2799-695 Auresa 20 Inch 3 Light Coal Globe Semi-Flush Mount

Product Information:

The product is a light fixture with the item number
2799-695/66A. The installation instructions were updated on April
15, 2022. The fixture requires three candelabra (T8) bulbs, each
with a maximum wattage of 40 watts (not included). The fixture
comes with a circular strap (Set# A-021), ground screw, two
mounting screws, and a glass cover. The fixture should be installed
on a junction box, which is not included.

Product Usage Instructions:

1. Turn off the power at the fuse box or circuit breaker and
   remove the old fixture, including the mounting hardware.
2. Unpack the new fixture carefully and lay out all the parts on a
   clean surface, making sure not to lose any small parts necessary
   for installation.
3. Thread screws into pre-drilled holes on the circular strap,
   spaced same distance apart as holes in canopy, and tighten with
   nuts.
4. Attach the circular strap to the junction box using mounting
   screws. The side of the circular strap marked GND must face
   out.
5. Run the wires through the central tube of the canopy.
6. Connect the fixture to the central pipe of the canopy.
7. Install three candelabra (T8) bulbs, each with a maximum
   wattage of 40 watts (not included), in accordance with the fixture
   specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
8. Screw the glass cover onto the fixture, being careful not to
   over tighten.
9. Connect the electrical wires as shown in Fig.2, making sure
   that all wire connectors are secured. If your junction box has a
   ground wire, connect the fixture’s ground wire to it. Otherwise,
   connect the fixture’s ground wire directly to the circular strap
   using the green screw provided.
10. Tuck wire connectors neatly into the junction box.
11. Place the canopy over screws and secure with finials. The
    installation is now complete.
12. Turn on the power at the junction box and test the
    fixture.

INSTALLATION INSTRUCTIONS

Item#2799-695/66A (New. 04/15/2022)
READ AND SAVE THESE INSTRUCTIONS
WARN I N G ! SH UT POWE R OF F AT FUS E OR CI RC U IT BRE AKE R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

MOUNTING THE FIXTURE (Fig.1) 1. Shut off power at the fuse box or circuit breaker and remove
the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on

Fig.1
Set# A-021 -Circular Strap

a clean area. Take care not to lose any small parts necessary

-Ground Screw

for installation.

-Mounting Screw*2

3. Thread screws (B) into pre-drilled holes on circular strap (G)

spaced same distance apart as holes in canopy (J) and

tighten with nuts (E). The length of screws (B) may be

adjusted if necessary.

4. Attach circular strap (G) to junction box (not included) using

mounting screws (D). The side of circular strap marked “GND”

must face out.

5. Run the wires through the central tube of canopy (J).

E

C

6. Connect fixture (F) to the central pipe of canopy (J). 7.Install

B

G

(3)three candelabra (T8) bulbs(not included) up to 40 watts each (not included) in accordance with the fixture

D

specification–DO NOT EXCEED THE MAXIMUM

WATTAGE RATING! (NE PAS DEPASSER LA

I

J

PUISSANCE NOMINALE MAXIMALE!).

8. Screw glass (I) onto fixture (F). Don’t over tighten. CONNECTING THE WIRES (Fig.2)

A

9. Connect the electrical wires as shown in Fig.2, making sure

that all wire connectors (C) are secured. If your junction box

has a ground wire (green or bare copper), connect the fixture’s

ground wire to it. Otherwise, connect the fixture’s ground wire

F

directly to the circular strap (G) using the green screw provided.

10. Tuck wire connectors neatly into the junction box.
FINISHING THE INSTALLATION (Fig.1) 11. Place canopy (J) over screws (B) and secure with finials (A).

Your installation is now complete. Return power to the

junction box and test the fixture.
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Fig.2

URE

FIXT WIRE SBlack or Smooth

USE ES

HO WIR B(Hlaoct)k

FIXTURE WIRES White or Ribbed

FIXTURE
WGrIeReEnSor Bare Copper (Ground)

WHIORUESSE White (Neutral)

HOUSE WIRES Green (Ground)

2799-695