V I V O Mount-vp06b Black Projector Ceiling And Wall Mount Instruction Manual (+ PDF)

Home » Blog » V I V O Mount-vp06b Black Projector Ceiling And Wall Mount Instruction Manual

Contents hide

1 MOUNT-VP06B Black Projector Ceiling and Wall Mount

2 Product Information: Black Projector Ceiling and Wall Mount

3 Product Usage Instructions:

3.1 Documents / Resources

3.1.1 References

MOUNT-VP06B Black Projector Ceiling and Wall Mount

Product Information: Black Projector Ceiling and Wall
Mount

The Black Projector Ceiling and Wall Mount is a mounting
solution for projectors that can be used both on ceilings and
walls. It comes with a ceiling plate, pole, brackets, screws,
washers, and anchors. The mount can support up to 44lbs (19.96kg)
of weight and is not suitable for children under 3 years of age due
to small parts.

Product Usage Instructions:

Route the cables through the telescopic pole (B) and the
ceiling plate (A). Attach the ceiling plate to the telescopic pole
using M6x10 screws (M-B) and D6 washers (M-J) with the large Allen
wrench (M-L).
For wood ceiling installation, position the ceiling plate
against the ceiling and mark drill locations with a pencil. Use a
stud finder for wood beam ceilings. Drill 2.2 (55mm) deep holes
using a 3/16 (4.5mm) drill bit. Mount the ceiling plate using
screws (W-A) and washers (W-C). For concrete ceiling installation,
position the ceiling plate against the ceiling and mark drill
locations with a pencil. Drill 2.4 (60mm) deep holes using a 3/8
(10mm) drill bit. Press concrete anchors (W-B) into holes. Mount
the ceiling plate using screws (W-A) and washers (W-C).
Install the projector mounting bracket (D) to the projector
using appropriate screws (M-C, M-D, M-E) and washers (M-F, M-G,
M-H). Swap appropriate arm extensions with alternate extensions
(M-M) if your projector has uneven mounting holes. If your
projector has only three mounting holes, leave one mounting arm
unused.
Hang the projector with mounting bracket over the mounting
bracket. Secure using x2 M5x10 screws (M-A), D5 washers (M-H), and
plastic D5 washers (M-I) with the small Allen wrench (M-K).
Adjust the tilt angle and secure with the small Allen wrench
(M-K).
Attach the mounting bracket (C) to the telescopic pole in the
alternate position using x4 M5x10 screws (M-A) and x4 D5 washers
(M-H) with the small Allen wrench (M-K).

Note: Do not install into drywall alone. Verify your ceiling
construction and use wood studs to mount. If unsure, contact
vivo-us.com, email at [email protected], or call at 309-278-5303.
Some hardware included may not be used.

View Fullscreen

Black Projector Ceiling and Wall Mount
Instruction Manual

SKU: MOUNT-VP06B
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/mount-vp06b
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

[email protected]

www.vivo-us.com Chat live with an agent!

309-278-5303

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS

A (x1) Ceiling Plate

B (x1) Pole

M-A (x6) M5x10

M-B (x4) M6x10

C (x1) Bracket
M-C (x4) M5x8

D (x1) Bracket

E (x1) Cover

M-D (x4) M4x8

M-E (x4) M3x8

M-F (x4) D3 Washer

M-G (x4) D4 Washer

M-H (x10) D5 Washer

M-I (x2) D5 Washer

M-J (x4) D6 Washer

M-K (x1) Allen Wrench

M-L (x1) Allen Wrench

M-M (x2) Arm Extension

W-A (x4) Screw

W-B (x4) Anchor

W-C (x4) Washer

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR CEILING CONSTRUCTION. USE WOOD STUDS TO MOUNT. We include mounting for brick and concrete. If unsure, please contact us at vivo-us.com, email at [email protected], or call us at 309-278-5303.

