Generation Lighting Fulton 3 And 5 Light Chandelier Installation Guide

Fulton 3 and 5 Light Chandelier

Installation Instructions for Fullton 3 and 5 Light
Chandelier

Product: CHANDELIER FULLTON_CHAND 3164203, 3164205 1.0

General Product Information:

These fixtures are intended to be installed utilizing NEC
compliant junction boxes. This product is safety listed for damp
locations. This instruction shows a typical installation.

CAUTION – RISK OF FIRE: This product must be
installed in accordance with the applicable installation code by a
person familiar with the construction and operation of the product
and the hazards involved. SAVE THESE INSTRUCTIONS!

7400 Linder Ave., Skokie, IL 60077 T 847.410.4400 | F
847.410.4500
www.generationlighting.com

Product Usage Instructions:

1. Screw the nipple to the bottom of the fixture, then place the
   bottom cup over the nipple and secure it in place by screwing the
   cover onto the nipple.
2. Feed the fixture wires through the threaded pipe, pipe cover,
   and washer, then screw the threaded pipe to the top of the coupler.
   Let the pipe cover and washer slide over the threaded pipe.
3. Screw the half ball to the stem which will be on top.
4. Determine the wanted height or look of the fixture with the
   provided stems, then assemble them by screwing them together.
5. Feed the fixture wires through the stem assembly, then screw
   the stem assembly onto the threaded pipe.
6. Feed the fixture wires through the collar nut, canopy, and the
   half ball assembly, then screw it onto the stem assembly.
7. Align and secure the mounting plate to the junction box, then
   slide the half ball assembly onto the mounting plate.
8. Connect the fixture to a suitable ground in accordance with
   local electrical codes.
9. Connect the white fixture wire (square and/or rigid) to the
   neutral power line wire with a wire nut.
10. Connect the black fixture wire (round and/or smooth) to the hot
    power line wire with a wire nut.
11. Neatly place all the wires into the junction box, place the
    canopy onto the mounting plate, and secure it in place by screwing
    the collar nut tightly onto the mounting plate.
12. Screw the lamps into the sockets. Refer to the label on the
    socket for Max Wattage Information.

Installation Instructions for
Fullton 3 and 5 Light Chandelier
CHANDELIER

FULLTON_CHAND
3164203, 3164205 1.0

GENERAL PRODUCT INFORMATION:
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations.
This instruction shows a typical installation.

CAUTION – RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Use minimum 90°c supply conductors.
SAVE THESE INSTRUCTIONS!

©2022 Visual Comfort & Co., L.L.C. All rights reserved. The Visual Comfort & Co. logo is a registered trademark of Visual Comfort & Co. Visual Comfort & Co. reserves the right to change specifications for product improvements without notification.

7400 Linder Ave., Skokie, IL 60077 T 847.410.4400 | F 847.410.4500
www.generationlighting.com

Install the Fixture
1A

JUNCTION BOX
10 HALF BALL

MOUNTING PLATE

8 9
CANOPY 3
COLLAR NUT 6

4 STEM
4

2 5

WASHER

THREADED PIPE

PIPE COVER 12

COUPLER 2

FIXTURE BOTTOM CUP

NIPPLE COVER 1

LAMP

1 Screw the nipple to the bottom of the fixture, then place the bottom cup over the nipple and secure it in place by screwing the cover onto the nipple.
2 Feed the fixture wires through the threaded pipe, pipe cover, and washer, then screw the threaded pipe to the top of the coupler. Let the pipe cover and washer slide over the threaded pipe.
3 Screw the half ball to the stem which will be on top. 4 Determine the wanted height or look of the fixture with the provided stems, then assemble them by screwing them together.
5 Feed the fixture wires through the stem assembly, then screw the stem assembly onto the threaded pipe.
6 Feed the fixture wires through the collar nut, canopy, and the half ball assembly, then screw it onto the stem assembly.
7 Align and secure the mounting plate to the junction box, then slide the half ball assembly onto the mounting plate. 8 Connect the fixture to a suitable ground in accordance with local electrical codes.
9 Connect the white fixture wire (square and/or rigid) to the neutral power line wire with a wire nut. 10 Connect the black fixture wire (round and/or smooth) to the hot power line wire with a wire nut. 11 Neatly place all the wires into the junction box, place the canopy onto the mounting plate, and secure it in place by screwing the collar nut
tightly onto the mounting plate. 12 Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage Information.

2

References

• Generation Lighting - Our Collections