Velleman Visp1 Pan Or Tilt Unit User Manual

VISP1 PAN or TILT Unit

VISP1 PAN/TILT UNIT

Product Information:

Product Usage Instructions:

1. Installation:
   • The unit is intended to be mounted on a Wall Mount.
   • Installation of the pan and tilt drive to the wall mount
     requires a stainless steel 1/4-20 screw supplied with the wall
     mount.
   • Note the ribs on the underside of the unit base engage slots in
     the mount. This allows positioning of the unit in any of four
     directions with respect to the wall mount.
   • Secure unit to the wall mount using screw from underside of
     wall mount into unit and tighten.
2. Wiring of Unit:
   • Fabricate the interconnecting cable in accordance with Figure 1
     for proper operation.
   • POWER (red)
   • COMMON (black)
   • TILT DOWN (yellow)
   • TILT UP (blue)
   • PAN RIGHT (green)
   • PAN LEFT (white)
3. Inverted Mounting:
   • When the unit is mounted in the inverted position, the
     left-right directions are reversed for manual operation.
   • This must be corrected when wiring the cable between control
     unit and the pan and tilt drive. Simply reverse leads going to
     terminals 3 and 4.
4. Adjusting Limit Stops:
   • After cable is installed and unit has been mounted, proceed as
     follows:
   • Plug control unit into AC 24V source. Be sure auto switch is in
     the OFF position.
   • To adjust pan limit stops (see Figure 2), loosen screws
     securing both stops (1) and (3) to unit. Slide stops around unit to
     desired locations and secure by tightening screws.
   • To adjust tilt limit stops (see Figure 2) located in each end
     plate, remove two screws securing each end cap to unit. Loosen and
     adjust tilt limit stop screws for desired tilt limit position.
     Tighten limit stop screws and reinstall each end cap to unit and
     secure with two screws.
5. Maintenance:
   • This pan and tilt drive requires no lubrication or maintenance
     for the life of the unit.
   • If the unit fails to function, turn it off and check the fuse
     on the control unit. Replacement fuse values are given in the
     instructions supplied with the control unit.

VISP1
PAN/TILT UNIT
USER MANUAL
1. INSTALLATION
The unit is intended to be mounted on a Wall Mount. Installation of the pan and tilt drive to the wall mount requires a stainless steel 1/4-20 screw supplied with the wall mount. Note the ribs on the underside of the unit base engage slots in the mount. This allows positioning of the unit in any of four directions with respect to the wall mount. Secure unit to the wall mount using screw from underside of wall mount into unit and tighten.
2. WIRING OF UNIT
Fabricate the interconnecting cable in accordance with Figure 1. for proper operation.

POWER (red) COMMON (black) TILT DOWN (yellow) TILT UP (blue) PAN RIGHT (green) PAN LEFT (white)

Figure 1 Cable Assembly Diagram

3. INVERTED MOUNTING

When the unit is mounted in the inverted position, the left-right directions are reversed for manual operation. This must be corrected when wiring the cable between control unit and the pan and tilt drive. Simply reverse leads going to terminals 3 and 4.

4. ADJUSTING LIMIT STOPS

After cable is installed and unit has been mounted, proceed as follow : 1. Plug control unit into AC 24V source. Be sure auto switch is in the OFF
position.

VSCP1-VISP1

1

VELLEMAN

2. To adjust pan limit stops (see Figure 2), loosen screws securing both stops (1) and (3) to unit. Slide stops around unit to desired locations and secure by tightening screws.
3. To adjust tilt limit stops (see Figure 2) located in each end plate, remove two screws securing each end cap to unit. Loosen and adjust tilt limit stop screws for desired tilt limit position. Tighten limit stop screws and reinstall each end caps to unit and secure with two screws.

Figure 2 Limit Stop Adjustment and Camera Mounting Plate

VSCP1-VISP1

2

VELLEMAN

1. Right Pan Limit Stop 2. Limit-Switch Actuator 3. Left Pan Limit Stop 4. Tilt Limit Stop Screw 5. Camera Mounting Plate 6. Screw 7. Down Limit Stop 8. 4-conductor cable for video signal 9. Connection to control (VSCP1) 10. Video Output

5. MAINTENANCE

This pan and tilt drive requires no lubrication or maintenance for the life of the unit. If the unit fails to function, turn it off and check the fuse on the control unit. Replacement fuse values are given in the instructions supplied with the control unit.

6. SPECIFICATIONS

Angular travel : Limited Stop : Speed :
Load Rating : Duty Cycle :
Input Voltage : Power Consumption : Normal Operating Current : Cable Requirement : Operating Temperature : Construction : Finish : Dimensions : Weight :

Pan : 350° / Tilt : ± 75° Externally adjustable Pan : 6° / second Tilt : 4° / second Pan : 7 kg / Tilt : 5 kg Pan : continuous Tilt : intermittent AC 24V 6W 24V-200mA Six-conductor, unshielded -5°C to + 60°C Aluminium and plastic Off white baked enamel finish 150 x 160 x 200mm 2.3 kg

VSCP1-VISP1

3

VELLEMAN

VSCP1 PAN/TILT SCANNER CONTROL USER MANUAL

Feature : Auto on : LED – Green Bypass on : LED – Red Non light during off Special screw terminal-detachable connector easy for installation

Specifications :

Tilt control :

Push Button, UP/DOWN

Pan control :

Push Button, LEFT/RIGHT

Power control :

Slide Switch MAN/OFF/AUTO

Input Voltage :

AC 220-230V

Output Voltage to Scanner : AC 24V

Temperature Operating : -10°C to +60°C

Connector :

Screw Terminal-Detachable

Construction :

Steel, Off-White Textured

Dimensions :

212 x 218 x 45mm

Weight :

1.2Kg

VSCP1-VISP1

4

VELLEMAN

Operations :

FRONT PANEL 1. Power :

Push the rocker switch to “AUTO”, the Green LED will illuminate. Scanner automatic left and right adjust.

Push the rocker switch to “MAN”, the Red LED will illuminate. Scanner adjust by manual.

Non light during “OFF” 2. UP AND DOWN : Paddle switch, UP/DOWN 3. LEFT AND RIGHT : Paddle switch, LEFT/RIGHT

BACK PANEL 1. AC POWER : 2. LEFT : 3. RIGHT : 4. COM : 5. UP : 6. DOWN :

Terminal block no. 1 point Terminal block no. 2 point Terminal block no. 3 point Terminal block no. 4 point Terminal block no. 5 point Terminal block no. 6 point

VSCP1-VISP1

5

VELLEMAN