R12 Carbon Fiber Bicycle Frameset
Product Information
The Yoeleo R12 frameset comes with all the necessary components
to assemble the bike. The component parts are listed from 1-14 and
include the frame, fork, rear and front axles, seatpost, saddle
clamp, headset bearings, stem bolts, spacers, bottle cage bolt,
cable grommet and hole cover, sponge tube, and brake and gear
housing.
Frameset Diagrams
The frameset diagrams provide a visual representation of the
different components and their placement on the bike.
Brake & Gear Housing Routing – Mechanical
The brake and gear housing should be routed into the down tube
of the frame from the hole where each house comes out. Before
cutting the housing, measure the correct length of the brake and
shifter housing.
Headset Bearing Installation
Prior to installing the bearings, route the cable housing first.
Lightly grease the contact point between metal and carbon surface
to prevent damage to the bike.
Spacers Installation
Choose the right spacer height to adjust your riding position.
Ensure that you route the housing inside bearing cover ring before
routing it inside the handlebar.
Handlebar Internal Routing
Route housing to the lever from the provided hole. Ensure that
you put the compression plug into the steerer tube.
Seatpost Installation
If needed, change the height of the seat and cut off any extra
length. Remember that the minimum insertion is 10 CM. Change the
saddle’s position forward and backward using the saddle angle
adjuster. To tighten the seatpost wedge, turn the bolt clockwise.
Use a torque wrench set at 8Nm.
Mount Fixing Points
Observe the bolt’s length before attempting to tighten it.
Tighten the bottle cage bolt with a torque wrench set at 4Nm.
Safety
Properly tighten hardware to the specified torque.
Over-tightening hardware could deform or break the hardware or
components. Under-tightening hardware could cause hardware or
components to become loose. Always apply threadlocker to all
reused-fasteners with pre-applied threadlocker before
re-assembly.
Product Usage Instructions
- Route the brake and gear housing into the down tube of the
frame from the hole where each house comes out. Measure the correct
length of the brake and shifter housing before cutting. - Prior to installing the bearings, route the cable housing
first. Lightly grease the contact point between metal and carbon
surface to prevent damage to the bike. - Choose the right spacer height to adjust your riding position.
Ensure that you route the housing inside bearing cover ring before
routing it inside the handlebar. - Route housing to the lever from the provided hole. Ensure that
you put the compression plug into the steerer tube. - If needed, change the height of the seat and cut off any extra
length. Remember that the minimum insertion is 10 CM. Change the
saddle’s position forward and backward using the saddle angle
adjuster. To tighten the seatpost wedge, turn the bolt clockwise.
Use a torque wrench set at 8Nm. - Observe the bolt’s length before attempting to tighten it.
Tighten the bottle cage bolt with a torque wrench set at 4Nm. - Always tighten hardware to the specified torque.
Over-tightening hardware could deform or break the hardware or
components. Under-tightening hardware could cause hardware or
components to become loose. Always apply threadlocker to all
reused-fasteners with pre-applied threadlocker before
re-assembly.
·
·
·
FRAMESET USER
MANUAL
www.yoeleobike.com @yoeleo Yoeleo
Frameset Diagrams
The R12’s component parts are listed from 1 14 . You will receive all the parts inside your package.
Rear brake hose Front derailleur cable Rear derailleur cable Front brake hose Sponge tube
Seatpost Seatpost clamp 9
12 Bottle cage bolt
13 Hanger bolts
14 Cable Grommet and Hole Cover
15
Saddle clamp Stem bolts nut 2 Stem bolt 3 Spacers 4 Bearing cover 5
Frame
1 Top cap
Handlebar 6 Compression plug 7 Split ring 8 Headset bearings
Fork
Rear Axle Rear derailleur hanger
Thru-Axle Nut
10 Front derailleur hanger
Front Axle
Frameset User Manual
Brake & Gear Housing Routing – Mechanical
Route the housing into the down tube of the frame from the hole where each house comes out. Please measure the correct length of the brake and shifter housing before cutting.
Rear brake hose Front derailleur cable Rear derailleur cable Front brake hose Sponge tube
Cable grommet 14
Rear derailleur hanger 13 Hanger bolts 3Nm
Thru-Axle Nut
Frameset User Manual
Headset Bearing Installation
Please route the cable housing FIRST before install the bearings. Lightly grease the contact point between metal and carbon surface.
