342554 Fairwinds Post Light
Product Information – Fairwinds Post Light – 342554
The Fairwinds Post Light – 342554 is a handcrafted lighting
fixture made by Modern American Blacksmiths at Castleton, Vermont
USA. It is sold by Hubbardtonforge.com. The product comes with
component parts including a Post / Pier Mount, J Bolt (4), Flat
Washer (4), Split Washer (4), Hex Nut (4), Cover Cap, Set Screw,
Fixture, Bulb (not included), Socket, Glass, Cap, Rubber Washer (2)
and Threaded Stud. The product should be installed properly to
avoid any personal injury or property damage. It is recommended to
be installed by a licensed electrician in accordance with
applicable installation code(s). The maximum wattage noted on the
fixture should not be exceeded and only recommended bulbs should be
used with the fixture.
Product Usage Instructions – Fairwinds Post Light – 342554
Before installation, make sure that the power is off at the main
breaker box. Follow the steps below to install and use the
Fairwinds Post Light:
- Run appropriate wiring to the site of the fixture, leaving
enough excess wire to reach the top of the post, plus 12
inches. - Pour flat and level concrete base with wiring emerging at the
center. Insert J bolts (B) so approximately 1 of the bolts are
exposed above the concrete. Position J bolts according to the
template on the last page of these instructions. Allow concrete to
cure before installing fixture. - Position post (A) over J bolts (B), feeding supply wire up
though the post and secure using flat washers (C), split washers
(D) and hex nuts (E). - Place optional cover cap (sold separately) (F) over post (A) to
conceal mounting hardware. - Connect fixture wires to supply wires using appropriate wire
connectors (not provided), black to black (or smooth), white to
white (or ribbed) and tinned copper or green to tinned copper or
green. Make sure wire connectors are twisted on securely and no
bare wire is exposed. - Place fixture (H) onto post (A), carefully tucking all wiring
down into post and making sure no wires are pinched between the
post and the fixture. Secure with set screw (G). - Install bulb (not included) (I) into socket (J).
- Slide glass (K) onto fixture (H) and allow it to rest fully on
fixture (H). - Slip glass cover cap (O) onto threaded stud (N) until it rests
on top of glass (K). - Install rubber washers (M) onto threaded stud (N).
- Thread cap (L) onto threaded stud (N) until snug. Be careful
not to over tighten. - Restore electricity at main breaker.
G36
ASSEMBLY & INSTALLATION INSTRUCTIONS
Fairwinds Post Light – 342554
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
52421
1 OF 5
G36
ASSEMBLY & INSTALLATION INSTRUCTIONS
Fairwinds Post Light – 342554
Component Parts
NOTE: Items A through F are options sold and shipped separately to allow for various site situations and shown here for reference during installation as applicable
A Post / Pier Mount – Optional and sold separately
B J Bolt (4) – Included with optional post/pier mount
C Flat Washer (4) – Included with optional post/pier mount
D Split Washer (4) – Included with optional post/pier mount
E Hex Nut (4) – Included with optional post/pier mount
F Cover Cap – Optional and sold separately
G Set Screw
H Fixture
I
Bulb (not included)
J Socket
K Glass
L Cap
M Rubber Washer (2)
N Threaded Stud
O Glass Cover Cap
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
52421
2 OF 5
G36
ASSEMBLY & INSTALLATION INSTRUCTIONS
Fairwinds Post Light – 342554
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.* Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Install Canopy (Figure 1 – on following page)
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION. NOTE: Fixture, Post and Cover Cap each sold separately. 1. Run appropriate wiring to the site of the fixture, leaving enough excess wire to reach the top of the post, plus 12
inches. 2. Pour flat and level concrete base with wiring emerging at the center. Insert J bolts (B) so approximately 1″ of
the bolts are exposed above the concrete. Position J bolts according to the template on the last page of these instructions. Allow concrete to cure before installing fixture.
INSTALLATION: NOTE: Post may be cut to desired height before installation. 3. Position post (A) over J bolts (B), feeding supply wire up though the post and secure using flat washers (C), split
washers (D) and hex nuts (E). 4. Place optional cover cap (sold separately) (F) over post (A) to conceal mounting hardware. 5. Connect fixture wires to supply wires using appropriate wire connectors (not provided), black to black (or
smooth), white to white (or ribbed) and tinned copper or green to tinned copper or green.
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY AND NO BARE WIRE IS EXPOSED.
6. Place fixture (H) onto post (A), carefully tucking all wiring down into post and making sure no wires are pinched between the post and the fixture. Secure with set screw (G).
7. Carefully unpack glass (K). 8. Install bulb (not included) (I) into socket (J). 9. Slide glass (K) onto fixture (H) and allow it to rest fully on fixture (H). 10. Slip glass cover cap (O) onto threaded stud (N) until it rests on top of glass (K). 11. Install rubber washers (M) onto threaded stud (N). 12. Thread cap (L) onto threaded stud (N) until snug. Be careful to not over tighten. 13. Restore electricity at main breaker.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
52421
3 OF 5
G36
ASSEMBLY & INSTALLATION INSTRUCTIONS
Fairwinds Post Light – 342554
L M O K
(Figure 1)
I N
J H
G A
F E D C B
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
52421
4 OF 5
G36
ASSEMBLY & INSTALLATION INSTRUCTIONS
Fairwinds Post Light – 342554
USE THIS TEMPLATE TO POSITION J BOLTS AND WIREWAY IN CONCRETE SLAB PRIOR TO INSTALLING OUTDOOR POST MOUNTED LIGHTING FIXTURE.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
52421
5 OF 5
