Tronic Pro Electronic Lock
Product Information
The Tronic Pro is a product that requires assembly and comes
with a drilling template. It includes right and left hand doors and
is designed to be used with an 18mm panel thickness. The product
also includes accessories such as screws and a T20 Torx Security
screw.
Product Usage Instructions
- Start by assembling the right hand door. Use the drilling
template provided to drill holes with a diameter of 2.5mm. - Repeat step 1 for the left hand door.
- Attach the right door assembly using section A-A as a
guide. - Attach the left door assembly using section A-A as a
guide. - Connect the blue part of the right door to the side of the
ledge. Ensure it is securely connected. - Connect the blue part of the left door to the side of the
ledge. Ensure it is securely connected. - Verify that the cable is properly connected and straight at the
bottom. - Release the batteries by unscrewing the T20 Torx Security screw
located on the opposite side of the battery case. - Check that the batteries are correctly inserted according to
the indicated polarity in the battery box. - Ensure that the battery pack remains connected during the
battery release process to avoid losing time configuration on the
internal clock. - Make sure not to fasten the screws too tight during
assembly.
Note: Do not push any key during the wire assembly process.
Tronic Pro
Assembly
Drilling template
ASSEMBLY
Right hand door
TRONIC PRO : Drilling t
2,5
ø8,1
ø4,5 For housing the screw head
TRONIC PRO : Drilling template
Left hand door
2,5
ø8,1
ø4,5 For housing the screw head
Accessories
ASSEMBLY
C ø5×29.5 E ø3.5×9.5 F Strike plate D M3x18
Right door assembly
ASSEMBLY
A
A
A
18 mm
panel thickness
1
2
18 + x mm
Section A-A
ø3.5 ø22
Right door assembly
ASSEMBLY
3
4
Right door
! Warning: Connect blue part to the side of the legde
5
6
Right door
Left door assembly
ASSEMBLY
A
A
B
Section A-A
18 mm
panel thickness
1
2
ø3.5 ø22
Left door assembly
ASSEMBLY
3
4
Left door 5
! Warning: Connect blue part to the side of the legde
6
Left door
Important notes
ASSEMBLY
1
Verify that the cable is properly
Don’t push any key during the wire
connected (straight and untill
assembly process.
the bottom).
2
Relase the batteries thanks to
T20 Torx Security screw located
on the opposite of the battery case
Verify that the batteries are in the right polarity (as indicated in the battery box).
T20 Torx security
IMPORTANT The battery pack must remain connected during the release of the batteries. Otherwise, the internal clock will lose the time configuration.
Important notes
ASSEMBLY 3
Verify that the screws are not fastened too tight (<20kgf/cm2). 4
Verify that the latch works smoothly in and out, without any frinction with the door frame.
LED lights
ASSEMBLY
After introducing the correct code and pressing ENTER, the three LEDs blink at the same time (green-yellow-red) and the lock does not work.
Dead batteries: replace batteries.
After pressing any button the yellow LED blinks.
Dead or almost dead batteries: replace batteries.
Batteries
ASSEMBLY
1. Make sure the battery pack contains full powered batteries (don’t screw the battery pack too tight to avoid breaking the mechanism)
2. If the lock is closed, introduce the user code (or the master one) to open it.
3. Replace the old batteries for new ones and disconnect the battery pack.
Important
We suggest to change once every three years the batteries for ensure their good condition. After a long time, the batteries can deteriorate
and damage the lock, especially in hot environments
Do not clean the locks with cleaning
products with hydrochloric acid, lye or corrosive components, especially on the metallic parts.
