Contents hide

2 Product Information: TDS 75 / TDS 100 / TDS 120 Electric Heater

TDS 75 Electric Heater Fan

Product Information: TDS 75 / TDS 100 / TDS 120 Electric
Heater

The TDS 75 / TDS 100 / TDS 120 Electric Heater is intended for
heating closed rooms while adhering to the technical data. The
device is suitable for heating the air in:

rooms that are dry or damp
rooms with electrical equipment in damp areas

The device is not intended for outdoor use or for use in
environments with a risk of explosion.

Symbols Used in the Manual

The following symbols are used in the manual:

Warning of electrical voltage: This symbol
indicates dangers to the life and health of persons due to
electrical voltage.
Warning of hot surface: This symbol indicates
dangers to the life and health of persons due to hot surface.
Warning: This signal word indicates a hazard
with an average risk level which, if not avoided, can result in
serious injury or death.
Caution: This signal word indicates a hazard
with a low risk level which, if not avoided, can result in minor or
moderate injury.
Note: This signal word indicates important
information (e.g. material damage), but does not indicate
hazards.
Info: Information marked with this symbol
helps you to carry out your tasks quickly and safely.
Follow the manual: Information marked with
this symbol indicates that the instructions must be observed.

Safety Precautions

Before starting or using the device, read the manual carefully.
Always store the manual in the immediate vicinity of the device or
its site of use. The following safety precautions must be
observed:

Do not use the device outdoors or in environments with a risk
of explosion.
Only use the device for heating closed rooms while adhering to
the technical data.
Do not cover the heater with objects like towels or clothes to
avoid overheating and fire hazards.
Work on the electrical components must only be carried out by
an authorized specialist company.
Remove the mains plug from the mains socket before any work on
the device.
Do not touch the mains plug with wet or damp hands. Hold onto
the mains plug while pulling the power cable out of the mains
socket.
Do not use this heating device in immediate proximity to
bathtubs, showers, or swimming pools to avoid the risk of electric
shock if the heating device comes into contact with water.
Parts of this appliance can become very hot and cause burns.
Particular attention is to be paid when there are children or
vulnerable persons present.
Only use the device as intended to avoid risks of burning and
electric shock.
Observe the personnel qualifications to avoid dangers that can
occur at the device when it is used by untrained people in an
unprofessional or improper way.

Product Usage Instructions

Follow these instructions to use the TDS 75 / TDS 100 / TDS 120
Electric Heater:

Place the device in a closed room while adhering to the
technical data.
Do not cover the heater with objects like towels or clothes to
avoid overheating and fire hazards.
Plug the device into a mains socket.
Turn on the device using the power button or switch.
Adjust the temperature and fan speed as desired using the
controls.
When not in use, turn off the device and unplug it from the
mains socket.

If you need to perform maintenance tasks that require the
housing to be opened, contact a specialist electrical company or
Trotec for assistance.

View Fullscreen

TDS 75 / TDS 100 / TDS 120
EN
ORIGINAL INSTRUCTIONS ELECTRIC HEATER

TRT-BA-TDS75-TDS100-TDS120-TC210914TTRT01-010-EN

Table of contents
Notes regarding the instructions …………………………………… 2 Safety …………………………………………………………………………. 2 Information about the device………………………………………… 5 Transport and storage………………………………………………….. 7 Assembly and start-up…………………………………………………. 7 Operation ……………………………………………………………………. 8 Errors and faults………………………………………………………….. 9 Maintenance ……………………………………………………………… 10 Technical annex…………………………………………………………. 11 Disposal ……………………………………………………………………. 16 Declaration of conformity …………………………………………… 16

You can download the current version of the instructions via the following link:
TDS 75
https://hub.trotec.com/?id=39786
TDS 100
https://hub.trotec.com/?id=42382

Notes regarding the instructions

TDS 120

Symbols
Warning of electrical voltage This symbol indicates dangers to the life and health of persons due to electrical voltage.
Warning of hot surface This symbol indicates dangers to the life and health of persons due to hot surface.
Warning This signal word indicates a hazard with an average risk level which, if not avoided, can result in serious injury or death.
Caution This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury.
Note This signal word indicates important information (e.g. material damage), but does not indicate hazards.
Info Information marked with this symbol helps you to carry out your tasks quickly and safely.
Follow the manual Information marked with this symbol indicates that the instructions must be observed.