Compression plug 6
Stem bolts nut 2 6Nm Stem bolt 3
Split ring 7
Frame
1 Top cap Handlebar
4 Spacer (10mm) 4 Spacer (10mm) 4 Spacer (5mm) 5 Bearing cover
(10mm) 8 Headset bearings
Fork
Frameset User Manual
Spacers Installation
Pick the right spacer height to adjust your riding position. Remember to route the housing inside bearing cover ring before routing inside the handlebar.
Spacer (10mm) 4
Spacer (10mm) 4 Spacer (5mm) 4 Bearing cover 5
(10mm)
Split ring 7
Handlebar Internal Routing
Route housing to the Lever from this hole.
6 Compression plug 9Nm
Compression Plug
Put the compression plug into the steerer tube.
1 Top cap
Top Cap Bolt Tightening
Eliminate play in the steering tube by tightening top cap bolt.
Frameset User Manual
Seatpost Installation
If needed, change the height of the seats and cut off any extra length. Remember that the minimum insertion is 10 CM.
Saddle Clamp Assembly
Saddle Angle Adjuster
9 Seatpost clamp
Saddle Wedge Slider
Change the saddle’s position forward and backward.
Seatpost Tightening
To tighten the seatpost wedge, turn the bolt clockwise. For this step, you should always use a torque wrench set to 8Nm .
Frameset User Manual
Mount Fixing Points
Carefully observe the bolt’s length before attempting to tighten.
12 Bottle cage bolt*4 4Nm
Bottle cage
Frameset User Manual
Safety
WARNING
Properly tighten hardware always tighten hardware to the specified torque.
Over-tightening hardware could deform or break the hardware or components. Under-tightening hardware could cause hardware or components to become loose. Either situation could damage the bicycle and result in injury to the rider.
WARNING
Reapply threadlocker
All reused-fasteners with pre-applied threadlocker must be cleaned with isopropyl alcohol and have new thread locker applied before re-assembly. If threadlocker is not applied, the fasteners may loosen which could damage the bicycle and result in injury to the rider.
Legend
Apply appropriate grease Apply threadlocker Nm Torque Cable (zip) tie
Frameset User Manual
Di2 wire
A Quick guide for installation
Shifting cable and brake house routing
Rear brake hose Front derailleur cable
Rear derailleur cable Front brake hose
Internal Routing Frameset
In order to use the complete internal cables routing, the frame and the fork have to be compatible. Fork: The fork must have a hole for the entrance of the brake front cable in the fork-tube to allow the cable routing up to the exit near front brake caliper.
Traditional Frameset
In case of assembling on traditional frameset, cables will enter close to the levers and will go out from central holes. Here above a picture showing the cables passages.
Handlebar Installation Guide
Shifter/Brake lever Installation
Carefully observe the bolt’s length before attempting to tighten. Use torque wrench to tighten the bolt around 6-8Nm
Di2 11-Speed cable routing diagram
Shifter Angle Adjustment
Follow line marks on both side of the bar to level left and right shifter. Apply carbon paste for better grip.
Route the cable in to the Junction Box.
Junction box A Junction Box B (Optional)
Handlebar Installation Guide
2 Computer heads
3 GoPro style accessory mount
5 Rubber Strap for Lights
1 Computer Holder Main Arm 7 Fixing Bolts group
6 Main Arm Fixing Bolt Spacers
Light Mount 4
Installation Guide
Integrated Handlebar Computer Holder
0.8Nm Fixing bolt 7
2 GIANT
2 GARMIN 2 BRYTON 2 WAHOO
1 Computer Holder Main Arm 3 GoPro style accessory mount
Main Arm Fixing Bolt Spacers 6 4Nm Fixing Bolt 7
Integrated Handlebar Computer Holder Installation Guide
Installation Guide
Integrated Handlebar Computer Holder
4Nm Fixing Bolt 7 Light Mount 4
Rubber Strap for Lights 5
Integrated Handlebar Computer Holder Installation Guide
FRAMESET USER MANUAL
Carbon Bicycle Frames | Road Disc Brake Bikes | Bike Wheels China – YOELEO
