P0378 Mini Pendant Matte
Product Information: ASSEMBLY AND INSTALLATION INSTRUCTIONS
(P0378)
This product is a light fixture that requires assembly and
installation. The package includes a mounting strap unit, mounting
screw, wire connector, bolt nut, flat head screwdriver, strain
relief, canopy kit, and glass shade. The product requires a Max.
60W Type A Bulb which is not included in the package. It is
important to read and save the instruction manual before
installation. Before installing, it is advised to consult local
electrical codes for wiring and grounding requirements.
It is important to shut off power while installing or servicing
this fixture to avoid the risk of electrical shock. The product
comes with a spare parts list that includes a mounting strap unit,
mounting screw, wire connector, mounting hardware 6587MM, bolt nut,
flat head screwdriver, and glass shade which are available for
re-order if damaged or missing.
Product Usage Instructions
- Turn off the power at fuse or circuit box before starting the
installation process. - Fasten the cable by screwing the plastic headless screw using a
flat head screwdriver. - Measure the desired length of the cable from the canopy to the
top side of the cap nut and leave an additional 9 inches of cable
above the canopy (include the canopy), then cut off the unnecessary
cable. Adjust strain relief at 9 position from the top of the
cord. - Mark 3 inches of cord from the top of the cord and use a knife
to peel off the insulation of the cord carefully to expose the
three wires on the inside. Peel off the wire from the top about 3/8
inch long to expose the copper wires. - Attach the mounting strap unit to the outlet box using two
mounting screws. - Pull out the outlet wires and the house ground wire from the
outlet box. Connect the wires using the wire connector:
- The black wire from the fixture to the black wire from the
power source. - The white wire from the fixture to the white wire from the
power source. - The green ground wire from the fixture to the green ground wire
from the power source.
hex nut. Note: Adjusting the strain relief of the canopy can
decrease or increase the length of cord that is exposed.
inserting the screws and secure it with two bolt nuts.
relamping label at socket area or packaging for maximum wattage
allowed.
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
P0378
WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THIS INSTRUCTION.
Hardware Package (included):
Mounting Strap Unit (A)
Mounting Screw (B)
Wire Connector (C)
Bolt Nut (D)
Flat HeadScrew driver (E)
Outlet Box House Ground Wire
Wire Connector (C)
Mounting Strap Unit (A)
Fixture Mounting Screw
Green Ground Screw Lock Nut Mounting Screw (B) Strain Relief
Canopy Kit Bolt Nut (D)
Installation Steps
Turn off the power at fuse or circuit box.
Cable
1. Fastening cable by screwing plastic headless screw, using flat headscrew driver (E).
2. Measure the desired length of the cable (a) from the canopy to the top side of the cap nut and leave an additional 9″ of cable (b) above the canopy (include the canopy), then cut off the unnecessary cable. (See Figure 1)
Flat HeadScrew driver (E)
c (3″)
d (3/8″)
b (9″)
3. Adjust strain relief at 9″ position from the top of the cord.
4. Mark the 3″ of cord (c) from the top of the cord (b). Use a knife to peel off the insulation of the cord (c) carefully to expose the 3 wires on the inside. (See Figure 1) Caution: Cutting too deep may cut off the three inside wires and destroy the insulation surface of the three inside wires.
5. Peel off the wire from the top about 3/8″ long (d) to expose the copper wires.
a Figure.1
6. Attach the mounting strap unit (A) to the outlet box by using two mounting screws (B).
7. Pull out the outlet wires and the house ground wire from the outlet box. Make wire connections using the wire connector (C) : a. The black wire from the fixture to the black wire from the power source. b. The white wire from the fixture to the white wire from the power source. c. The green ground wire from the fixture to the green ground wire from power source. Carefully put wires back into the outlet box.
8. Pull the cord (a) down slightly until the strain relief touches the hex nut. Note: Adjusting the strain relief of the canopy can decrease orincrease the length of cord that is exposed.
Glass Shade
Max. 60W Type A Bulb (Not Included)
221020
9. Attach the fixture canopy to the mounting strap unit (A) by inserting the screws, and secure it with two bolt nuts (D). 10. Install 1 x 60W Max. medium base bulb (not included).
See relamping label at socket area or packaging for maximum wattage allowed.
Turn on the power at fuse or circuit box.
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Mounting Strap Unit (A)
Mounting Screw (B)
Wire Connector (C)
Mounting Hardware 6587MM (1 SET)
Bolt Nut (D)
Flat HeadScrew driver (E)
Glass Shade 10331SG
A
A: 8-1/4″
B: 6″
B
221018