https://hub.trotec.com/?id=42383
Safety
Read this manual carefully before starting or using the device. Always store the manual in the immediate vicinity of the device or its site of use.
Warning Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

electric heater TDS 75 / TDS 100 / TDS 120

Warning Children of less than 3 years should be kept away from the device unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
Warning Do not use the device in small rooms if persons are present who cannot leave the room independently and who are not under constant supervision. · Do not use the device in potentially explosive rooms or areas and do not install it there.
· Do not use the device in aggressive atmosphere.
· Only put up the device in an upright, stable position on firm ground.
· Let the device dry out after a wet clean. Do not operate it when wet.
· Do not use the device with wet or damp hands.
· Do not expose the device to directly squirting water.
· Never insert any objects or limbs into the device.
· Do not cover the device during operation.
· Do not remove any safety signs, stickers or labels from the device. Keep all safety signs, stickers and labels in legible condition.
· Do not sit on the device.
· This device is not a toy. Keep away from children and animals. Do not leave the device unattended during operation.
· Check accessories and connection parts for possible damage prior to every use of the device. Do not use any defective devices or device parts.
· Ensure that all electric cables outside of the device are protected from damage (e.g. caused by animals). Never use the device if electric cables or the power connection are damaged!
· The mains connection must correspond to the specifications in the Technical annex.
· Insert the mains plug into a properly fused mains socket.
· Observe the device’s power input, cable length and intended use when selecting extensions to the power cable. Completely unroll extension cables. Avoid electrical overload.

· Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket. Hold onto the mains plug while doing so.
· Switch the device off and disconnect the power cable from the mains socket when the device is not in use.
· Do not under any circumstances use the device if you detect damages on the mains plug or power cable. If the power cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Defective power cables pose a serious health risk!
· When positioning the device, observe the minimum distances from walls and other objects as well as the storage and operating conditions specified in the Technical annex.
· Keep a safety distance of at least 1 m between the air inlet and the air outlet of the device and all combustible materials such as textiles, curtains, beds and sofas.
· Make sure that the air inlet and outlet are not obstructed.
· Do not place the device on combustible ground.
· Only use original spare parts, for otherwise safe and functional operation cannot be ensured.
· Allow the device to cool down before transport and/or maintenance work.
· Do not use the device if it has been dropped or if it shows visible signs of damage.
· Do not use the heating device together with a programming device, a timer, a separate remote control system or any other device that automatically switches the heating device on, as there is a risk of fire if the heating device is covered or incorrectly positioned.
Intended use
Only use the device for heating closed rooms whilst adhering to the technical data. Intended use comprises heating the air in:
Construction trailers greenhouses Boathouses Garages Market stalls Workshops Gastronomy sector Warehouses and halls Shipyards in wet rooms in compliance with the local or national
regulations for the operation of electrical equipment in wet rooms.

electric heater TDS 75 / TDS 100 / TDS 120

Foreseeable misuse · Do not place any objects, e.g. clothing, on the device.
· Do not use this device in the vicinity of fuel, solvents, varnishes or other easily inflammable vapours or in rooms where these substances are stored.
· Do not use the device out of doors.
· Do not use the device for heating in vehicles.
· Do not use the heating device in immediate vicinity of swimming pools, bathtubs and showers.
· Do not place the device on wet or flooded ground.
· Any use other than the intended use is regarded as a reasonably foreseeable misuse.
· Do not make any unauthorised modifications, alterations or structural changes to the device.

Personnel qualifications
People who use this device must: · be aware of the dangers that occur when working with
electric devices in damp areas.
· have read and understood the instructions, especially the Safety chapter.
Maintenance tasks which require the housing to be opened must only be carried out by specialist electrical companies or by Trotec.

Symbols on the device

Symbols

Meaning
This symbol located on the device indicates that it is prohibited to place objects (such as towels, clothes etc.) above or directly in front of the device. In order to avoid overheating and fire hazards, the heater must not be covered.

