K4006 Power Supply
Product Information:
- Total solder points: 36
- Difficulty level: beginner 1 2 3 4 5 advanced
- Power supply for K4004B and K4005B
- K4006
- ILLUSTRATED ASSEMBLY MANUAL H4006IP-1
Product Usage Instructions:
- Assembly Hints:
- Make sure you have the right tools, including a basic
multi-meter for some projects. - Always look for possible last minute manual updates indicated
as ‘NOTE’ on a separate leaflet.
- Mount the component against the PCB surface and carefully
solder the leads. - Make sure the solder joints are cone-shaped and shiny.
- Trim excess leads as close as possible to the solder
joint.
- Refer to the HALG (general manual) or visit our website for the
color code for resistances and LEDs: http://www.velleman.be/common/service.aspx - Follow the PCB layout and diagram for assembling the
components.
- Refer to the provided table for the connection details based on
the specific product model (K4004B, K4005B). - Ensure correct polarity for LEDs, bridge rectifier, and
electrolytic capacitors.
For any further assistance or inquiries, please contact VELLEMAN
Components NV:
Address: Legen Heirweg 33, 9890 Gavere, Belgium, Europe
Website: www.velleman.be,
www.velleman-kit.com
Product Support: +32 410329 311575
Total solder points: 36 Difficulty level: beginner 1 2 3 4 5 advanced
Power supply for K4004B and K4005B
K4006
ILLUSTRATED ASSEMBLY MANUAL
H4006IP-1
Assembly hints
1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
· A good quality soldering iron (25-40W) with a small tip. · Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called `thinning’ and will
protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning. · Thin raisin-core solder. Do not use any flux or grease. · A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes. · Needle nose pliers, for bending leads, or to hold components in place. · Small blade and Phillips screwdrivers. A basic range is fine.
0.000
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
Make sure the skill level matches your experience, to avoid disappointments. Follow the instructions carefully. Read and understand the entire step before you perform each operation. Perform the assembly in the correct order as stated in this manual Position all parts on the PCB (Printed Circuit Board) as shown on the drawings. Values on the circuit diagram are subject to changes. Values in this assembly guide are correct* Use the check-boxes to mark your progress. Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as `NOTE’ on a separate leaflet.
2
1.3 Soldering Hints : 1- Mount the component against the PCB surface and carefully solder the leads
2- Make sure the solder joints are cone-shaped and shiny 3- Trim excess leads as close as possible to the solder joint
Assembly hints
REMOVE THEM FROM THE TAPE ONE AT A TIME !
AXIAL COMPONENTS ARE TAPED IN THE CORRECT MOUNTING SEQUENCE !
You will find the colour code for the resistances and the LEDs in the HALG (general manual) and on our website: http://www.velleman.be/common/service.aspx
3
Construction
1. 1W Resistors
R…
4. Fuse + fuseholder
F…
R1 : 2K7 (2 – 7 – 2 – B) R2 : 2K7 (2 – 7 – 2 – B)
2. LEDs. Watch the polarity!
LD1 LD2
CATHODE
LD…
F1 : 6,3A slow F2 : 6,3A slow
5. PCB mounting tab
-V (2x) GND (2x) +V (2x)
3. Screw terminal
J1 4
6. Bridge rectifier B1 : RS603
(6A – 200V)
Watch the polarity!
7. Electrolytic Capacitors. Watch the polarity !
C3 : 10.000µF C4 : 10.000µF
C…
C1 : Optional C2 : Optional
Ordernr C1 & C2 : 10000LPOJ
8. Flat receptacle
6 x
Wire Insulation sleeve Flat receptacle
9. Connection +V
K4006 GND -V
Needs transformer :
K4005B K4005B K4005B K4004B K4004B K4004B
Connection
+V GND -V
K4004B, K4005B
Speaker 2 x 8 ohm 2 x 4 ohm 1 x 8 ohm
Power supply 2 x 30VAC / 225VA 2 x 21VAC / 300VA 2 x 21VAC / 300VA
Transformer Type 22530 Type 30021 Type 30021
2 x 8 ohm
2 x 18VAC / 160VA
Type 16018
2 x 4 ohm
2 x 18VAC / 225VA
Type 22518
1 x 8 ohm
2 x 18VAC / 225VA
Type 22518
5
PCB 10. PCB layout.
6
11. Diagram
Diagram 7
VELLEMAN Components NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be
www.velleman-kit.com
Modifications and typographical errors reserved © Velleman Components nv. H4006IP – 2004 – ED1
5 410329 311575
Velleman – Wholesaler and developer of electronics