TOOLS NEEDED

Drill

Phillips

Screwdriver

DO NOT EXCEED WEIGHT CAPACITY.
44lbs Failure to do so may result in serious injury. (19.96kg)

ASSEMBLY STEPS
STEP 1
Route cables through telescopic pole (B). Route cables through ceiling plate (A). Attach ceiling plate to telescopic pole using M6x10 screws (M-B) and D6 washers (M-J), and tighten with large Allen wrench (M-L). Attach mounting bracket (C) to telescopic pole using x4 M5x10 screws (M-A) and x4 D5 washers (M-H), and tighten with small Allen wrench (M-K).

M- B M- J M- L

STEP 2
OPTION A: Wood Ceiling Installation Position ceiling plate against ceiling and mark drill locations with a pencil. Use of a stud finder is recommended with wood beam ceilings. Drill 2.2″ (55mm) deep holes using a 3/16″ (4.5mm) drill bit. Mount ceiling plate using screws (W-A) and washers (W-C).
W- C W- A
M- A M- H
M- K
OPTION B: Concrete Ceiling Installation Position ceiling plate against ceiling and mark drill locations with a pencil. Drill 2.4″ (60mm) deep holes using a 3/8″ (10mm) drill bit. Press concrete anchors (W-B) into holes. Mount ceiling plate using screws (W-A) and washers (W-C). Please note, anchors are designed for use in concrete and are not suitable for use in drywall.
W- B W- C W- A
4

STEP 3
Install projector mounting bracket (D) to projector using appropriate screws (M-C, M-D, M-E) and washers (M-F, M-G, M-H). For projectors with uneven mounting holes, swap appropriate arm extensions with alternate extensions (M-M). Please note, if your projector has only three mounting holes, simply leave one mounting arm unused.

M- M

M-C/M-D/M- E M-F/M-G/M- H

STEP 4
Hang projector with mounting bracket over mounting bracket. Secure using x2 M5x10 screws (M-A), D5 washers (M-H) and plastic D5 washers (M-I) with small Allen wrench (M-K).

M- L

M- A M- H
M- I

M- I M- H
M- A M- K

STEP 5
Adjust tilt angle and secure with small Allen wrench (M-K).
M- K

+8° -8°
STEP 6
Attach mounting bracket (C) to telescopic pole in alternate position using x4 M5x10 screws (M-A) and x4 D5 washers (M-H), and tighten with small Allen wrench (M-K).

M- A M- H
M- K
STEP 7
Brick/Concrete Wall Installation: Position ceiling plate against wall and mark drill locations with a pencil. Drill 2.4″ (60mm) deep holes using a 3/8″ (10mm) drill bit. Press concrete anchors (W-B) into holes. Mount ceiling plate using screws (W-A) and washers (W-C).

W- C W- A

W- B

STEP 8
Install projector mounting bracket (D) to projector using appropriate screws (M-C, M-D, M-E) and washers (M-F, M-G, M-H). For projectors M-M with uneven mounting holes, swap appropriate arm extensions with alternate extensions (M-M). Please note, if your projector has only three mounting holes, simply leave one mounting arm unused.

M-C/M-D/M- E M-F/M-G/M- H

STEP 9
Hang projector with mounting bracket over mounting bracket. Secure using x2 M5x10 screws (M-A), D5 washers (M-H) and plastic D5 washers (M-I) with small Allen wrench (M-K).

M- H M- A M- I

M- I M- H
M- A M- K

STEP 10
Adjust tilt angle and secure with small Allen wrench (M-K).
M- K -15° ~ 15°
+8° -8 ° 7

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

LAST UPDATED: 08/04/2022 REV1.1

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303

AVG. RESOLUTION TIME (within office hrs): 5M 4S

www.vivo-us.com
Chat live with an agent!

AVG. RESOLUTION TIME (within office hrs): < 15 M

[email protected]

AVG. RESPONSE TIME (within office hrs): 1HR 8M – 23% within < 15m – 38% within < 30m – 61% within < 1hr – 83% within < 2hr – 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com