Residual risks
Warning of electrical voltage Work on the electrical components must only be carried out by an authorised specialist company!
Warning of electrical voltage Before any work on the device, remove the mains plug from the mains socket! Do not touch the mains plug with wet or damp hands. Hold onto the mains plug while pulling the power cable out of the mains socket.
Warning of electrical voltage Risk of electric shock! Risk of an electric shock if the heating device comes into contact with water in bathtubs, showers or swimming pools! Do not use this heating device in immediate proximity to bathtubs, showers or swimming pools!
Warning of hot surface Parts of this appliance can become very hot and cause burns. Particular attention is to be paid when there are children or vulnerable persons present!
Warning Improper handling entails a risk of burning and electric shock. Only use the device as intended!
Warning Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way! Observe the personnel qualifications!
Warning The device is not a toy and does not belong in the hands of children.
Warning Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy.
Warning Improper installation entails a risk of fire. Do not place the device on combustible ground. Do not place the device on high-pile carpets.
Warning In order to avoid overheating and fire hazards, the device must not be covered!

electric heater TDS 75 / TDS 100 / TDS 120

Behaviour in the event of an emergency
1. Switch the device off. 2. In an emergency, disconnect the device from the mains
feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket. 3. Do not reconnect a defective device to the mains.
Overheating protection
The device is provided with a safety thermostat, which is activated by overheating of the device. In such an event the device switches off automatically. When the safety thermostat is activated, allow the device to cool down. Only then start to look for the cause of overheating. Should the problem persist, please contact the customer service.

Information about the device
Device description The electric heater serves to generate and distribute warm air, e.g. in interior spaces. The device generates heat by means of a heating element. The air surrounding the heating element is heated. The heated air is blown into the room by a fan. The device is equipped with an integrated thermostat and so generates a constant flow of warm air. Fan operation without heating function is also possible.
Device depiction TDS 75

TDS 75 RESET

15 kW

5 6

electric heater TDS 75 / TDS 100 / TDS 120

TDS 100
4 3

TDS 100 RESET
22 kW

TDS 120
4

TDS 120

30 kW

6 6

No. Designation 1 Rotary switch temperature 2 Air outlet 3 Selection switch ventilation and heating levels 4 Carrying handles 5 Air inlet 6 Air baffle

electric heater TDS 75 / TDS 100 / TDS 120

Transport and storage
Note If you store or transport the device improperly, the device may be damaged. Note the information regarding transport and storage of the device.
Transport To make the device easier to transport, it is fitted with a carry handle.
Before transporting the device, observe the following: · Switch the device off. · Hold onto the mains plug while pulling the power cable out
of the mains socket. · Do not use the power cable to drag the device. · Allow the device to cool down sufficiently.
Storage Before storing the device, proceed as follows: · Hold onto the mains plug while pulling the power cable out
of the mains socket. · Allow the device to cool down sufficiently. When the device is not being used, observe the following storage conditions: · Store the device in a dry location and protected from frost
and heat. · Store the device in an upright position where it is protected
from dust and direct sunlight. · If required, use a cover to protect the device from invasive
dust. · Place no further devices or objects on top of the device to
prevent it from being damaged.
Assembly and start-up
Scope of delivery · 1 x Electric heater · 1 x manual
Unpacking the device 1. Open the cardboard box and take the device out. 2. Completely remove the packaging. 3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during unwinding.

Start-up
Info Odours might arise upon initial start-up or after a longer period of non-use.
When positioning the device, observe the minimum distance from walls or other objects as described in the chapter Technical annex.

D
· Before restarting the device, check the condition of the power cable. If there are doubts as to the sound condition, contact the customer service.
· Set the device up in an upright and stable position. · Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning the device in the middle of the room. Use cable bridges. · Make sure that extension cables are completely unrolled. · Make sure that no curtains or other objects interfere with the air flow. · Make sure that the device cannot come into contact with moisture or water. Connecting the power cable · Insert the mains plug into a properly fused mains socket. · Make sure that the power cable is guided along the back of the device. Never guide the power cable along the front of the device!

