T0633 Outdoor Wall Lantern with Clear Glass
Product Information
The T0633/T0634 is a fixture that comes with a photocell
function to enable automatic turning on at dusk and off at dawn.
The package includes a mounting plate unit, mounting screw, wire
connector, photocell, bolt nut, rubber pad, fixture, rubber pad,
outlet box house grounding wire, headless screw, green grounding
screw, mounting plate unit, fixture grounding wire, fixture wire
backplate, set screw, frame, glass shade clip, and can accommodate
a maximum of 60W Type A bulb (not included).
Product Usage Instructions
- Before installation, consult local electrical codes for wiring
and grounding requirements. - Turn off the main power at the circuit breaker before
installing the fixture. - Unscrew the two bolt nuts (D), remove the two rubber pads (E),
and the mounting plate unit (A) from the backplate. - Attach the mounting plate unit (A) to the outlet box by using
two mounting screws (B). Adjust the length of the preinstalled
headless screws if necessary. Ensure that two headless screws are
lined up horizontally to make the fixture level. - Gently place the glass shade into the metal frame, then secure
it by pressing the clips from the top side. - Attach the metal frame to the fixture by aligning the hole and
then secure it with the two set screws. - Install the bulb (not included). See relamping label at socket
area or packaging for maximum wattage allowed. - Attach the backplate of the fixture to the mounting plate unit
(A) by aligning and inserting the two headless screws into set
holes on backplate, then secure it with two rubber pads (E) and two
bolt nuts (D). With silicone caulking compound, caulk completely
around where the backplate meets with the wall surface to prevent
water from seeping into the outlet box. - Turn on the power at fuse or circuit box.
- To disconnect the Dusk-to-Dawn Photocell: Turn off the power at
the fuse or circuit box before starting installation. Loosen the
wire connector connected with the wires from photocell (See Fig.1).
Note: Do not remove the photocell to prevent water from seeping
into the outlet box. - Take a white pigtail and black pigtail and make wire
connections using wire connector (C): (See Fig.2)- The black wire from the fixture to one end of the black
pigtail. - The white wire from the fixture to one end of the white
pigtail. - The other end of the black pigtail to the black wire from the
power source. - The other end of the white pigtail to the white wire from the
power source. Put all wires back into the backplate of the
fixture.
- The black wire from the fixture to one end of the black
ASSEMBLY AND INSTALLATION INSTRUCTIONS
T0633 / T0634
WWARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Plate Unit (A)
Mounting Screw (B)
Wire Connector (C)
Photocell
Bolt Nut (D)
Rubber Pad (E)
Fixture
Rubber Pad (E) Bolt Nut (D)
Outlet Box House Grounding Wire
Headless Screw Green Grounding Screw Mounting Plate Unit (A)
Mounting Screw (B) Fixture Grounding Wire
Wire Connector (C) Fixture Wire Backplate
IMPORTANT: The sensor has an excellent photocell function to enable the light to turn on at dusk and off at dawn automatically.
Set Screw
Frame
Glass Shade Clip
Max.60W Type A Bulb (not included)
T
220314
Installation Steps
Turn off the power at fuse or circuit box.
1. Unscrew the two bolt nuts (D)
remove the two rubber pads (E) and the mounting plate unit (A) from the backplate.
2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled headless screws if necessary. Note: Make sure that two headless screws are lined up horizontally to make the fixture level.
3. Gently place the glass shade into the metal frame, then secure it by pressing the clips from top side.
4. Attach the metal frame to the fixture by aligning hole, then secure it with the two set screws.
5. Install the bulb (not included). See relamping label at socket area or packaging for maximum wattage allowed.
6. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows: · Connect the hot wire (usually black insulation) from the fixture to the black wire from the power source. · Connect the neutral wire (usually white insulation) from the fixture to the white wire from the power source. · Attach the fixture grounding wire (usually green with the insulation or bare wire) to the mounting plate unit (A) with green grounding screw. Then, depending on local code, connect it to the house grounding wire with the wire connector (C). Carefully put all of the wires back into the outlet box.
7. Attach the backplate of the fixture to the mounting plate unit (A) by aligning and inserting the two headless screws into set holes on backplate, then secure it with two rubber pads (E) and two bolt nuts (D). Note: With silicone caulking compound, caulk completely around where the backplate meets with the wall surface to prevent water from seeping into the outlet box.
Turn on the power at fuse or circuit box.
Optional Installation: Disconnect Dusk-to-Dawn Photocell
IMPORTANT: Compatible with dimmer when photocell is disconnected. * Requires dimmable bulb and compatible dimmer switch.
Photocell Black Wires From Photocell White Wires From Photocell Red Wires From Photocell
Wire Connector
Wires From Fixture
Wires From Main Power
Pigtail
Wires From Fixture
White Pigtail
Fig.1
Wire Connector (C)
Fig.2
220314
1. Turn off the power at the fuse or circuit box before starting installation.
2. Loosen the wire connector connected with the wires from photocell. (See Fig.1) Note: Do not remove the photocell to prevent water from seeping into the outlet box.
3. Take a white pigtail and black pigtail and make wire connections using wire connector (C): (See Fig.2) a. The black wire from the fixture to one end of the black pigtail. b. The white wire from the fixture to one end of the white pigtail. c. The other end of the black pigtail to the black wire from the power source. d. The other end of the white pigtail to the white wire from the power source. Put all wires back into the backplate of the fixture.
Turn on the power at fuse or circuit box.
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Mounting Plate Unit (A) Mounting Screw (B) Wire Connector (C) Bolt Nut (D) Rubber Pad (E)
Assembly Kit 6492MM (1 SET) for T0633 6493MM (1 SET) for T0634
Glass Shade 10284CS for T0633 10285CS for T0634
A B
T0633 A: 12″ B: 5-1/2″ C: 6-3/4″
T0634
A: 13-3/4″
B: 6-1/2″
C
C: 8-1/4″
220314
