21144 4-Light Vanity Wall Light

Product Information: 4 Light Vanity

The 4 Light Vanity is a lighting fixture that comes with a
pre-assembled mounting bracket and fixture body. It includes
hardware parts such as support screws, hex nuts, cap nuts, outlet
box screws, wire connectors, green ground screw, and socket rings.
The fixture can be assembled with glass shades facing up or down
and can hold up to four medium base (E26) type A bulbs with a
maximum wattage of 60W or medium base (E26) self-ballasted LED
bulbs with a maximum wattage of 9W.

Usage Instructions

1. Preparation: Read the important safety
   information in the manual before starting the installation
   process.
2. Installation:
   1. Prepare the mounting bracket by attaching the pre-assembled H1
      mounting bracket to the fixture body using the H4 outlet box screw
      (short) and H2 support screw (long) with H3 hex nuts.
   2. Install the mounting bracket by using the pre-assembled H7 cap
      nut, which connects to the mounting bracket, and securing it with
      the provided hardware.
   3. Make the electrical connections by connecting the wires from
      the outlet box to the wire connectors on the mounting bracket using
      H5 green ground screw and H6 wire connectors.
   4. Assemble the fixture body to the outlet box by attaching the
      mounting bracket to the outlet box using H1 mounting bracket and
      securing it with the provided hardware.
3. Assembly: The shades can be assembled facing
   up or down depending on your preference.
4. Light Bulbs: Install the light bulbs by
   inserting up to four medium base (E26) type A bulbs with a maximum
   wattage of 60W or medium base (E26) self-ballasted LED bulbs with a
   maximum wattage of 9W.
5. Cleaning: Clean the fixture with a soft, dry
   cloth. Do not use any cleaning solutions or abrasive
   materials.
6. Troubleshooting: If you experience any issues
   with the fixture, refer to the troubleshooting section in the
   manual or contact customer support for assistance.

USE AND CARE MANUAL
4 LIGHT VANITY
A B

H1 Mounting bracket
(Pre-assembled to fixture body)
1 pc H4 Outlet box screw (short) 2 pcs
H7 Cap nut
(Pre-assembled to mounting bracket)
2 pcs

Hardware (Parts are not to scale)

H2 Support screw (long)

H3 Hex nut

2 pcs

2 pcs

H5 Green ground screw
(Pre-assembled to mounting bracket)
1 pc
H8 Socket ring
(Pre-assembled to fixture body)
4 pcs

H6 Wire connector 3 pcs

THIS MANUAL CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Page 1 of 4

IMPORTANT SAFETY INFORMATION
· Please read and understand this entire manual before attempting to assemble, operate or install the product.
· Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or switching off circuit breaker).
· Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electric shock.
· All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC). Contact your municipal building department to learn about your local codes, permits and/or inspections. If you do not have electrical wiring experience, refer to a do-it-yourself wiring handbook or have your fixture installed by a qualified licensed electrician.
· Risk of fire ­ most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified electrician before installation.
· Do not exceed the recommended wattage. Refer to the re-lamping label on the light socket for maximum wattage.
· Do not replace a bulb when electrical outlet switch is turned to the “ON” position. · Do not immerse your lamp in water; doing so will damage the wire. · Keep materials that burn easily away from lighted bulbs.

PREPARATION
· Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts.
· Tools required for assembly (not included): flathead screwdriver, phillips screwdriver, pliers, electrical tape, wire cutters, safety glasses, ladder, wire stripper.

INSTALLATION

1 Preparing the mounting bracket
· Tighten the support screws (long) (H2) into the inside mounting bracket hole of the mounting bracket (H1) (to be full tightened later), and secure with hex nuts (H3).

2 Installing the mounting bracket
· Fasten the mounting bracket (H1) onto the outlet box using two outlet box screws (short) (H4).

H1

H4

H2

H1

H3
Page 2 of 4

INSTALLATION (continued)

3 Making the electrical connections

· Strip 3/4 in. of insulation from the wire ends.
· Connect the black wire from the fixture to the black wire from the outlet box, then connect the white wire from the fixture to the white wire from the outlet box.
· The bare copper ground wire from the fixture must loop one turn under the head of the green ground screw (H5) on the mounting bracket (H1) before it is connected to the ground conductor of the supply circuit.
· Cover the wires with wire connectors (H6). Tape the wire connectors (H6) and wires together, and carefully position all wires inside the outlet box.

H1 H5

H6 A

4 Assembling the fixture body to the outlet box
· Place the fixture body (A) over the outlet box, and ensure the heads of the support screws (long) (H2) come through the holes of back of the fixture body (A).
· Tighten the cap nuts (H7) onto the protruding support screws (long) (H2) on the mounting bracket (H1) until the fixture body (A) is held firmly against the wall.
Note: The shades on this fixture can be installed facing up or facing down.
H1 A

OPTION 1: Mount with glass

H2

shades facing down.

H7
Page 3 of 4

OPTION 2: Mount with glass shades facing up.

INSTALLATION (continued)

5 Assembling the glass shades
· Unscrew the socket rings (H8) from the sockets on the fixture body (A).
· Place the glass shade (B) over the socket, then tighten the socket ring (H8).

6 Installing the light bulbs
· Install the light bulbs (not provided) into each socket. Use four MAX 60 W medium base (E26) type “ST64” bulbs (recommended).
Note: You can also use four MAX 60 W medium base (E26) type “A” bulbs or MAX 9W medium base (E26) self-ballasted LED bulbs. Do not exceed the recommended wattage.

A

A

B

B

H8

CLEANING
· Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry, soft cloth to dust or wipe carefully.
· To clean the fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. Use a dry or slightly dampened, clean cloth to wipe the exterior surface of the fixture.
TROUBLESHOOTING
· The light does not come on at all: a) Make sure the wall switch and circuit breaker are on. b) Make sure the wiring is correct.
· Fuse blows or circuit trips when light is turned on. a) Check for crossed wires, ensure wiring is correct.

Page 4 of 4