electric heater TDS 75 / TDS 100 / TDS 120

Operation
· Avoid open doors and windows. Control panel TDS 75
7
TDS 75 RESET

15 kW

TDS 100 RESET

3 TDS 120

22 kW
1
TDS 120

No. Designation
1 Rotary switch temperature
3 Selection switch for ventilation and heating levels 0: The device is switched off. : ventilation only : heating level 1 : heating level 2
7 Reset button (TDS 100 only)
Info In the event of a power failure, press the reset button (7) after the mains plug has been removed from the mains socket and after the device has been switched off due to overheating.
Switching the device on
Once you have completely installed the device as described in the chapter Assembly and start-up, you can switch it on. 1. Set the selection switch ventilation and heating levels (3)
to the desired heating level.
Setting the room thermostat 1. Turn the room thermostat’s infinitely variable rotary switch
temperature (1) to the desired temperature range.
The room thermostat controls the room temperature automatically: · When the set value is exceeded, the heating switches off
while the fan keeps running.
Shutdown
Warning of electrical voltage Do not touch the mains plug with wet or damp hands. · Turn the selection switch ventilation and heating levels (3) to ventilation .
· Keep the fan running for 3 minutes before switching the device off.
· Switch off the device by setting the selector switch ventilation and heating levels (3) to the 0 position.
· Hold onto the mains plug while pulling the power cable out of the mains socket.
· Allow the device to cool down completely.
· Clean the device according to the Maintenance chapter.
· Store the device according to the Transport and storage chapter.

30 kW

electric heater TDS 75 / TDS 100 / TDS 120

Errors and faults
Warning of electrical voltage
Tasks which require the device to be opened must only be carried out by authorised specialist companies or by Trotec.
The device has been checked for proper functioning several times during production. If malfunctions occur nonetheless, check the device according to the following list.
The device does not start: · Check the power connection.
· Check the power cable and mains plug for damage. If you notice damages, do not try to take the device back into operation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
· Check the on-site fusing.
· TDS 75 and TDS 100: The internal thermostat does not reset automatically. Actuate the reset button (7) next to the rotary switch temperature (1).
· The motor might be defective. Have a defective motor replaced by a specialist electrical company.
· The room thermostat might be defective. Have a defective room thermostat replaced by a specialist electrical company.
· Wait for 10 minutes before restarting the device. If the device is not starting, have the electrics checked by a specialist company or by Trotec.

The device is switched on, the fan is operating, the heating is not: · Check the room temperature. The room thermostat may
have switched off, because the desired room temperature has been reached.
· Check whether the overheating protection has tripped (see chapter Safety).
· The heating resistor might have blown. Have a defective heating resistor replaced by a specialist electrical company.
· The room thermostat might be defective. Have a defective room thermostat replaced by a specialist electrical company.
The fan is not running: · Check whether the device is switched on.
· Check the power connection.
· Check the power cable and mains plug for damages.
· The fan motor might be defective. Have a defective fan motor replaced by a specialist electrical company.
The air current is reduced: · Check the air inlet and outlet. Make sure that air inlet and
outlet are not obstructed. Remove any dirt. Observe the minimum distance from walls or other objects according to the technical data.
The device is loud or vibrates: · Check whether the device is set up in a stable and upright
position.
Note Wait for at least 3 minutes after maintenance and repair work. Only then switch the device back on.
The device still does not operate correctly after these checks:
Please contact the customer service. If necessary, bring the device to an authorised specialist electrical company or to Trotec for repair.

electric heater TDS 75 / TDS 100 / TDS 120

Maintenance

Maintenance intervals

Maintenance and care interval before every start-up

Check air inlets and outlets for dirt

and foreign objects and clean

if necessary

Check air inlet grid(s) for dirt and

foreign objects and clean

if necessary

Clean the exterior

Visually check the inside of the device for dirt

Check for damage

Check attachment screws

Test run

as needed at least every at least every at least every at least

2 weeks

4 weeks

6 months annually

Maintenance and care log Device type: ………………………………………

Device number: ………………………………

Maintenance and care interval 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Check air inlets and outlets for dirt and foreign objects and clean if necessary
Check air inlet grid(s) for dirt and foreign objects and clean if necessary
Clean the exterior
Visually check the inside of the device for dirt
Check for damage
Check attachment screws
Test run
Comments

