13799 Bliss Outdoor Garden Bollard Light
Product Information
- Fitting/Replacing Bulbs: Always use the
correct type and wattage bulb. Do not exceed the wattage stated or
use a different shape bulb from that indicated on the fitting. When
changing a bulb, always switch off at the mains and allow the old
bulb to cool down before handling. The entire unit gets hot whilst
on for a period of time. Dispose of used bulbs carefully and
responsibly. - Technical Data:
- Supply Voltage: 220-240 V~, 50 Hz
- Bulb Type: Max. 10.5W LED E27 (required)
- Conformity: Conforms to all relevant UKCA
Directive requirements and EC Directive requirements. - Class: Class 1 product, must be earthed.
- Waste Disposal: Waste electrical products
should not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or local
store for recycling advice. - Dimmable: This product is suitable for
dimming. - IP Rating: IP44
- IK Rating: IK05
- Care and Safety: We recommend cleaning with a
soft dry cloth. Do not use solvents or abrasive cleaners as these
could damage the finish. For your safety, always switch off the
power supply before changing lightbulbs or cleaning.
Product Usage Instructions
- When fitting or replacing bulbs:
- Use the correct type and wattage bulb.
- Do not exceed the stated wattage or use a different shape bulb
than indicated on the fitting.
- When changing a bulb:
- Switch off the power supply at the mains.
- Allow the old bulb to cool down before handling.
- Dispose of used bulbs carefully and responsibly.
- To wire the product:
- Identify the wiring from your existing light fitting.
- Pull the mains wire through the hole and connect it to the
quick fit connection block inside the product as follows:- SUPPLY NEUTRAL EARTH (GREEN/YELLOW)
- SWITCHED LIVE
- LIGHT FITTING BLUE (N)
- GREEN/YELLOW BROWN (L)
- Ensure that you have correctly identified the wires, the
connections are tight, and no loose strands have been left out of
the connection block.
Please refer to the wiring diagram provided for additional
guidance.
Fitting/Replacing Bulbs
Always use the correct type and wattage bulb. Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting.
When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling. The entire unit gets hot whilst on for a period of time.
Dispose of used bulbs carefully and responsibly.
Max. 10.5W LED E27
Technical data
Supply Voltage:
220-240 V~, 50 Hz
Bulb Type:
Max. 10.5W LED E27 (required)
Conformity with all relevant UKCA Directive requirements.
Conformity with all relevant EC Directive requirements.
This is a Class 1 product and must be earthed.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
This product is suitable for dimming.
IP44
This product is rated at IP44.
IK05
This product is rated at IK05.
Care and Safety We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. For your safety, always switch off the power supply before changing lightbulbs, or cleaning.
V4 26/12/2021 UK Manufacturer: BH17 7BY EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
Instruction manual
BLISS
13799, 92531
13799
92531
www.saxbylighting.com
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.
Warning This is a Class 1 product and must be earthed. Please read these instructions carefully before commencing any work. This unit must be fitted by a competent and qualified electrician. Install in accordance with the IEE Wiring regulations and current Building Regulations. Check the pack and make sure you have all the parts listed. To prevent electrocution switch off at the mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you any doubt please consult a qualified electrician. This light fitting should be connected to a circuit with a 30mA RCD fitted. If replacing an existing fitting, make a careful note of the connections. This product is not suitable for location in or near a marine or sea environment. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
Layout This fitting must be mounted on either a concrete surface or a paving slab that has been concreted in position. Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between each light fitting. Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged. We recommend that your use H05RN-F specification cable (not supplied) which is an outdoor grade, rubber sheathed cable. The cable can be wired into an IP67 (or higher rated) external terminal block (recommended terminal block Ref. 90131/90132). This must be carried out by a competent and qualified electrician. The mains supply cable must have a minimum cross section area of 1.0mm2 Cables must be protected using suitable conduit or plastic trunking.
Installation Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires. Note that the switch is turned off before installation. Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product. After deciding the layout of the light fittings ensure that the cables are long enough to connect to desired positions. · Using base plate as a template, mark the fixing holes onto the mounting surface. · Drill holes to the necessary size and depth – taking care not to damage any concealed pipes or wiring below the
mounting surface. · We recommend fitting this product with screws (A) which are suitable for use on most surfaces, however alternative
fixings may be required. · Push the raw plugs (B) into the mounting holes as shown. · Pull terminal block (C) from inside of tube. · Unscrew the 4 screws which attach the black box to the spacing strip. Open the black box and pull out the terminal block. · Connect the Cables as the wiring diagram.
See Wiring Diagram
Wiring
Having correctly identified the wiring from your existing light fitting, pull the mains wire through the hole and connect to the quick fit connection block inside the product in the following way:
SUPPLY NEUTRAL EARTH (GREEN/YELLOW) SWITCHED LIVE
LIGHT FITTING BLUE (N)
GREEN/YELLOW BROWN (L)
Check that…
You have correctly identified the wires. The connections are tight. No loose strands have been left out of the connection block.
Saxby Lighting - Commercial and Domestic Lighting Supplier
