Ciro 60200 Adjustable Passenger Comfort Peg Mounts Instruction Manual

60200 Adjustable Passenger Comfort Peg Mounts

Product Information: Adjustable Passenger Comfort Peg
Mounts

The Adjustable Passenger Comfort Peg Mounts is a product
designed to provide additional comfort to the passenger of a
motorcycle. It allows the passenger to adjust the position of their
feet to their preferred height and angle while riding. The product
comes with two mounts, two extension arms, two clevis, and a
hardware kit that includes 2 3/8- 16×2 SHCS, 2 3/8- 24 x 7/8 SHCS,
2 3/8- Split lock washers, 2 3/8- 24 x 1-1/8 SHCS, and 2 D spring
washers.

The installation of the product requires some technical
knowledge and should be done carefully following the instructions
provided in the manual to ensure safety and functionality.

Product Usage Instructions:

1. Park the motorcycle on a level surface and turn off the engine.
   Allow the engine to cool before installation.
2. Remove the top SHCS from the stock footrest and loosen the
   lower SHCS. Adjust the OEM footrest mount into either of the two
   lower positions. Replace the upper SHCS and tighten it. Tighten the
   lower as well.
3. Preassemble the Ciro mount and extension arm with the 3/8- 16 x
   2 SHCS and 3/8 split lock washer.
4. The Ciro mount must be located immediately above the head of
   the OEM peg mount bolt. Holding the assembly together, thread the
   3/8- 16 x 2 SHCS into the motorcycle frame using a 5/16 hex wrench
   until secure. Do not fully tighten yet.
5. Pre-installed button cap allen screw must be in the top
   position for pegs to work correctly. Using a 3/8-24 x 7/8 SHCS and
   3/8 split lock washer, install the Ciro clevis onto the Ciro arm
   with a 5/16 hex wrench until secure. Do not fully tighten yet.
6. Place the D spring washer in clevis with the flat side at the
   back. Push in footpeg and secure with 3/8-24 x 1-1/8.
7. Adjust the peg mounts to the desired position and torque each
   SHCS to 36-42 ft/lbs.
8. Repeat steps 2-7 on the other side of the bike.

It is important to follow the instructions carefully and ensure
that all parts are securely tightened before using the product.
Failure to do so may result in potential serious injury or death if
not followed.

Adjustable passenger comfort peg mounts
WARNING This indication alerts you to the fact that ignoring the contents described herein can result in potential serious injury or death if not followed.
CAUTION This indication alerts you to the fact that ignoring the contents described herein can or will result in material damage and/or personal injury.
ATTENTION This indication alerts you to the fact if you ignore this detail you will affect the performance or functionality of the product.
All Ciro products are designed for “easy assembly” and/or “plug and play”. We recommend a competent mechanic install our products, using standard mechanical procedures to assure a safe and successful installation. Read completely and understand the instructions prior to starting installation. NOTE: Ciro products are designed and manufactured under very strict quality control. Ciro warrants that products sold to the original purchaser shall be free from any defects in materials and workmanship for a period of 3 (three) years from the date of purchase, and a limited lifetime warranty against LED failure. Ciro will have no obligation if the customer cannot show proof of purchase. Warranty will not be granted unless the part is properly installed, unmodified and maintained. Ciro will not be liable for any consequential and incidental damages, including labor, or non-Ciro products. Please visit Ciro3d.com for our complete warranty policy.
Parts Included: 2 Mounts 2 Extension arms 2 Clevis 1 Hardware kit including: 2 3/8″- 16×2″ SHCS 2 3/8″- 24 x 7/8″ SHCS 2 3/8″- Split lock washers 2 3/8″- 24 x 1-1/8″ SHCS 2 D spring washers

Installation Instructions: 1. Park on a level surface and shut off the motorcycle. Ensure that the engine has time to cool before installation.
2. The stock footrest will be in the top position and will need to be moved down. Remove top SHCS and loosen lower SHCS and adjust the OEM footrest mount into either of the two lower positions. Replace upper SHCS and tighten. Tighten lower as well. Fig. 1
3. Preassemble the Ciro mount and extension arm with the 3/8″- 16 x 2″ SHCS and 3/8″ split lock washer. Fig. 2
4. The Ciro mount must be located immediately above the head of the OEM peg mount bolt. Holding the assembly together, thread the 3/8″- 16 x 2″ SHCS into the motorcycle frame using a 5/16″ hex wrench until secure. Do not fully tighten yet. Fig. 3

Fig.1

Fig.2

Stock Position Lowered for peg mount
G60200, REV._A For the latest version of installation instructions visit www.ciro3d.com

Page 1 of 2

Fig.3

Fig.4

Button Cap allen screw

5. Pre installed button cap allen screw must be in top position for pegs to work correctly. Fig. 4. Using a 3/8″24 x 7/8″ SHCS and 3/8″ split lock washer, install the Ciro clevis onto the Ciro arm with a 5/16″ hex wrench until secure. Do not fully tighten yet. Fig. 4

6. Place the D spring washer in clevis with flat side at back. Push in footpeg and secure with 3/8″- 24 x 1-1/8″

Fig.5

Fig.6

D Spring washer

7. Adjust peg mounts to desired position and torque each SHCS to 36-42 ft/lbs. 8. Repeat steps 2-7 on other side of bike.
Fig.7

G60200, REV._A For the latest version of installation instructions visit www.ciro3d.com

Page 2 of 2

References

• Ciro3D: Motorcycle Accessories & Parts
• Ciro3D: Motorcycle Accessories & Parts