B751 27 HP Petrol Engine
Product Information:
27 HP Petrol Engine – Loncin
This user manual provides instructions for installing the petrol
engine for the Logosol band sawmill.
The pack supplied includes:
- 01-00779 27 hp petrol engine (including electric start)
- Final saw head assembly, 27 hp Loncin
Product Usage Instructions:
Installation: Engine and Throttle Cable
- Wear protective gloves and handle the engine carefully when
placing it on the engine shelf. - Secure the engine on the engine shelf using the provided
fastening screws. - Mount the drive belt and gas cable on the sawmill following the
assembly instructions. - Refer to the sawmill manual’s setup sequence instructions to
complete the setup after assembly. - Fitting the exhaust deflector on the silencer:
- Install the engine on the engine shelf.
- Install the engine on the saw head before placing the saw head
on the rail. Use two people to lift the engine into place. - Thread the drive belt around the drive wheel and over the
tensioner. - Install the end of the wire in the throttle handle and thread
it into the casing. - Mount the handle on the handle tube.
- Remove the air filter cover, air filter, and unscrew the plate.
Thread the gas wire through the front cover. - Fit the throttle link on the wire retainer and lock the
assembly into position using the lock washer.
Mounting: Safety Switch & Electric Starter
- Install the safety hinge on the side of the cover where no
hinge is installed. Ensure that the cable output faces the middle
of the engine shelf. - Connect the safety switch to the engine as illustrated.
- To check the safety function, follow these steps:
- Open the cover.
- Turn the ignition key from the operator’s station to start the
engine. - If the engine starts with the cover open, switch off the engine
from the operator’s station. - Double-check the connection.
Safety Instructions:
Switch off the machine from the operator’s position before
working on the saw head.
The engine and its silencer become very hot during operation and
remain so after the engine has been shut down. Allow the engine and
silencer to cool before performing servicing or maintenance on the
machine.
USER MANUAL
ORIGINAL USER MANUAL.
Ref..no: 0458-395-0821
REV: 1
27 HP PETROL ENGINE
LONCIN
This manual describes installation of the petrol engine for the Logosol band sawmill.
Please see the user manual for your band sawmill for information on assembly, settings and safety instructions.
Read through the user manual carefully and make sure you understand its contents before using the saw.
EN
PACK SUPPLIED
01-00779 27 hp petrol engine (incl electric start)
FINAL SAW HEAD ASSEMBLY, 27 HP LONCIN
Read through all the set-up instructions before starting to set up, then follow the instructions step by step as you work.
1
Numbering for installation sequence
After assembly, follow the instructions under Setup sequence in the sawmill manual to complete setup before starting the machine.
2
WARNING! Heavy! Risk of injury.
WARNING! Risk of crushing injury.
Two people are always required to help with heavy lifting.
INSTALLATION: ENGINE AND THROTTLE CABLE
Wear protective gloves and handle the engine carefully when placing it down on the engine shelf.
The engine has to be installed on the engine shelf and secured using the fastening screws. The drive belt and the gas cable shall be mounted on the sawmill. Follow the assembly instructions and then go through the machine’s sequence of settings once assembly is complete.
1
Fitting the exhaust deflector on the silencer.
3 x M4x15
Install the engine on the engine shelf:
2
Install the engine on the saw head before
placing the saw head on the rail. Two people
are always required to help when the engine
is lifted into place. The illustration below
shows the hole pattern for installing the 27 hp
Loncin engine.
4 x M10x50
4 x M10
Top view: B1001, 27 hp Loncin
3
3
Thread the drive belt around the drive wheel
and over the tensioner.
1 x 9020-011-0091
4
Install the end of the wire in the
throttle handle, then thread it into
the casing.
1 x 01-00793
5
Mount the handle on the handle tube.
1 x M6x50
M6
M5 1 x M5x50
1 x M6
1 x M5
4
6
Remove the air filter cover, remove the air filter and unscrew the plate. Thread the gas
wire through the front cover.
7
Fit the throttle link on the cwire retainer,
then lock the assembly into position using
the lock washer.
8
· Hang the throttle link in the outer hole of the throttle (1).
· Clamp the wire into the front clamping bracket, closest to the front cover. NB! Attach it to the inside of the clamp bracket closest to the engine (2).
2 1
5
WARNING! Risk of serious injury.
The hinge switch for the machine has to be fitted before starting to use the machine.
Always switch off the machine from the operator’s position before working on the saw head.
WARNING! Risk of burn injuries. The engine and its silencer become very hot during operation and remain so after the engine has been shut down.
Allow the engine and the silencer to cool to cool before performing servicing or maintenance on the machine.
Now install the safety hinge on the side of the
9
cover where no hinge is installed. Note that
the cable output has to face the middle of the
engine shelf.
10 mm 12 mm
2 x M6x25 2 x M6x30 1 x 03-01997 1 x 03-02080
2 x 03-02182
M6x25 M6x30
10mm
12mm
6
MOUNTING: SAFETY SWITCH & ELECTRIC STARTER
10
Now connect the safety switch to the engine as illustrated.
How to check the safety function: Start by opening the cover. Turn the ignition key from the operator’s station to start the engine. The installation is correct if the engine does not start when the key is turned. Switch off the engine from the operator’s station if the engine starts with the cover open. Then double-check the connection.
Orange cable
Now connect the battery to the motor
11 according as illustrated.
2 x M6x20 2 x M6
Black cable
Red cable
The battery is placed in the protective box and secured using the strap as illustrated.
7
12
Install the shelf for the gas tank using the sawmill’s existing screws.
13
Place the gas tank on the shelf and fasten it with the tensioning
strap. Attach the oil hose to the
tank and engine.
Before start-up, top up with oil.
8
WARNING! Risk of serious injury.
Before adjusting the throttle cable tension on the engine: Turn the ignition to OFF and close the fuel valve.
Always start the machine from the operator’s station. Always turn off the machine before adjusting the tension of the throttle cable on the engine side.
WARNING! Risk of burn injuries. The engine and its silencer become very hot during operation and remain so after the engine has been shut down.
Allow the engine and the silencer to cool to cool before performing servicing or maintenance on the machine.
14
THROTTLE ADJUSTMENT
· Start by adjusting the throttle cable at the throttle handle so that you have equal adjustment travel in both directions (1).
· Attach the other end of the wire housing to the clamp on the engine (2).
· Screw the wire into the nipple (3). Make sure that the throttle is in the neutral/unaffected position when doing this.
· Check that you have 1 to 3 mm of play in the throttle handle, and that the wire moves freely. Adjust the wire tension at the throttle handle (1), if necessary
· Start the engine and check that it is idling and that the saw blade does not move while the throttle handle is in idle position. Adjust the cable tension at the throttle handle (1), if necessary
· Secure the adjustment using the counter nuts (4)
· Cut off the wire that is left over, save about 30 mm (5).
4 1
30 mm
2
5
3 9
Well done!
Now you have finished installing the engine, go back to the manual for your band sawmill and carry on with the setup sequence, starting at the point as indicated in the instructions below.
ADJUSTMENT SEQUENCE
Read through all the set-up instructions before starting to set up, then follow the instructions step by step as you work.
IMPORTANT! It is important to adjust the saw head before starting to ensure satisfactory sawing and the correct functioning of the sawmill. Carefully follow the adjustment sequence! Certain adjustments affect other machine settings.
Fiskaregatan 2, SE-871 33 Härnösand, Sweden +46 611-182 85 | [email protected] | www.logosol.com
Portable Sawmills and Woodworking Machinery | LOGOSOL | LOGOSOL
