HG8911 Modern 9 Light Black and Brown Finish Chandelier
Product Information
The product is a ceiling light with a canopy installation. It
comes with a wire connection diagram to ensure safe installation.
The light bulb used is E12 and can hold up to 9 bulbs with a
maximum rating of 60W and a rated voltage of 110-130V/60Hz. The
product size measures 60.2 x 39.4 x 19.6 cm and comes with a buckle
to adjust the chain length.
Product Usage Instructions
- Before installation, make sure that the power supply is turned
off and remains off until installation is complete. - Attach the Crossbar(B) to the existing electrical box(A) using
the two crossbar screws(C) which are not supplied and should
already be in your box. - Slide the canopy loop nut lock(F) back up over the canopy
loop(D), pass the canopy loop(D) through canopy(E), connect with
the threaded pipe underside of the crossbar. - Pass the main wire(J) and ground wire(H) through the loop(I),
the chain(G), the canopy loop nut lock(F), the canopy(E), the
canopy loop (D) and the crossbar(B) until the end of the main
wire(J) reaches the electrical box(A) where you can make the
appropriate connections. Be sure when connecting the wire use
electrician approved junction caps(K). - Stow the excess wire in the electrical box(A).
- Raise the canopy(E) and canopy loop nut lock(F), attach
canopy(E) to ceiling, slide canopy loop nut lock(F) over canopy
loop(D) and hold the canopy(E). - Buckle is used to connect the chain and loop or adjust the
length of chain. - Install the light bulb by following the manufacturer’s
instructions.
CANOPY INSTALLATION INSTRUCTIONS
WIRE CONNECTION DIAGRAM
Wires meet safety standards are recommended to connect the supply circuit.
CAUTION: Risk of fire
Light Bulb
E12
CANOPY INSTALLATION INSTRUCTIONS Please read all instructions carefully.Before you proceed to install,make sure that the power supply is turned off and remainsoff until installation is complete. Please not that each part has been assigned a letter. Please proceed in an alphabetical order.
A. Existing Electrical Box B. Crossbar
C. Crossbar Screws
D.Canopy Loop
E. Canopy
F. Canopy Loop Nut lock
G. Chain
H. Ground Wire
I. Loop
J. Wire
K. Junction Caps
Attach the Crossbar(B) to the existing
electrical box(A) using the two crossbar screws
(C) which are not supplied and should already be in your box.
Slide the canopy loop nut lock(F) back up over the canopy loop(D),pass the canopy loop(D) through canopy(E),connect with the threaded pipe underside of the crossbar.
Pass the main wire(J) and ground wire(H) through the loop(I),the chain(G),the canopy loop nut lock(F),the canopy(E),the canopy loop
(D) and the crossbar(B) until the end of the main wire(J) reaches the electrical box(A) where you can make the appropriate connections. Be sure when connecting the wire use electrician approved junction caps(K).Stow the
excess wire in the electrical box(A).Raise the
canopy(E) and canopy loop nut lock(F),attach canopy(E) to ceiling,slide canopy loop nut
lock(F) over canopy loop(D) and hold the
canopy(E).
Buckle is used to connect the chain and loop or adjust the length of chain.
USER MANUAL FOR MODEL# HG8911
Light Bulb:E12 light:E12*9 ( Rated 110-130V/60Hz,bulb 60W maximum.)
1
Please note: The parts in this table are completely unassembled, for illustrative purpose. In the actual product that you receive, some parts are assembled and attached together.
NO.
1
2 3
4
5 6
Products list
Picture
Quantity
1 PCS
1 PCS 4 PCS 1 PCS
83 PCS 83 PCS
2
Assembly and Installation Steps
1: Used two screws lock on the ceiling tightly to fix the light.
2:Lock together.
4:The lamp body with samall chains on the chassis.
5: Install the bulb.
6:The steps of hanging crystals.
60.2 19.6
9.1
39.4 1.2
Product Size
5.1″
15 19.3
24 3