1. Date: …………………………….. 2. Date: ……………………………… 3. Date: ……………………………… 4. Date: ……………………………… Signature: ………………………….. Signature: …………………………… Signature: …………………………… Signature: ……………………………
5. Date: …………………………….. 6. Date: ……………………………… 7. Date: ……………………………… 8. Date: ……………………………… Signature: ………………………….. Signature: …………………………… Signature: …………………………… Signature: ……………………………
9. Date: …………………………….. 10. Date: ……………………………. 11. Date: ……………………………. 12. Date: ……………………………. Signature: ………………………….. Signature: …………………………… Signature: …………………………… Signature: ……………………………
13. Date: …………………………… 14. Date: ……………………………. 15. Date: ……………………………. 16. Date: ……………………………. Signature: ………………………….. Signature: …………………………… Signature: …………………………… Signature: ……………………………

electric heater TDS 75 / TDS 100 / TDS 120

Activities required before starting maintenance
Warning of electrical voltage Do not touch the mains plug with wet or damp hands. · Switch the device off. · Hold onto the mains plug while pulling the power cable out of the mains socket. · Allow the device to cool down completely.
Warning of electrical voltage Tasks which require the device to be opened must only be carried out by authorised specialist companies or by Trotec.
Cleaning the housing
Warning of electrical voltage Never immerse the device in water! Clean the housing with a soft, damp and lint-free cloth. Make sure that no moisture enters the housing. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth. Wipe the housing dry after cleaning.

Technical annex

Technical data

Parameter Value

Model

TDS 75

TDS 100

TDS 120

Heating capacity level 1: level 2: level 3: level 4:

Ventilation only Ventilation only Ventilation only

5000 W

11000 W

15000 W

10000 W

22000 W

30000 W

15000 W

–

Air flow rate 1293 m3/h 1632 m3/h 1980 m3/h

Operating range

-20 °C to +45 °C

Mains connection

3/N/PE ~

400 V / 50 Hz 400 V / 50 Hz 400 V / 50 Hz

Max. power 15000 W input

22000 W

30000 W

Nominal

21.7 A

32 A

43 A

current

consumption

Fusing

32 A

35 A

50 A

Plug type

CEE 32 A, 5-pin

CEE 63 A, 5-pin

Type of

IP24

protection

Sound

60 dB(A)

pressure level

(at a distance

of 1 m)

73 dB (A)

Weight

15 kg

20 kg

25 kg

Dimensions

(length x

332 x 405 x

width x height) 540 (mm)

430 x 440 x 610 (mm)

485 x 530 x 785 (mm)

Minimum distance to walls and other objects
top (A): 50 cm rear (B): 50 cm sides (C): 50 cm front (D): 50 cm

50 cm 50 cm 50 cm 50 cm

electric heater TDS 75 / TDS 100 / TDS 120

Circuit diagram TDS 75 Circuit diagram TDS 100 Circuit diagram TDS 120

electric heater TDS 75 / TDS 100 / TDS 120

Overview of spare parts TDS 75

Note! The position numbers of the spare parts differ from those describing the positions of the components mentioned in these instructions.

Spare parts list TDS 75
No. Spare part 1 Front Grill (SPCC) 2 Tubular Electric Heating Element (230V AC 3000W) 3 Knob (PA) 4 Control Panel (SPCC) 5 Heat Insulation Plate (SECC) 6 Left Panel (SPCC) 7 Rotary Switch (250V 16A) 8 Insulation Plate (Epoxy Resin) 9 Thermostat With Probe (400V 32A 40°/140°) 10 Time Delay Thermostat (250V 10A K45) 11 Middle Panel (SECC) 12 Top Cover (SPCC)
13 Protection Bush (PVC)
14 Lock (PA6)

No. Spare part 15 Socket Fixing Plate (SECC) 16 Industrial Plug (400V 32A 5 Core) 17 Air Inlet Grill (SECC) 18 Left Handle (SPCC) 19 Right Handle (SPCC) 20 Plastic Gasket (PA) 21 Motor (400V 50Hz 95W) 22 Air Passage (SECC) 23 Fan (Ø 300) 24 Right Panel (SPCC) 25 Bottom Panel (SPCC) 26 Tubular Electric Heating Element Upper Support
(SECC) 27 Tubular Electric Heating Element Lower Support
(SECC) 28 Sensor Clip (Steel)

electric heater TDS 75 / TDS 100 / TDS 120

Overview of spare parts TDS 100

Note! The position numbers of the spare parts differ from those describing the positions of the components mentioned in these instructions.

