Vaxcel T0683 Winfield 1 Light Dusk To Dawn Matte Black Outdoor Wall Lantern Clear Cylinder Glass Instruction Manual

T0683 Winfield 1 Light Dusk to Dawn Matte Black Outdoor Wall Lantern Clear Cylinder Glass

Product Information:

The T0683 is a light fixture that comes with a sensor that has
an excellent photocell function to turn on the light at dusk and
off at dawn automatically. The fixture is compatible with a dimmer
when the photocell is disconnected. It requires a maximum of 60W
Type ST bulb, which is not included in the hardware package. The
package includes a mounting plate unit, mounting screw, wire
connector, bolt nut, rubber pad, and glass shade.

Product Usage Instructions:

1. Before installing the fixture, consult local electrical codes
   for wiring and grounding requirements.
2. Turn off the main power at the circuit breaker before
   installing the fixture.
3. Unscrew the two bolt nuts (D) and remove the two rubber pads
   (E) and the mounting plate unit (A) from the backplate.
4. Attach the mounting plate unit (A) to the outlet box using two
   mounting screws (B). Adjust the length of the preinstalled fixture
   mounting screws if necessary. Make sure that two fixture mounting
   screws are lined up horizontally to make the fixture level.
5. Install the bulb (not included). See relamping label at socket
   area or packaging for maximum wattage allowed.
6. Attach the backplate of the fixture to the mounting plate unit
   (A) by aligning and inserting the two fixture mounting screws into
   set holes on the backplate, then secure it with two rubber pads (E)
   and two bolt nuts (D). With silicone caulk compound, caulk
   completely around where the backplate meets with the wall surface
   to prevent water from seeping into the outlet box.
7. If necessary, disconnect the dusk-to-dawn photocell. Turn off
   the power at the fuse or circuit box before starting
   installation.
8. Loosen the wire connector connected with the wires from the
   photocell. Do not remove the photocell to prevent water from
   seeping into the outlet box.
9. Take a white pigtail and black pigtail and make wire
   connections using wire connector (C). The black wire from the
   fixture to one end of the black pigtail. The white wire from the
   fixture to one end of the white pigtail. The other end of the black
   pigtail to the black wire from the power source. The other end of
   the white pigtail to the white wire from the power source. Put all
   wires back into the backplate of the fixture.
10. Turn on the power at the fuse or circuit box.

Spare Parts List:

• Mounting Plate Unit (A)
• Mounting Screw (B)
• Wire Connector (C)
• Bolt Nut (D)
• Rubber Pad (E)
• Glass Shade

ASSEMBLY AND INSTALLATION INSTRUCTIONS
T0683
WWARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):

Mounting Plate Unit (A)

Mounting Screw (B)

Wire Connector (C)

Bolt Nut (D)

Rubber Pad (E)

Photocell

Outlet Box House Ground Wire Fixture Mounting Screw Green Ground Screw Mounting Plate Unit (A) Mounting Screw (B) Fixture Ground Wire Wire Connector (C)
Fixture Wire Backplate
IMPORTANT: The sensor has an excellent photocell function to enable the light to turn on at dusk and off at dawn automatically.

Fixture Bolt Nut (D) Rubber Pad (E)
Glass Shade
Max.60W Type ST Bulb (not included)

Page 1 / 3

221017

T

Installation Steps
Turn off the power at fuse or circuit box.
1. Unscrew the two bolt nuts (D)
remove the two rubber pads (E) and the mounting plate unit (A) from the backplate.
2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled fixture mounting screws if necessary. Note: Make sure that two fixture mounting screws are lined up horizontally to make the fixture level.
3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows: · Connect the hot wire (black insulation) from the fixture to the black wire from the power source. · Connect the neutral wire (white insulation) from the fixture to the white wire from the power source. · Attach the fixture ground wire (bare wire) to the mounting plate unit (A) with green ground screw, then depending on local code, connect it to the house ground wire with the wire connector (C). Carefully put all of the wires back into the outlet box.
4. Install the bulb (not included). See relamping label at socket area or packaging for maximum wattage allowed.
5. Attach the backplate of the fixture to the mounting plate unit (A) by aligning and inserting the two fixture mounting screws into set holes on backplate, then secure it with two rubber pads (E) and two bolt nuts (D). Note: With silicone caulk compound, caulk completely around where the backplate meets with the wall surface to prevent water from seeping into the outlet box.
Turn on the power at fuse or circuit box.

Optional Installation: Disconnect Dusk-to-Dawn Photocell
IMPORTANT: Compatible with dimmer when photocell is disconnected. * Requires dimmable bulb and compatible dimmer switch.

Photocell Black Wires From Photocell White Wires From Photocell Red Wires From Photocell
Wire Connector

Wires From Fixture
Wires From Main Power

Pigtail

Wires From Fixture

White Pigtail
Fig.1

Wire Connector (C)
Fig.2

1. Turn off the power at the fuse or circuit box before starting installation.
2. Loosen the wire connector connected with the wires from photocell. (See Fig.1) Note: Do not remove the photocell to prevent water from seeping into the outlet box.
3. Take a white pigtail and black pigtail and make wire connections using wire connector (C): (See Fig.2) a. The black wire from the fixture to one end of the black pigtail. b. The white wire from the fixture to one end of the white pigtail. c. The other end of the black pigtail to the black wire from the power source. d. The other end of the white pigtail to the white wire from the power source. Put all wires back into the backplate of the fixture.
Turn on the power at fuse or circuit box.

Page 2 / 3

221017

The following parts are available for re-order if damaged or missing.
Spare Parts List:

Assembly Kit 6592MM

Mounting Plate Unit (A) Mounting Screw (B) Wire Connector (C) Bolt Nut (D) Rubber Pad (E)

Glass Shade 10335CG

A B

A: 11-1/2″ B: 5-3/4″ C: 5-1/2″
C

Page 3 / 3

221017