Saxby Lighting 13914 Palin Garden Spike Bollard Post Top Garden Light Instructions

• Clean the product with a soft dry cloth.
• Avoid using abrasive materials, solvents, or abrasive cleaners
  as they may damage the finish.

• Do not dispose of waste electrical products with household
  waste.
• Check with your Local Authority or retailer for recycling
  advice and facilities.

• Always switch off the power supply before cleaning to ensure
  safety.
• This fitting must not be used without the glass shade in
  place.

• This unit must be fitted by a competent and qualified
  electrician.
• Install in accordance with IEE Wiring regulations and current
  Building Regulations.
• Switch off the mains supply before installing or maintaining
  the fitting to prevent electrocution.
• The light fitting should be connected to a fused circuit and a
  30mA RCD.
• Ensure that other persons cannot restore the electrical supply
  without your knowledge.
• If in doubt, consult a qualified electrician.

• This product is not suitable for location in or near a marine
  environment.
• The entire unit can become hot while in use for a period of
  time.
• An approved outdoor rated plug and socket or an approved
  outdoor rated external terminal block may be required depending on
  the location.
• Position cables and connector blocks away from areas where they
  may be at risk of being cut, trapped, or damaged.
• Underground cables must be protected using suitable conduit or
  plastic trunking.
• If the external flexible cable or cord of the lamp is damaged,
  it must be returned to the service agent for repair.

Fitting/replacing bulbs (Max. 7W LED GU10)
When changing a bulb, always switch off at the mains and allow the bulb to cool before handling. Dispose of used bulbs carefully. Use a soft cloth to handle bulbs, avoid directly touching the bulbs as this will shorten their life. Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting. Check with your retailer re bulb dimming capability before purchasing replacement bulbs. 7W LED GU10 1. Unscrew the bezel 2. Remove the old bulb by turning anti-clockwise. 3. Insert new bulb. 4. Replace the bezel ensuring that it is tightly secured.
Care and Cleaning
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish. Do not use solvents or abrasive cleaners as these could damage the finish.
For 13797 and 13914, in normal circumstances, stainless steel is very resistant to corrosion. It does however require maintenance to preserve the high quality appearance. Wash the product with warm soapy water, removing all surface deposits. Rinse with clear water and with a soft cloth, wipe dry. In some cases, surface corrosion may arise after installation. This is normally caused by tiny iron particles left behind after the brushing process when finishing. Wash and dry as detailed above. Then with a soft cloth soaked with a protective oil, wipe all over. However if the product is subject to extreme environmental conditions such as marine locations, industrial pollution and acid rain these maintenance procedures should be carried out around four times a year. For severe corrosion, non-abrasive cream cleaners or proprietary stainless steel cleaners should be used to remove the corrosion. Wash and dry as detailed above. Then with a soft cloth soaked with a protective oil, wipe all over. Do not clean the units with a pressure washer.
Recycling advice
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Safety information
For your safety, always power switch off the supply before cleaning.
This LED’s are protected by the glass shade. The shade part must be replaced immediately should it Replace Cracked Shade become cracked or damaged. This fitting must not be used without the glass shade in place.

UK Manufacturer: BH17 7BY EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
www.saxbylighting.com

V2 08/01/2022 Saxby Lighting

Instruction leaflet
Palin Spike
13797, 13914, 75438

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Warning

This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
Always use the correct type and wattage bulb. Never exceed the wattage stated.
This product is suitable for dimming when used with a dimmable bulb.

When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling. Dispose of used bulbs carefully and responsibly.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
This product is rated at IP44.
This product is not suitable for location in or near a marine environment.
Please note: entire unit gets hot whilst on for a period of time.
This light fitting should be connected to a 30mA RCD.
This product may require the use of a outdoor rated connector block.
If the external flexible cable or cord of this lamp is damaged the lamp must be returned to the service agent for repair.

Specification

Voltage: Lamp: IP rating:

220-240V~ 50Hz 1 x Max. 7W LED GU10 44

Layout

on the location, an approved outdoor rated plug and socket may be required. Alternatively an approved outdoor rated external terminal block may be used.
cause a hazard. Position cables and connector block away from areas where they may be at risk from being cut, trapped or damaged.

underground must be protected using suitable conduit or plastic trunking.
spike into, and can support the luminaire. Do not install in very wet or boggy areas.

Wiring
Plug Wiring
or in an approved outdoor rated enclosure.
supply.
fitted with a 3 amp fuse. Should the fuse require replacement, it must be replaced with a fuse rated at 3 amp and approved to BS1362.
coloured in accordance with the following code: Blue ­ Neutral Green / Yellow – Earth Brown ­ Live

BLUE Neutral

GREEN / YELLOW Earth
E L

N
Cord Clamp

BROWN Live
Fuse 3 Amps

Wiring
If not fitting to a plug then the product must be wired to an approved outdoor rated terminal block.
SUPPLY NEUTRAL EARTH (GREEN/YELLOW) SWITCHED LIVE

Having correctly identified the wiring from your existing light fitting, connect to the approved outdoor rated external terminal block in the following way:
LIGHT FITTING
BLUE (N)
GREEN/YELLOW
BROWN (L)

Check that…
You have correctly identified the wires The connections are tight No loose strands have been left out of the connection block.

Ensure that all cord grips are tightly secured. Ensure that all seals are re-fitted correctly.

Commissioning

spike into, and can support the luminaire. Do not install in very wet or boggy areas. Push the spike into the ground.

light is now ready for use.

References

• Saxby Lighting - Commercial and Domestic Lighting Supplier