Spare parts list TDS 100
NO. SPARE PART 1 Top Panel 2 Inter Panel 3 Left Panel 4 Front Grill 5 Back Grill 6 Control Panel 7 Right Panel 8 Fan Blowing 9 Handle 10 Buttom Panel

NO. SPARE PART 11 Heating Element 12 Thermostat 13 Insulated Panel 15 Switch 16 Relay 17 Plug 18 Fan 19 Motor 20 Screws 23 Knob

electric heater TDS 75 / TDS 100 / TDS 120

Overview of spare parts TDS 120

Note! The position numbers of the spare parts differ from those describing the positions of the components mentioned in these instructions.

Spare parts list TDS 120
No. Spare part 1 Front Grill (SPCC) 2 Knob (PA) 3 Control Panel (SPCC) 4 Mica Sheet (0,9mm) 5 Rotary Switch (IK233-4/250V15A) 6 Temperature Controller (YT-WN16 250V/16A/85°C) 7 Insulation Palte (Epoxy Resin) 8 Time Delay Thermostat (KSD301/250V/10A/K45) 9 Re-set Thermostat (KSD301-V/250V/16A) 10 Contactor (HLC-3XWO4BBC 400V 50A 50Hz) 11 Relay (JQX-76F-TU-2A 380-400V AC 25A) 12 Middle Panel (SECC) 13 Air Passage (SECC) 14 Industrial Plug (400V 63V) 15 Heat Insulation Plate (SECC)
16 Top Cover (SPCC)
17 Capacitor (CBB60/ 450V 5µ F) 18 Capacitor Stents (SECC)

No. Specifications 19 Left Panel (SPCC) 20 Plastic Gasket (PA) 21 Fan (Ø 350mm) 22 Motor ( YSK-70-4 400V 50Hz) 23 Air Inlet Grill (SPCC) 24 Air Inlet Grill Fixing Plate (SECC) 25 Before The Steel Tube (Ø 19*1.0mm) 26 After The Stell Tube (Ø 19*1.0mm) 27 Tupe Cap (Ø 19 mm/PA) 28 Right Panel (SPCC) 29 Pull Rivet Nuts (M10) 30 Stopple (Ø10) 31 Bottom Panel (SPCC) 32 Rase Heat Insulation Plate (SECC) 33 Tubular Electric Heating Element Upper Support
(SECC) 34 Tubular Electric Heating Element Lower Support
(SECC) 35 Tubular Electric Heating Element Support (SECC) 36 Tubular Electric Heating Element (230V 5000W)

electric heater TDS 75 / TDS 100 / TDS 120

Disposal
Always dispose of packing materials in an environmentally friendly manner and in accordance with the applicable local disposal regulations.
The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment must not be disposed of with the household waste at the end of its life. You will find collection points for free return of waste electrical and electronic equipment in your vicinity. The addresses can be obtained from your municipality or local administration. You can also find out about other return options that apply for many EU countries on the website https://hub.trotec.com/?id=45090. Otherwise, please contact an official recycling centre for electronic and electrical equipment authorised for your country.
The separate collection of waste electrical and electronic equipment aims to enable the re-use, recycling and other forms of recovery of waste equipment as well as to prevent negative effects for the environment and human health caused by the disposal of hazardous substances potentially contained in the equipment.
Only for United Kingdom
According to Waste Electrical and Electronic Equipment Regulations 2013 (2013/3113) devices that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

Declaration of conformity

Declaration of conformity in accordance with the EC Machinery Directive 2006/42/EC, Annex II, Part 1, Section A

We Trotec GmbH declare in sole responsibility that the product designated below was developed, constructed and produced in compliance with the requirements of the EC Machinery Directive in the version 2006/42/EC.

Product model / product:

TDS 75 TDS 100 TDS 120

Product type:

electric heater

Year of manufacture as of: 2021

Relevant EU directives: · 2011/65/EU: 01/07/2011
· 2012/19/EU: 24/07/2012
· 2014/30/EU: 29/03/2014

· 2015/863/EU: 31/03/2015

Applied harmonised standards: · EN 55014-1:2017

· EN 60335-1:2012/A13:2017 · EN 60335-2-30:2009 · EN 60335-2-30:2009/A11:2012 · EN 61000-3-11:2000

· EN 61000-3-12:2011

Applied national standards and technical specifications: · EN 55014-2:2015
· EN 62233:2008

Manufacturer and name of the authorised representative of the technical documentation:
Trotec GmbH