- Power On/OFF Button
- Reset Button
- External Power Supply
Please remove the protective plastic on the device before
installation.
Installation
To install the Air 4960, download the Airties Vision application
on your mobile device by scanning the QR code provided. Follow the
instructions in the mobile application to complete your setup.
Tips for Best Performance
For best performance, keep devices away from potential sources
of electrical interference, large metal surfaces and objects,
sources and areas of heat such as ovens and sun rooms as well as
direct sunlight. Use the device in an upright position to allow for
proper ventilation. Do not block or cover openings. Avoid placing
the device in very cold, very hot, very humid or very dry locations
inside your home.
To change advanced settings on your device, access web UI with
the credentials below:
- Username: admin
- Password: Admin123
Returning to Factory Settings
To return the device to factory settings, press down on the
reset button (in the small opening on the back shown above) for 5
seconds and release. A metal paperclip (with an extended tip) or
strong toothpick are typically good choices for this task. When the
reset process is triggered, the LED in the front will blink rapidly
and the device will reboot to factory settings.
Product Notices
The Air 4960 supports the following frequencies:
- 2.4 GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40),
802.11ax (HE20), 802.11ax (HE40) - 5 GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac
(VHT20), 802.11ac (VHT40), 802.11ac (VHT80), 802.11ac (VHT160),
802.11ax (HE20), 802.11ax (HE40), 802.11ax (HE80), 802.11ax
(HE160)
Troubleshooting
| Condition | Power OFF LED Color | LED Behavior | Timing | Explanation | Recommended Action(s) |
|---|---|---|---|---|---|
| Power ON, booting | White | LED is steady green with a short blink every 5 seconds. | No action required. If the device was just powered on, please wait for at least 2 minutes for the device to boot up. | ||
| Wireless network healthy | Green | Device configured as single wireless access point. | The device is connected to the router/gateway with an Ethernet cable and acts as a wireless access point. No other mesh devices are configured in the network. | ||
| Unconfigured mesh device | Blue | The device is not configured and connected to the wireless mesh network. | |||
| Weak connection to the wireless mesh network | Red | Blinking | 1/2 second OFF 1/2 second ON | The device is part of the wireless mesh network but unable to find any of its mesh partners. | |
| Cannot connect to the wireless mesh network | Red | Solid | |||
| Software upgrade | Blue | Blinking | 4 seconds OFF 4 seconds ON | The device is retrieving the latest software. |
Air 4960
Wi-Fi 6 Smart Mesh Access Point
User Manual
PORTS and BUTTONS
Status LED
Gigabit Ethernet Ports
WPS Button
Power On/OFF Button
Reset Button
External Power Supply
!
Please remove the protective plastic on the products before installation.
INSTALLATION
To install the Airties Wireless devices, please download “Airties Vision” application on your mobile device by scanning this QR code.
Please follow the instructions in the mobile application to complete your setup.
TIPS FOR BEST PERFORMANCE
Keep devices away from: Potential sources of electrical interference. Equipment that may potentially cause interference include home security systems, microwaves and consumer electronic devices.
Large metal surfaces and objects.
Sources and areas of heat such as ovens and sun rooms as well as direct sun light.
Please make sure to remove the protective plastic on the device before first use.
Please use the device in upright position. The openings are provided for ventilation, do not block or cover openings.
Your device is designed to work indoors and under room temperature conditions only. Avoid placing the device to very cold, very hot, very humid or very dry locations inside your home.
To change advanced settings on your device, you can access web UI with the credentials below:
Username: admin Password: Admin123
RETURNING TO FACTORY SETTINGS
To return the device to factory settings, press down on the reset button (in the small opening on the back shown above) for 5 seconds and release. A metal paperclip (with an extended tip) or strong toothpick are typically good choices for this task. When the reset process is triggered, the LED in the front will “blink rapidly” and the device will reboot to factory settings.
PRODUCT NOTICES
· Operational modes:
2.4
GHz:
802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ax (HE20), 802.11ax (HE40)
5
GHz:
802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80), 802.11ac (VHT160), 802.11ax (HE20), 802.11ax (HE40), 802.11ax (HE80), 802.11ax (HE160)
TROUBLESHOOTING
Condition Power OFF
LED Color LED Behavior Timing
OFF
–
Power ON, booting Wireless network healthy
White Green
Device configured as single wireless access point
Green
Unconfigured mesh device
Blue
Weak connection to the wireless mesh network
Red
Cannot connect to the wireless Red mesh network
Software upgrade
Blue
Blinking Blinking Solid Blinking Solid Blinking Blinking
5O milliseconds OFF 5 seconds ON
4 seconds OFF 4 seconds ON
1 second OFF 1 second ON 1/2 second OFF 1/2 second ON
Explanation
Device is turned off.
LED is steady green with a short blink every 5 seconds. Device is connected to the router/ gateway with an ethernet cable and acts as a wireless access point. No other mesh devices are configured in the network. Device is not configured and connected to the wireless mesh network.
Device is part of wireless mesh network but unable to find any of its mesh partners.
Device is retrieving the latest software.
Recommended Action(s)
Make sure the power button on the back is pressed and power supply unit is connected to the device. No action required. If the device was just powered on, please wait for at least 2 minutes for the device to boot up.
No action required.
No action required, more mesh devices can be added to the wireless mesh network if needed.
Configure the device using Airties Vision app.
Bring device closer to another device in the wireless mesh network.
Make sure other device(s) that are part of the wireless mesh network are powered on and close enough to connect.
Wait for the upgrade to complete. Device will automatically start with the latest software.
